Re: [asterisk-users] New Installed X100p
Steve Totaro wrote: I have had Digium tech support tell me to do the same thing I'm hoping that wasn't the final conclusion in the tech support debugging process. If it was, than I am very sorry to hear that, and will make note of it. -- Matthew Fredrickson Software/Firmware Engineer Digium, Inc. Thanks, Steve G B wrote: Hi, I appreciate the help. I called the vendor of the card and they recommended removing all of the PCI cards on the system (including the video card), and moving the card to a new PCI slot. I did all of them together, ran the system headless, and ssh'ed in remotely. It worked! haha... This must be proof that I have purchased a real piece of @#$. Thanks for all of your help. Date: Sat, 8 Sep 2007 02:41:50 +0300 From: [EMAIL PROTECTED] To: asterisk-users@lists.digium.com Subject: Re: [asterisk-users] New Installed X100p On Fri, Sep 07, 2007 at 08:45:11AM -0700, G B wrote: Hi Tzafrir, I am not sure what to look for, so I haveattached both the contents of /var/log/kern.log as well as the outputof dmesg. If you are looking for something specific, I simply asked for a few lines around that message. Anyway, the relevant lines are: Relevant lines: [ 39.337207] Failed to initailize DAA, giving up... [ 39.337283] wcfxo: probe of :00:0c.0 failed with error -5 No more details. This may be a defective card. I have also seen some cases where some voodoo at the PCI layer was required (e.g: passing the boot option pci=noacpi). -- Tzafrir Cohen icq#16849755 jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users Can you find the hidden words? Take a break and play Seekadoo! Play now! http://club.live.com/seekadoo.aspx?icid=seek_wlmailtextlink ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
Matthew Fredrickson wrote: Steve Totaro wrote: I have had Digium tech support tell me to do the same thing I'm hoping that wasn't the final conclusion in the tech support debugging process. If it was, than I am very sorry to hear that, and will make note of it. Thanks, yes, that was the final resolution. I have also heard That motherboard or that server is not supported. Again, this was quite some time ago and Digium has changed as a company as well as the product line, the whole entity has matured. Might be a non-issue now. Let me ask you this, is using a T1 card for ISDN data supported now? That one irked me since it was a selling point, but when calling for support I was told, It can do it but it is not supported. and info on the net was VERY sparse for accomplishing this (circa 2003) Thanks, Steve Totaro ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
Steve Totaro wrote: Matthew Fredrickson wrote: Steve Totaro wrote: I have had Digium tech support tell me to do the same thing I'm hoping that wasn't the final conclusion in the tech support debugging process. If it was, than I am very sorry to hear that, and will make note of it. Thanks, yes, that was the final resolution. I have also heard That motherboard or that server is not supported. Again, this was quite some time ago and Digium has changed as a company as well as the product line, the whole entity has matured. Might be a non-issue now. I would hope so too as well. We're working to change a lot of things that have caused us problems in the past. Part of that problem was learning to deal with a tremendous amount of growth in a short period of time, which I would imagine is difficult for any small company. Let me ask you this, is using a T1 card for ISDN data supported now? I believe it should be working well now, a while ago I spent a bit of time making sure the zaptel portion of it functionally didn't have any problems across a range of kernels. I know that one of the reasons why that support did not support that was (IIRC) it sometimes involved recompiling a systems kernel, or upgrading a systems kernel, which is not an insignificant thing to do for a customer. Though I have not had to look at it in a while, I believe that at the very least it could be easier now, with the packaging of some of the hdlc utils in zaptel so that it works correctly across kernel versions. That one irked me since it was a selling point, but when calling for support I was told, It can do it but it is not supported. and info on the net was VERY sparse for accomplishing this (circa 2003) Sorry again about you trouble with that. I hope that somehow we can win you back :-) Thanks, Steve Totaro ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- Matthew Fredrickson Software/Firmware Engineer Digium, Inc. ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
G B wrote: Hi, I appreciate the help. I called the vendor of the card and they recommended removing all of the PCI cards on the system (including the video card), and moving the card to a new PCI slot. I did all of them together, ran the system headless, and ssh'ed in remotely. It worked! haha... This must be proof that I have purchased a real piece of @#$. Glad you said it without us having to. At least it was cheap, right? -Stephen- ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
