On Mon, Mar 17, 2014 at 10:25:59PM +, Cristiano De Alti wrote:
> Alexander Aring writes:
>
> >
> > Hi,
> >
> > just an idea... don't asking about why. But can you please disable
> >
> > ARM_OPTIMZED_STRING_FUNCTIONS
> >
> > and test it again? I will check something there...
> >
> > - Ale
On 17/3/14 6:53 PM, Sascha Hauer wrote:
> On Mon, Mar 17, 2014 at 03:44:15PM +0800, Sean Cross wrote:
>> On 17/3/14 3:18 PM, Sascha Hauer wrote:
>>> On Mon, Mar 17, 2014 at 12:28:28PM +0800, Sean Cross wrote:
Here is the resulting output and BUG from this run:
barebox 2014.03.0-00628
Alexander Aring writes:
>
> Hi,
>
> just an idea... don't asking about why. But can you please disable
>
> ARM_OPTIMZED_STRING_FUNCTIONS
>
> and test it again? I will check something there...
>
> - Alex
>
I've disabled the above CONFIG in Barebox and I don't see any difference in
the durat
Sascha Hauer writes:
>
> On Thu, Mar 13, 2014 at 08:44:08PM +, Cristiano De Alti wrote:
> > Hi,
> > I'm probably posting to the wrong list since this is Linux issue.
> > I'm still trying to revive this old board.
> >
> > This board has a 64MBi Samsung NAND flash that is detected both by B
Thanks for the reply. So I take it I need to edit the mux.c file in the
PCM049(which is the one I use) board directory. I changed the lines as
below:
{I2C4_SDA, (PTU | IEN | M0)}, /* i2c4_sda */
{MCSPI1_CLK, (M3)}, /* gp
Hi Christian,
On Mon, Mar 17, 2014 at 12:00:52PM +0100, Christian Hemp wrote:
> Hello Sascha,
>
> We removed this ODT values, because we had problems. I think before we
> use this settings we have to do some tests (climate cabinet...) with
> different modules.
Ok, I'll drop the patch then.
Sasc
On Mon, Mar 17, 2014 at 10:47:06AM +0200, Ivor Kruger wrote:
> Hi, sure this is a quick and easy question for the group
>
> On the OMAP4430, using the command from within barebox prompt to configure
> a GPIO for testing hardware:
>
> gpio_direction_output 140 0
>
> Should this be sufficient to
Hello Sascha,
We removed this ODT values, because we had problems. I think before we
use this settings we have to do some tests (climate cabinet...) with
different modules.
Christian
Am Freitag, den 14.03.2014, 14:30 +0100 schrieb Sascha Hauer:
> From: Christian Hemp
>
> Change the ODT values
On Mon, Mar 17, 2014 at 03:44:15PM +0800, Sean Cross wrote:
> On 17/3/14 3:18 PM, Sascha Hauer wrote:
> > On Mon, Mar 17, 2014 at 12:28:28PM +0800, Sean Cross wrote:
> >> Here is the resulting output and BUG from this run:
> >>
> >> barebox 2014.03.0-00628-g7fed07d-dirty #158 Mon Mar 17 12:25:45 SG
This driver is very handy for initial barebox porting.
It was used for running barebox on DiGiC2-based camera
and initial porting barebox to Loongson-1 and ar9331.
Signed-off-by: Antony Pavlov
Signed-off-by: Sascha Hauer
Reported-by: Alexander Aring
Reported-by: Alexander Shiyan
---
drivers/c
Hi, sure this is a quick and easy question for the group
On the OMAP4430, using the command from within barebox prompt to configure
a GPIO for testing hardware:
gpio_direction_output 140 0
Should this be sufficient to set the gpio pin low, or is it required to
still do some pin muxing as well?
On 17/3/14 3:18 PM, Sascha Hauer wrote:
> On Mon, Mar 17, 2014 at 12:28:28PM +0800, Sean Cross wrote:
>> Here is the resulting output and BUG from this run:
>>
>> barebox 2014.03.0-00628-g7fed07d-dirty #158 Mon Mar 17 12:25:45 SGT 2014
>>
>>
>> Board: Kosagi i.MX6DL Novena Board
>> detected i.MX6 D
On Mon, Mar 17, 2014 at 08:18:58AM +0100, Sascha Hauer wrote:
> On Mon, Mar 17, 2014 at 12:28:28PM +0800, Sean Cross wrote:
> > Here is the resulting output and BUG from this run:
> >
> > barebox 2014.03.0-00628-g7fed07d-dirty #158 Mon Mar 17 12:25:45 SGT 2014
> >
> >
> > Board: Kosagi i.MX6DL N
On Fri, Mar 14, 2014 at 06:11:16PM +0100, Jean-Christophe PLAGNIOL-VILLARD
wrote:
> On 11:11 Fri 14 Mar , Sascha Hauer wrote:
> > the splash command silently fails when no renderer is found for
> > an image type. Print an error message in this case.
> >
> > Signed-off-by: Sascha Hauer
> > --
On Mon, Mar 17, 2014 at 12:28:28PM +0800, Sean Cross wrote:
> Here is the resulting output and BUG from this run:
>
> barebox 2014.03.0-00628-g7fed07d-dirty #158 Mon Mar 17 12:25:45 SGT 2014
>
>
> Board: Kosagi i.MX6DL Novena Board
> detected i.MX6 DualLite revision 1.1
> Trying to request regio
On Sun, Mar 16, 2014 at 12:27:24PM +0400, Alexander Shiyan wrote:
> To ease DT import from Linux, which is still maintained in-tree, we
> separate barebox-specific changes by including the original dts in
> a separate DT file. This allows to overlay modifications and keep
> clean DT history. Additi
16 matches
Mail list logo