I have five 7961 phones and a four 7941 phones in my lab. Is there anything
deeming in the workbooks that would require me to have all six-line phones
or is it ok to have a mix? I didn¹t see anything in the lab topology that
indicates the specific models of phones.
Thanks,
Mark
Hi Zamuel,
Have you issue the command "ccm-manager music-on-hold" command on the
voice gateway? This command is needed in order for the voice gateway
to successfully receive multicast MoH as instructed by the UCM.
Cheers,
Danny
zamuel del Toro wrote:
I have a phone on hq site calling to
Hi All,
please provide some help.
I'm just posting this questions to both forums as its related to both. In
hope to get some help on below issue:
Asterisk 1.4.x
CCM = 4.x
CME = 4.x
codec = g711ulaw
Here is my setup:
600X Phones Asterisk SIP Trunk Call Manager - CME
-
Hi Jeremy,
Have you tried to issue the command ccm-manager music-on-hold on the
voice gateway? It is needed in order for the voice gateway to receive
mcast MOH from UCM.
Cheers,
Danny
jeremy co wrote:
Hi,
unicast -HQ
Multicast-BR1 -MOH from flash 239.1.1.1, internal phones play moh
Hi List,
is cRTP in combination with MLPPP supported? Where can i find some
documenatation about this? I searched on CCO, but i did not find anything
meaningful to me.
If cRTP is supported, should i enable it in a MQC Class or under the
virtual-template interface?
Any hints are welcome!
It's in the QoS SRND, page 3-17. ALL the SRNDs are worth reading cover to
cover at least 10 times. For v2 studying, even reading parts of the 7.x SRNDs,
the language is clearer, better examples, etc than the 4.x SRNDs.
Slow-Speed (£768 kbps) Leased Lines
Recommendation: Use MLP LFI and cRTP.
I don't know if this will be different in the V3 IOS, but I recently found that
when I invoked cRTP on a link carrying SIP to CCM, DTMF stopped working.
Apparently the NTE designation is carried in the RTP header and is not
reconstituted correctly under cRTP when it is
In Lab 5a, working with Device Mobility, at the end of 5.17 (immediately before
the Solution and Explanation), there is a bullet point saying Add a Calling
Number Transformation Pattern that is visible to the HQ Device Pool. I'm
assuming that is the 1XXX we created previously back in 5.16,
Hi,
regarding the CCM 4.1 SRND on Page 8-27, an GK controlled ICT should be used to
connect an CCM with an CME.
• Configure a gatekeeper-controlled intercluster trunk (ICT) on Cisco
CallManager.
Cisco CallManager registers with the gatekeeper through the ICT, and CME
registers with the
Hi,
I have BACD setup with the drop-through-option. After call to hunt-pilot,
bacd hunts for the two members of hunt list and when noans go to GDM. Call
is recorded correctly. CUE voicemail mailbox shows the msgs counter
incremented.
However when I try to call the voicemail from either of the
That will do you just fine. You should be able to everything we post
with that mixture of phones.
--
Mark Snow
CCIE #14073 (Voice, Security)
Senior Technical Instructor - IPexpert, Inc.
Telephone: +1.810.326.1444
Fax: +1.309.413.4097
Mailto: ms...@ipexpert.com
--
Join our free online support
Hi John,
you should check GDM messages when you logged in to member Phone VM ,after
that go to option 9 for GDM messages.
Cyrus
On Fri, May 22, 2009 at 9:33 AM, john D jkd1...@gmail.com wrote:
Hi,
I have BACD setup with the drop-through-option. After call to hunt-pilot,
bacd hunts for the
Hi Cyrus
Thanks for your email.
It worked..
J
On Thu, May 21, 2009 at 5:13 PM, Cyrus cyrus@gmail.com wrote:
Hi John,
you should check GDM messages when you logged in to member Phone VM ,after
that go to option 9 for GDM messages.
Cyrus
On Fri, May 22, 2009 at 9:33 AM, john D
I use a mixture of phones as well. Have not run into any problems at all.
You'll be fine.
Larry Hadrava
CCIE #12203 CCNP CCNA
Sr. Support Engineer – IPexpert, Inc.
URL: http://www.IPexpert.com
On Thu, May 21, 2009 at 7:52 PM, Mark Snow ms...@ipexpert.com wrote:
That will do you just fine.
Hi,
I'm trying to enable on hook transfer at CME.
Does someone know a way to do that?
E.g.
A calls B
B answers
B press transfer and calls C
B talks to C
B hung up and A is connected to C.
Thanks in advance, Sergio.
_
Novo
Sounds like you are looking to do a consultative transfer.
telephonyservice
transfer transfer-system full-consult
This should be the default action.
correct me if my understanding of the requirement is incorrect.
Larry Hadrava
CCIE #12203 CCNP CCNA
Sr. Support Engineer – IPexpert, Inc.
URL:
16 matches
Mail list logo