Steve Totaro wrote: I am the last one to pickup a manual or call tech support but yesterday I was working on a very large industrial ShopBot (It is a robot so that is cool and it does really awesome things but why I was working on it don't ask.. http://www.shopbottools.com/applications.htm ) After trying a million things, briefly looking at the manual, I called the tech support line. The guy had me check two things, change one thing and everything was joyful. Had I done that from the start, I would have saved three or four hours (I bill by the hour so it's not so bad, but I couldn't bill the full rate since conscience told me not to) Show us your Asterisk configs for the ShopBot. Can I build a dresser from payphone? -Stephen- ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
Hi, I appreciate the help. I called the vendor of the card and they recommended removing all of the PCI cards on the system (including the video card), and moving the card to a new PCI slot. I did all of them together, ran the system headless, and ssh'ed in remotely. It worked! haha... This must be proof that I have purchased a real piece of @#$. Thanks for all of your help. Date: Sat, 8 Sep 2007 02:41:50 +0300 From: [EMAIL PROTECTED] To: asterisk-users@lists.digium.com Subject: Re: [asterisk-users] New Installed X100p On Fri, Sep 07, 2007 at 08:45:11AM -0700, G B wrote: Hi Tzafrir, I am not sure what to look for, so I haveattached both the contents of /var/log/kern.log as well as the outputof dmesg. If you are looking for something specific, I simply asked for a few lines around that message. Anyway, the relevant lines are: Relevant lines: [ 39.337207] Failed to initailize DAA, giving up... [ 39.337283] wcfxo: probe of :00:0c.0 failed with error -5 No more details. This may be a defective card. I have also seen some cases where some voodoo at the PCI layer was required (e.g: passing the boot option pci=noacpi). -- Tzafrir Cohen icq#16849755jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _ Can you find the hidden words? Take a break and play Seekadoo! http://club.live.com/seekadoo.aspx?icid=seek_wlmailtextlink___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
On Sat, Sep 08, 2007 at 12:42:34AM -0700, G B wrote: Hi, I appreciate the help. I called the vendor of the card and they recommended removing all of the PCI cards on the system (including the video card), and moving the card to a new PCI slot. I did all of them together, ran the system headless, and ssh'ed in remotely. It worked! haha... This must be proof that I have purchased a real piece of @#$. One note: The above description still does not completely exclude the possibility that the card wasn't originally placed well. (But then again, what do I really know about PCI cards) -- Tzafrir Cohen icq#16849755jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
G B wrote: Date: Fri, 7 Sep 2007 07:13:38 -0400 From: [EMAIL PROTECTED] To: asterisk-users@lists.digium.com Subject: Re: [asterisk-users] New Installed X100p G B wrote: Hi, I just installed an X100p knockoff (OpenVox a100lp). I have seen my errors in the mailing list but without resolution. It seems that the other problems had to do with IRQ sharing. However, it doesn't seem like the X100p is sharing an IRQ channel with anything. Any ideas? snip Does OpenVox not provide support for their hardware? Thanks, Steve I purchased the card from a third party reseller. I am also contacting them for support. I'll send out an email if they have the solution. Yeah give them a try. I wouldn't even mention that you bought it from a 3rd party. Just play dumb. I am the last one to pickup a manual or call tech support but yesterday I was working on a very large industrial ShopBot (It is a robot so that is cool and it does really awesome things but why I was working on it don't ask.. http://www.shopbottools.com/applications.htm ) After trying a million things, briefly looking at the manual, I called the tech support line. The guy had me check two things, change one thing and everything was joyful. Had I done that from the start, I would have saved three or four hours (I bill by the hour so it's not so bad, but I couldn't bill the full rate since conscience told me not to) Thanks, Steve Totaro ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
I have had Digium tech support tell me to do the same thing Thanks, Steve G B wrote: Hi, I appreciate the help. I called the vendor of the card and they recommended removing all of the PCI cards on the system (including the video card), and moving the card to a new PCI slot. I did all of them together, ran the system headless, and ssh'ed in remotely. It worked! haha... This must be proof that I have purchased a real piece of @#$. Thanks for all of your help. Date: Sat, 8 Sep 2007 02:41:50 +0300 From: [EMAIL PROTECTED] To: asterisk-users@lists.digium.com Subject: Re: [asterisk-users] New Installed X100p On Fri, Sep 07, 2007 at 08:45:11AM -0700, G B wrote: Hi Tzafrir, I am not sure what to look for, so I haveattached both the contents of /var/log/kern.log as well as the outputof dmesg. If you are looking for something specific, I simply asked for a few lines around that message. Anyway, the relevant lines are: Relevant lines: [ 39.337207] Failed to initailize DAA, giving up... [ 39.337283] wcfxo: probe of :00:0c.0 failed with error -5 No more details. This may be a defective card. I have also seen some cases where some voodoo at the PCI layer was required (e.g: passing the boot option pci=noacpi). -- Tzafrir Cohen icq#16849755 jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users Can you find the hidden words? Take a break and play Seekadoo! Play now! http://club.live.com/seekadoo.aspx?icid=seek_wlmailtextlink ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
