Hi Prashant,
I'll try this scenario you just mention and i'll let you know :)
Best regards,
Amr Sherif
Date: Fri, 12 Nov 2010 11:26:30 -0500
Subject: Re: [OSL | CCIE_Voice] MVA Call Drops
From: prashantpatel...@gmail.com
To: miroale...@hotmail.com
CC: anil...@yahoo.com;
7 digit or more dialing, Can answer or hang up calls with local IP phones.
Hi all,
I am using 7962 7961 phones locally to me. All firmware has been upgraded to
what is on the
Vrack.
Connected via a 871 and 3560 POE switch.
The 3560 is a dumb switch. Support recommended I should run it with
Hi Experts,
while practicing volume 1 lab 5.9: block 91900? pattern for all phones. ? wild
card has no effect if the number is not consecutive
zeros after 91900 digit string.
CUCM help says: The route pattern 91X? routes or blocks all numbers in the
range 91 through 919.
Mudassar,
Which wildcard did you use? 91X will block any number from 91[0 thru 9].
Actually this wouldn't let you type any 4th digit since it is the closest
match when dialing a 900 numbers.
To block 900 numbers; I would use the device-line CSS approach with RP
91900XXX in partition blocked
please configure an incoming voip dial peer
on the HQ router and BR1
that will resolve your problem
2010/11/14 Michael Murphy matin_...@yahoo.com
7 digit or more dialing, Can answer or hang up calls with local IP phones.
Hi all,
I am using 7962 7961 phones locally to me. All firmware has
helloo all
I'm working on Workbook 1 Lab 9A
on EM for CUCME
i have this problem
when i configure the logout profile
and apply it to my 7970
it will take it and it will register, however no extension is displayed
the same happened to me with a CIPC and a 7962
when i log in to EM i have the
Hi Cristobal,
Make sure you create the ephone-dn you are using in the logout profile.
HTH
Prashant
On Sun, Nov 14, 2010 at 3:21 PM, Cristobal Priego cristobalpri...@gmail.com
wrote:
helloo all
I'm working on Workbook 1 Lab 9A
on EM for CUCME
i have this problem
when i configure the
thank you that was my mistake
one more question when you're on em how do you log out ?
2010/11/14 Prashant Patel prashantpatel...@gmail.com
Hi Cristobal,
Make sure you create the ephone-dn you are using in the logout profile.
HTH
Prashant
On Sun, Nov 14, 2010 at 3:21 PM, Cristobal
Hi Cristobal,
under service button you should see a logout option. This will need the ip
http server command and the tftp path flash:/gui.
HTH
Prashant
On Sun, Nov 14, 2010 at 3:28 PM, Cristobal Priego cristobalpri...@gmail.com
wrote:
thank you that was my mistake
one more question when
thank you very much Prashant
2010/11/14 Prashant Patel prashantpatel...@gmail.com
Hi Cristobal,
under service button you should see a logout option. This will need the ip
http server command and the tftp path flash:/gui.
HTH
Prashant
On Sun, Nov 14, 2010 at 3:28 PM, Cristobal Priego
Hi all
I going crazy trying to figure out this issue. I use a Hardware VPN to connect
to PL
with 7960 and 7961 phones. I am doing LAB 10A part 10.1 RSVP call agent.
I have BR1 to HQ set to Manadtory under the Locations in CUCM and have all the
DP settings and MRG and MRGL's as per the PG
Heres a hint. Read the qos srnd. Some WAN qos mechanisms are incompatible
with ip rsvp. If I recall, the point of this lab is to teach you this lesson
at the cost of your time and frustration.
- Reply message -
From: Stern, Larry larry.st...@nuvt.com
Date: Sun, Nov 14, 2010 3:54 pm
Anybody know how to contact ProctorLabs After-Hours Support if you're not in
a current rack session? I had sessions scheduled for today that are no
longer scheduled. And of course, I can't schedule now since it's past the
start time.
My lab exam is tomorrow... Just wanted to run through a few
Hi Scott,
Try emailing supp...@ipexpert.com
And best of luck on your lab!
cheers, sd
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Scott
Newberry
Sent: Sunday, November 14, 2010 4:23 PM
To: osl osl
Subject: [OSL |
HI
I am working on lab 10 wb 1
I am getting this error on the HQ router when applying auto qos to the DLCI for
br1
Nov 15 04:41:49.345: %RMON-5-FALLINGTRAP: Falling trap is generated because
the value of cbQosCMDropBitRate.354.12774241 has fallen below the
falling-threshold
good luck I hope you do well in your lab!
Thanks,
Matthew Berry
Sent from my Verizon Wireless Phone. Please excuse brevity and any typo errors.
- Reply message -
From: Scott Newberry sc...@meganandscott.com
Date: Sun, Nov 14, 2010 3:26 pm
Subject: [OSL | CCIE_Voice] Support Needed!
To:
Hi
I run the auto QoS command on the hq router fine for the interface towards br2.
When I run auto QoS for the interface for br1 it runs but does not create the
policy map or class map.
Has anyone seen this issue?
Thanks
Randall
Sent from my iPhone
On Nov 14, 2010, at 3:47 PM, Randall
When I was using the remote racks back in the summer, there was a known issue
when using auto QOS on their equipment due to IOS version mismatch on the
Proctor Labs gear. Do a show version to check.
Thanks,
Matthew Berry
Sent from my Verizon Wireless Phone. Please excuse brevity and any typo
Hi Steve,
I am working on the same thing. Assuming RSVP that it was working before
WAN MLP was configured, please check a couple of things:
1) the ip rsvp bandwidth XYZ is configured under interface virtual-template
2) the IOS version of your routers.
#2 was the reason why mine was not
Thanks Matt but the issue is occurring on the hq rtr when u run auto QoS on the
2nd interface dlci. The first one works fine
Randall
Sent from my iPhone
On Nov 14, 2010, at 7:20 PM, Matthew Berry matthew.be...@cdw.com wrote:
When I was using the remote racks back in the summer, there was a
Hi
I checked the hq iOS and it was like 12.4.15. I tried the br1 rtr, iOS v.
12.4.2x and it worked. So maybe it is the iOS version on the hq rtr.
Another guy was having a similar issue tonight as well
Thanks
Randall
Sent from my iPhone
On Nov 14, 2010, at 7:24 PM, Rrcrumm rrcr...@yahoo.com
21 matches
Mail list logo