I have 2 questions:
1. Can I make outbound route rule based on the Source Channel?
2. Can I auto change the outbound route based on time/Day of week?
Any help very appreciated..
___
-- Bandwidth and Colocation Provided by
--
Sent from mobile device
On Nov 8, 2009, at 2:13 PM, B.Masoud @ SH i...@saudihome.com wrote:
I have 2 questions:
1. Can I make outbound route rule based on the Source Channel?
Yes.
2. Can I auto change the outbound route based on time/Day of
week?
Yes. See
Discussion
Cc: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] outbound routing
--
Sent from mobile device
On Nov 8, 2009, at 2:13 PM, B.Masoud @ SH i...@saudihome.com wrote:
I have 2 questions:
1. Can I make outbound route rule based on the Source
Sent: Sunday, November 08, 2009 10:24 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Cc: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] outbound routing
--
Sent from mobile device
On Nov 8, 2009, at 2:13 PM, B.Masoud @ SH i
Dear All,
I have a small call center in which I have to define least cost routing for
outbound calls. For now I have always done this by routing numbers to different
providers according to the number prefix.
However, a new law became effective now which allows people to switch between
If it's anything like the UK, it won't make a difference... for example:
o2 mobile number ported to orange mobile...
On most providers you still pay the o2 rate.
three mobile ported to o2...
you still pay the three rate (which isn't so good since it's far more
expensive than o2).
Cheers
Alex, What country is your call center located?
Thanks,
Al
On Fri, Mar 13, 2009 at 7:36 AM, Asterisk aster...@abraxas.si wrote:
Dear All,
I have a small call center in which I have to define least cost routing for
outbound calls. For now I have always done this by routing numbers to
Hello,
I have a TDM400 and currently have 2 of the ZAP Trunks configured
on it. Zap/1-1 and Zap/2-1. I am Running [EMAIL PROTECTED] Version 2.4
with AMP version 1.10.010
In my Outbound Routing I have the Trunk Sequence set up so that 0 is
Zap/1-1 and 1 is ZAP/2-1 What I see is that
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of
Nate List
Sent: Tuesday, February 21, 2006 7:17 PM
...
In my Outbound Routing I have the Trunk Sequence set up so that 0 is
Zap/1-1 and 1 is ZAP/2-1 What I see is that when Trunk
Sequence 0 is
Mimmus, It looks like this took care of the problem.
Thanks for your help,
Nate
Mimmus wrote:
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]] On Behalf Of
Nate List
Sent: Tuesday, February 21, 2006 7:17 PM
...
In my Outbound Routing I have the Trunk
Hi all, I've 3 providers (A, B, and C) the A is giving me freecalls to
USA, the B is giving my freecalls to Europe, and C is to call the otre
destinations. My question is, how can I configure the outboud routing to
select the right trunk for every destination?
All the providers uses the dialing
: [Asterisk-Users] Outbound routing
Hi all, I've 3 providers (A, B, and C) the A is giving me freecalls to USA,
the B is giving my freecalls to Europe, and C is to call the otre
destinations. My question is, how can I configure the outboud routing to
select the right trunk for every destination?
All
can't you ask the users to dial a prefix? that can solve your problem. btw, which provider are you using for your calls to the USA? Alyed Return-Path: [EMAIL PROTECTED] Wed Jan 11 09:47:29 2006Received: from digium-69-16-138-164.phx1.puregig.net [69.16.138.164] by mail11.webcontrolcenter.com with
Hello,
I have a 4 port FXO digium card with 3 PSTNs attached to it
and AsteriskAtHome setup. Everything is working fine except outbound calls.
When I dial a outside number, it works fine, but when
another employee trys to dial out while I am on a line, it will not go.
I have a
14 matches
Mail list logo