On Fri, Sep 07, 2007 at 12:02:29AM -0700, G B wrote: Hi, I just installed an X100p knockoff (OpenVox a100lp). I have seen my errors in the mailing list but without resolution. It seems that the . other problems had to do with IRQ sharing. Sharing IRQ lines should generally not prevent a driver from loading. It may be related to performance issues. It is also an easy target to blame performance issues for. However, it doesn't seem like the X100p is sharing an IRQ channel with anything. Any ideas? Also, I am running on Ubuntu Fiesty with Zaptel 1.4.5.1 and Asterisk 1.4.11.1. Thanks in advance. My commands below are preceded with '#' # less /etc/zaptel.conf fxsks=1 loadzone=us defaultzone=us # ztcfg -vv Zaptel Version: 1.4.5.1 Echo Canceller: MG2 Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) Ignore that message for the moment. This is from the needless automatic run of ztcfg at module probe. # dmesg | grep wcfxo [ 39.337283] wcfxo: probe of :00:0c.0 failed with error -5 Now, please look at /var/log/kern.log, or in the output of dmesg and give a number of extra lines around that. Generally the driver has failed to start using that specific card. -- Tzafrir Cohen icq#16849755jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
Sorry, I just realized that my lspci output was not verbose enough. Here is the update: # sudo lspci -vv 00:00.0 Host bridge: VIA Technologies, Inc. VT8374 P4X400 Host Controller/AGP Bridge (rev 03) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=mediumTAbort- SERR- Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=mediumTAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- # #The X100P is below # 00:0c.0 Communication controller: Motorola Wildcard X100P Subsystem: Unknown device 9085:0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=mediumTAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- _ Explore the seven wonders of the world http://search.msn.com/results.aspx?q=7+wonders+worldmkt=en-USform=QBRE ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
G B wrote: Hi, I just installed an X100p knockoff (OpenVox a100lp). I have seen my errors in the mailing list but without resolution. It seems that the other problems had to do with IRQ sharing. However, it doesn't seem like the X100p is sharing an IRQ channel with anything. Any ideas? Also, I am running on Ubuntu Fiesty with Zaptel 1.4.5.1 and Asterisk 1.4.11.1. Thanks in advance. My commands below are preceded with '#' # less /etc/zaptel.conf fxsks=1 loadzone=us defaultzone=us # ztcfg -vv Zaptel Version: 1.4.5.1 Echo Canceller: MG2 Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) # dmesg | grep wcfxo [ 39.337283] wcfxo: probe of :00:0c.0 failed with error -5 # lspci -v 00:00.0 Host bridge: VIA Technologies, Inc. VT8374 P4X400 Host Controller/AGP Bridge (rev 03) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, 66MHz, medium devsel, latency 8 Memory at d000 (32-bit, prefetchable) [size=128M] Capabilities: access denied 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: e000-e1ff Prefetchable memory behind bridge: d800-dfff Capabilities: access denied # #The X100P is below # 00:0c.0 Communication controller: Motorola Wildcard X100P Subsystem: Unknown device 9085:0001 Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at d000 [size=256] Memory at e200 (32-bit, non-prefetchable) [size=4K] Capabilities: access denied 00:10.0 USB Controller: VIA Technologies, Inc. VT82x UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at d400 [size=32] Capabilities: access denied 00:10.1 USB Controller: VIA Technologies, Inc. VT82x UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at d800 [size=32] Capabilities: access denied 00:10.2 USB Controller: VIA Technologies, Inc. VT82x UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at dc00 [size=32] Capabilities: access denied 00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 Memory at e2001000 (32-bit, non-prefetchable) [size=256] Capabilities: access denied 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, stepping, medium devsel, latency 0 Capabilities: access denied 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 18 [virtual] Memory at 01f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 03f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 0170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 0370 (type 3, non-prefetchable) [size=1] I/O ports at e000 [size=16] Capabilities: access denied 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: medium devsel, IRQ 20 I/O ports at e400 [size=256] Capabilities: access denied 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74) Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235 Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at ec00 [size=256] Memory at e2002000 (32-bit, non-prefetchable) [size=256] Capabilities: access denied 01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2) (prog-if 00 [VGA]) Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11 Memory at e000 (32-bit, non-prefetchable) [size=16M] Memory at d800 (32-bit, prefetchable) [size=128M] [virtual] Expansion ROM at e100 [disabled] [size=64K] Capabilities: access denied Does OpenVox not provide support for their hardware? Thanks,
