Hi,
You most probably kept the invoice
So contact digium. My experience was that they are human
Regards,
t. jacobson
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Trevor Peirce
Sent: dimanche 22 avril 2007 19:58
To: Asterisk Users Mailing List -
hi,
i think, by default, 'uniqueID' is created by the asterisk.
if this is correct, you would (eventually) have non-uniqueID's
i saw somewhere in the wiki that someone suggested a change (in the code ?) so
that 'uniqueID' would be generated by the database. unique-id being the
primary key and
hi,
i think the problem is here :
exten = _321[0123],n,Dial(SIP/${EXTEN}),30,to)
|
replace with
exten = _321[0123],n,Dial(SIP/${EXTEN},30,to)
note, i removed the parenthesis ')' after the {EXTEN}
this should do
regards,
jacobson
---
Scarlet ONE -
hi,
hi, i did wrote (assembler) programs for cp/m!
if your experience is more on telephony', i think you will find trixbox
easier. in one cd you will have a ready system.
if your hardware is fully recognized, great !
do not use a too old machine nor a too new one.
mind that the install will
cat5 cables are ok if you use straight cables.
crossed cables are different as ethernet signals use other pin layout than e1.
and beside the 'official' e1 crossed, there seems to be other layouts.
this has been discussed here, so browse the archives.
(my pc gives me headaches now, otherwise i
Hi,
With 30 users and NO transcoding, that is
certainly enough.
Even if you use real-time
configuration (that requires a SQL server)
Now, if you system will be accessible both
from inside (LAN) and outside (Internet), I would advice a second network card (10/100)
Regards,
T.
Hi,
I am using ooh323.
I cannot setup a call towards a cisco gateway.
The cisco rejects the call right away with :
Cause value: Mandatory information
element is missing (96)
This
is in the q931 part.
Cisco explanation
Indicates
that the equipment that is sending this code
and the fixed it right
away.
Dan
From:
[EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
On Behalf Of jacobso1
Sent: Thursday, December 08, 2005
8:21 AM
To:
asterisk-users@lists.digium.com
Subject: [Asterisk-Users] OOH323
towards cisco gateway (2691) call setupfails at q931: Mandatory
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of jacobso1
Sent: Thursday, December 08, 2005 1:37 PM
To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
Subject: RE: [Asterisk-Users] OOH323 towards cisco gateway
(2691
Dan,
I'd recommend reporting the problem along with a debug log and
traces from the router to: ooh323c-devel@lists.sourceforge.net
The developers have been quite responsive to problems I've had.
Thank you for tips.
I thing I must recompile the ooh323 module with 'make debug' then 'make
If you do not have a budget, grandstream is not bad
You do not get what you do not pay
But you do not allways get what you paid for
t. Jacobson
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Christian
Victor
Sent: vendredi 23 juin 2006 14:25
To:
Unless my brain did melt down under the
high heat here, there are a few things I would share :
-
1 channel u-law uses at least 80k because of encapsulation
So,
think about compression
-
You can never use 100% of a bandwidth. (80% is a good max)
-
The values given are maximum values,
Hi,
Try to swap both fxo modules.
This way you will notice if the module is out or another problem is present.
The tdm400 could be damaged or there is a configuration problem.
Regards,
-Original Message-
From: [EMAIL PROTECTED] [mailto:asterisk-users-
Hello list,
Howto be shure if one
13 matches
Mail list logo
