Hello community,

I use the Angström Image v2012.12 - Kernel 3.8.13 with U-Boot SPL 
2013.04-dirty (Jun 19 2013 - 09:57:14) and I can login on my BBB. 

I also try to run a custom board similar to the BBB. I only removed the 
HDMI part and use a MT41K256M16TW-107 ITP DDR3. When I try to boot, it 
stops while running the kernel:

Code hier eingeben...
U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, 
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, 
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img


U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14)

I2C:   ready
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  No NAND device found!!!
0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, 
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, 
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot:  0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
33 bytes read in 3 ms (10.7 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
gpio: pin 55 (gpio 55) value is 1
4270840 bytes read in 770 ms (5.3 MiB/s)
gpio: pin 56 (gpio 56) value is 1
24129 bytes read in 49 ms (480.5 KiB/s)
Booting from mmc ...
## Booting kernel from Legacy Image at 80007fc0 ...
   Image Name:   Angstrom/3.8.13/beaglebone
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4270776 Bytes = 4.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 80f80000
   Booting using the fdt blob at 0x80f80000
   XIP Kernel Image ... OK
OK
   Using Device Tree in place at 80f80000, end 80f88e40

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.194444] omap2_mbox_probe: platform not supported
[    0.204990] tps65217-bl tps65217-bl: no platform data provided
[    0.281512] bone-capemgr bone_capemgr.8: slot #0: No cape found
[    0.318618] bone-capemgr bone_capemgr.8: slot #1: No cape found
[    0.355726] bone-capemgr bone_capemgr.8: slot #2: No cape found
[    0.392836] bone-capemgr bone_capemgr.8: slot #3: No cape found
[    0.412862] bone-capemgr bone_capemgr.8: slot #6: BB-BONELT-HDMIN 
conflict P8                                   .45 (#5:BB-BONELT-HDMI)
[    0.422487] bone-capemgr bone_capemgr.8: slot #6: Failed verification
[    0.429266] bone-capemgr bone_capemgr.8: loader: failed to load slot-6 BB
-BON                                   ELT-HDMIN:00A0 (prio 2)
[    0.451930] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' 
failed
[    0.516301] pinctrl-single 44e10800.pinmux: pin 44e10854 already 
requested by                                    44e10800.pinmux; cannot 
claim for gpio-leds.7
[    0.528016] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.7) status -
22
[    0.535334] pinctrl-single 44e10800.pinmux: could not request pin 21 on 
devic                                   e pinctrl-single
[    0.568496] dummy 0-0034: Error -121 writing to cec:0xff
[    0.574309] tda998x 0-0070: Error -121 reading from 0xa
[    0.580038] tda998x 0-0070: Error -121 writing to 0xa
[    0.637061] tda998x 0-0070: Error -121 reading from 0xa
[    0.642639] tda998x 0-0070: Error -121 writing to 0xa
[    0.699595] tda998x 0-0070: Error -121 reading from 0x1
[    0.705172] tda998x 0-0070: Error -121 writing to 0x1
[    0.710564] tda998x 0-0070: Error -121 reading from 0x1
[    0.716136] tda998x 0-0070: Error -121 writing to 0x1
[    0.721524] tda998x 0-0070: Error -121 writing to REG_CURPAGE
[    0.727640] tda998x 0-0070: Error -121 writing to 0x200
[    0.733211] tda998x 0-0070: Error -121 writing to 0x201
[    0.738781] tda998x 0-0070: Error -121 writing to 0x202
[    0.744377] tda998x 0-0070: Error -121 writing to 0x203
[    0.749949] tda998x 0-0070: Error -121 writing to 0x204
[    0.755520] tda998x 0-0070: Error -121 writing to 0x205
[    0.761090] tda998x 0-0070: Error -121 writing to 0x20e
[    0.766661] tda998x 0-0070: Error -121 writing to 0x211
[    0.772233] tda998x 0-0070: Error -121 writing to 0x207
[    0.777803] tda998x 0-0070: Error -121 writing to 0x208
[    0.783372] tda998x 0-0070: Error -121 writing to 0x209
[    0.788942] tda998x 0-0070: Error -121 writing to 0x20a
[    0.794514] tda998x 0-0070: Error -121 writing to 0x206
[    0.800084] tda998x 0-0070: Error -121 writing to REG_CURPAGE
[    0.806199] tda998x 0-0070: Error -121 reading from 0x0
[    0.811770] tda998x 0-0070: Error -121 reading from 0x2
[    0.817608] tilcdc 4830e000.fb: no encoders/connectors found
[    0.823568] tilcdc 4830e000.fb: failed to initialize mode setting



Could the different RAM be the reason for this? Could anybody give an 
advice to get it run?
Thank you very much.

Best regards
Eric

-- 
For more options, visit http://beagleboard.org/discuss
--- 
You received this message because you are subscribed to the Google Groups 
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to beagleboard+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/beagleboard/79c1dc68-0683-4cf2-a354-0a3000022852%40googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Reply via email to