Re: [asterisk-users] New Installed X100p
Date: Fri, 7 Sep 2007 07:13:38 -0400 From: [EMAIL PROTECTED] To: asterisk-users@lists.digium.com Subject: Re: [asterisk-users] New Installed X100p G B wrote: Hi, I just installed an X100p knockoff (OpenVox a100lp). I have seen my errors in the mailing list but without resolution. It seems that the other problems had to do with IRQ sharing. However, it doesn't seem like the X100p is sharing an IRQ channel with anything. Any ideas? Also, I am running on Ubuntu Fiesty with Zaptel 1.4.5.1 and Asterisk 1.4.11.1. Thanks in advance. My commands below are preceded with '#' # less /etc/zaptel.conf fxsks=1 loadzone=us defaultzone=us # ztcfg -vv Zaptel Version: 1.4.5.1 Echo Canceller: MG2 Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) # dmesg | grep wcfxo [ 39.337283] wcfxo: probe of :00:0c.0 failed with error -5 # lspci -v 00:00.0 Host bridge: VIA Technologies, Inc. VT8374 P4X400 Host Controller/AGP Bridge (rev 03) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, 66MHz, medium devsel, latency 8 Memory at d000 (32-bit, prefetchable) [size=128M] Capabilities: access denied 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: e000-e1ff Prefetchable memory behind bridge: d800-dfff Capabilities: access denied # #The X100P is below # 00:0c.0 Communication controller: Motorola Wildcard X100P Subsystem: Unknown device 9085:0001 Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at d000 [size=256] Memory at e200 (32-bit, non-prefetchable) [size=4K] Capabilities: access denied 00:10.0 USB Controller: VIA Technologies, Inc. VT82x UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at d400 [size=32] Capabilities: access denied 00:10.1 USB Controller: VIA Technologies, Inc. VT82x UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at d800 [size=32] Capabilities: access denied 00:10.2 USB Controller: VIA Technologies, Inc. VT82x UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at dc00 [size=32] Capabilities: access denied 00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 Memory at e2001000 (32-bit, non-prefetchable) [size=256] Capabilities: access denied 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, stepping, medium devsel, latency 0 Capabilities: access denied 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 18 [virtual] Memory at 01f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 03f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 0170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 0370 (type 3, non-prefetchable) [size=1] I/O ports at e000 [size=16] Capabilities: access denied 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: medium devsel, IRQ 20 I/O ports at e400 [size=256] Capabilities: access denied 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74) Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235 Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at ec00 [size=256] Memory at e2002000 (32-bit, non-prefetchable) [size=256] Capabilities: access denied 01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2) (prog-if 00 [VGA]) Flags: bus master, 66MHz, medium devsel, latency 32
Re: [asterisk-users] New Installed X100p
Hi Tzafrir, I am not sure what to look for, so I haveattached both the contents of /var/log/kern.log as well as the outputof dmesg. If you are looking for something specific, perhaps I can grepfor it and send you a smaller version. I have attached these as a tar ball to get below the 40K limit at which moderator approval is required. Thanks for the help. Date: Fri, 7 Sep 2007 10:26:11 +0300 From: [EMAIL PROTECTED] To: asterisk-users@lists.digium.com Subject: Re: [asterisk-users] New Installed X100p On Fri, Sep 07, 2007 at 12:02:29AM -0700, G B wrote: Hi, I just installed an X100p knockoff (OpenVox a100lp). I have seen my errors in the mailing list but without resolution. It seems that the . other problems had to do with IRQ sharing. Sharing IRQ lines should generally not prevent a driver from loading. It may be related to performance issues. It is also an easy target to blame performance issues for. However, it doesn't seem like the X100p is sharing an IRQ channel with anything. Any ideas? Also, I am running on Ubuntu Fiesty with Zaptel 1.4.5.1 and Asterisk 1.4.11.1. Thanks in advance. My commands below are preceded with '#' # less /etc/zaptel.conf fxsks=1 loadzone=us defaultzone=us # ztcfg -vv Zaptel Version: 1.4.5.1 Echo Canceller: MG2 Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) Ignore that message for the moment. This is from the needless automatic run of ztcfg at module probe. # dmesg | grep wcfxo [ 39.337283] wcfxo: probe of :00:0c.0 failed with error -5 Now, please look at /var/log/kern.log, or in the output of dmesg and give a number of extra lines around that. Generally the driver has failed to start using that specific card. -- Tzafrir Cohen icq#16849755jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _ Capture your memories in an online journal! http://www.reallivemoms.com?ocid=TXT_TAGHMloc=us dmesg-kern.tar.gz Description: GNU Zip compressed data ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] New Installed X100p
