Hi,
Sorry I am new to this. I could not find my question in the forum
Where can I find it?
Do I need to resend again?
Thanks in advance
Boh Lim
On Wed, Aug 1, 2018 at 6:48 PM, wrote:
>
> Hi,
>
> I just bought two BBB Wireless boards.
> The default image, Debian version is 8.6 - I am able
UPDATE: the pull-up resistor didn't help.
I tried a new BBB. It exhibited the same behavior, powered by USB or the DC
jack.
Since I'm running headless, I set multi-user.target and then apt-get remove
-y x11-common.
This freed 370MB.
It also had the side effect of changing the power off
On Thu, Aug 2, 2018 at 5:24 PM, wrote:
> Even I have the same problem, did you figure out why?
You need v4.13.x+
https://elinux.org/Tests:MSIOF-SPI-Slave
My ISP in the US runs IP4 and releases every 2 mins, and IPv6 runs fine
with out issue.
At first the printer did not work and other things but it is all good now.
Except for the Beagle Board Blue. I load the SD, and the light shows up,
and repeats it self in the middle of the blue led
Even I have the same problem, did you figure out why?
On Monday, November 6, 2017 at 9:57:17 AM UTC-6, simo zz wrote:
>
>
> Hello,
>
> I am developing a C application to read from the SPI0 from the Beaglebone
> Black.
>
> The test I am doing is with two Beaglebones, one configured as a slave
>
Hello,
Any luck on this? I have the same issue.
On Saturday, April 12, 2014 at 3:39:58 AM UTC-5, Babak Rezai wrote:
>
> Im trying to use the Beaglebone Black as a slave device and read from the
> arduino over SPI.
>
> Im confused as to why I am just getting 255 repeated over and over on the
>
Hello There,
I need some help on connecting BeagleBone WL1835MOD w/ Chip Antenna Cape
rev A1 on BeagleBone white A6.
Here is the log from dmesg;
debian@beaglebone:~$ sudo dmesg | grep cap
[sudo] password for debian:
[0.806505] Linux video capture interface: v2.00
[1.699523]
Thanks Robert!!
Would really like to test the 485 mode in the 8250 driver, but before that,
we're going to try to get 485 mode enabled on the FTDI FT4232 USB<->serial
hub. We've ordered some FT4232 Mini Module evaluation boards for FT4232
(FT4232H chip + EEPROM + breakout pins + mini USB
Thanks Robert!!
Would really like to test the 485 mode in the 8250 driver, but before that,
we're going to try to get 485 mode enabled on the FTDI FT4232 USB<->serial
hub. We've ordered some FT4232 Mini Module evaluation boards for FT4232
(FT4232H chip + EEPROM + breakout pins + mini USB
http://bit.ly/AMAZONSupport
Amazon Launch Its New Contact #Number Toll-free To Connect With Their
Customer Easily So If You Have Any Query Now You Can tell it Directly To
Amazon or If You Are Trouble With any #problem Then Get It Instant
Sollution By #Amazon Certifired Technicians For Free
On Thu, Aug 2, 2018 at 8:22 AM Jeff Andich wrote:
>
> Hi,
>
> What's the best way to find out how long a legacy driver like the omap-serial
> driver will be supported in the kernel going forward?
It's not going anywhere till they are feature matching..
>
> We've swapped out the 8250 driver for
Hi,
What's the best way to find out how long a legacy driver like the
omap-serial driver will be supported in the kernel going forward?
We've swapped out the 8250 driver for the OMAP serial driver via the
.config file, since the omap serial driver implements a 485 mode which,
thus far,
Hi
I find my mistake : I forget the driver "AMx3 Power management" into soc
section.
Now I can pass my bord into standby mode.
But now, I have a probleme if I switch the board in to standby mode with
usb otg connected to a PC it fail with a kernel panic into the usb core
driver.
Philippe
13 matches
Mail list logo