Earlier this week, I began Vol 2 Lab 1. In this lab, I configured
transcoding resources on the CUBE. These resources were registered to
the gateway itself, under telephony-service.
I was messing around on a router this morning and found something
confusing. If I define "maximum sessions"
Hi Vik:
So in your opinion, troubleshooting will gain weight in the lab section, but
not so far as in RS in wich you have separate troubleshooting section
Thanks
Date: Thu, 6 May 2010 11:32:56 -0700
From: vma...@ipexpert.com
To: siddas...@gmail.com; tanner.ez...@gmail.com
CC:
I think the number 90 was not b/c 45 (dspfarm) + 45 (sdspfarm), you had a
value of 90 because each transcoder session consists of two transcoding
streams between callers using transcode.
Bo
On Fri, May 7, 2010 at 3:33 AM, Matthew Berry ciscovoiceg...@gmail.comwrote:
Earlier this week,
Hi Segio
Yes it is confusing isn't it. The columns represent the number of packets per
dscp value. As an example there are 133518 packets in the best effort class
(dscp 0) and 34243 packets marked with dscp 24. There are also 40177 voice
packets, dscp value 46.
Regards
Peter
From: Sergio
Bo -
You're right. I changed the max sessions value from 45 to 2. This is the
new output from my show sdspfarm units:
mtp-1 Device:RTR-XCODE TCP socket:[1] REGISTERED in SCCP ver 17/10
actual_stream:4 max_stream 4 IP:192.168.99.1 57105 MTP Dixieland keepalive 0
Supported codec:
Matthew,
MTP Dixieland is the hardware reference:
MODEL_DIXIELAND_CFB = 52, // Cisco IOS Conference Bridge (HDV2)
MODEL_DIXIELAND_SW_MTP = 83, // Cisco IOS Media Termination Point (HDV2)
MODEL_DIXIELAND_MTP = 112, // Cisco IOS Media Termination Point (HDV2)
On older equipment:
Can any one answer my question?
thank you
On 05/06/2010 11:37 PM, kerboute kerboute wrote:
Hi guys,
Can I use a cisco 837 router to setup VPN with Proctors Voice vRack?
Regards
Naoufal
___
For more information regarding industry leading CCIE
I believe you can, but you might want to run you question by
supp...@ipexpert.com to be 100% certain.
Roger Källberg
Consultant
Cygate AB
Från: kerboute kerboute [naoufal.kerbo...@cbi.ma]
Skickat: den 7 maj 2010 16:56
Till: ccie_voice@onlinestudylist.com
You should be able to with the right IOS and tweaking the interfaces in the
config file from IPX.I'm using 1861 with a single fastethernet port so I've
done sub interfaces and vlans and it works.
-Original Message-
From: ccie_voice-boun...@onlinestudylist.com
MAC seems to be wrong.
On Fri, May 7, 2010 at 5:01 AM, Ashar Siddiqui siddas...@gmail.com wrote:
Try the new CIPC version 7.0.3.0 as the previous one had this problem.
Ash
vccie2010 wrote:
Tried with no-auto-reg too but no luck... Hope it is clear (:-
here is my config...
I do have CIPC ver 7.0.3.0 please...
On Thu, May 6, 2010 at 8:03 PM, vccie2010 vccie2...@gmail.com wrote:
Tried with no-auto-reg too but no luck... Hope it is clear (:-
here is my config...
telephony-service
no auto-reg-ephone
max-ephones 2
max-dn 4
ip source-address 10.10.202.1
Now is Official: http://www.cisco.com/web/learning/le3/ccie/voice/lab_exam.html
Update to the CCIE Lab Question Format
Beginning May 10, 2010, CCIE Voice lab exams
in all global locations will no longer include the four, open-ended Core
Knowledge questions. The total
Dear,
in this lab section we should add BR1-RTR as an MGCP gateway.
I made the configuration AS Proctorlab guide and I got gateway register (sh
ccm-manager)
But when I (debug isdn q931) nothing appeared (I dialed as match as the
Route Pattern)
I attach the BR1 Configuration
Please advice
Do a show isdn status.
If you don't see MULTIPLE_FRAME_ESTABLISHED state under Layer 2 Status,
then do a no isdn bind-l3 ccm-manager command under interface
Serial0/0/0:23, wait a few seconds, then put the bind-l3 command back.
I find this usually works (much faster than reloading the
Hello,
My PSTN phone for lab 8 vol 2 is not registering
Any one with similar issue
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
If you reset the gateway and no mgcp, mgcp and still face the problem,
reload the router. I get that all the time and I simply reload the router
and it works
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of amr gaber
Sent: Friday, May
16 matches
Mail list logo