I apologize, it seems my cutting and pasting is off. The final (and correct output) of lspci -vv: 00:00.0 Host bridge: VIA Technologies, Inc. VT8374 P4X400 Host Controller/AGP Bridge (rev 03) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=mediumTAbort- SERR- Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=mediumTAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0c.0 Communication controller: Motorola Wildcard X100P Subsystem: Unknown device 9085:0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=mediumTAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- _ Discover the new Windows Vista http://search.msn.com/results.aspx?q=windows+vistamkt=en-USform=QBRE ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[asterisk-users] New Installed X100p
Hi, I just installed an X100p knockoff (OpenVox a100lp). I have seen my errors in the mailing list but without resolution. It seems that the other problems had to do with IRQ sharing. However, it doesn't seem like the X100p is sharing an IRQ channel with anything. Any ideas? Also, I am running on Ubuntu Fiesty with Zaptel 1.4.5.1 and Asterisk 1.4.11.1. Thanks in advance. My commands below are preceded with '#' # less /etc/zaptel.conf fxsks=1 loadzone=us defaultzone=us # ztcfg -vv Zaptel Version: 1.4.5.1 Echo Canceller: MG2 Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) # dmesg | grep wcfxo [ 39.337283] wcfxo: probe of :00:0c.0 failed with error -5 # lspci -v 00:00.0 Host bridge: VIA Technologies, Inc. VT8374 P4X400 Host Controller/AGP Bridge (rev 03) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, 66MHz, medium devsel, latency 8 Memory at d000 (32-bit, prefetchable) [size=128M] Capabilities: access denied 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: e000-e1ff Prefetchable memory behind bridge: d800-dfff Capabilities: access denied # #The X100P is below # 00:0c.0 Communication controller: Motorola Wildcard X100P Subsystem: Unknown device 9085:0001 Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at d000 [size=256] Memory at e200 (32-bit, non-prefetchable) [size=4K] Capabilities: access denied 00:10.0 USB Controller: VIA Technologies, Inc. VT82x UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at d400 [size=32] Capabilities: access denied 00:10.1 USB Controller: VIA Technologies, Inc. VT82x UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at d800 [size=32] Capabilities: access denied 00:10.2 USB Controller: VIA Technologies, Inc. VT82x UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at dc00 [size=32] Capabilities: access denied 00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 16 Memory at e2001000 (32-bit, non-prefetchable) [size=256] Capabilities: access denied 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, stepping, medium devsel, latency 0 Capabilities: access denied 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: bus master, medium devsel, latency 32, IRQ 18 [virtual] Memory at 01f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 03f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 0170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 0370 (type 3, non-prefetchable) [size=1] I/O ports at e000 [size=16] Capabilities: access denied 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50) Subsystem: Elitegroup Computer Systems Unknown device 0a82 Flags: medium devsel, IRQ 20 I/O ports at e400 [size=256] Capabilities: access denied 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74) Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235 Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at ec00 [size=256] Memory at e2002000 (32-bit, non-prefetchable) [size=256] Capabilities: access denied 01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2) (prog-if 00 [VGA]) Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11 Memory at e000 (32-bit, non-prefetchable) [size=16M] Memory at d800 (32-bit, prefetchable) [size=128M] [virtual] Expansion ROM at e100 [disabled] [size=64K] Capabilities: access denied _ News, entertainment and everything you care about at Live.com. Get it now!
Re: [asterisk-users] New Installed X100p
On Fri, Sep 07, 2007 at 08:45:11AM -0700, G B wrote: Hi Tzafrir, I am not sure what to look for, so I haveattached both the contents of /var/log/kern.log as well as the outputof dmesg. If you are looking for something specific, I simply asked for a few lines around that message. Anyway, the relevant lines are: Relevant lines: [ 39.337207] Failed to initailize DAA, giving up... [ 39.337283] wcfxo: probe of :00:0c.0 failed with error -5 No more details. This may be a defective card. I have also seen some cases where some voodoo at the PCI layer was required (e.g: passing the boot option pci=noacpi). -- Tzafrir Cohen icq#16849755jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ Sign up now for AstriCon 2007! September 25-28th. http://www.astricon.net/ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
