Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

yes both only if that router is an NTP master, otherwise CUE will ignore it i've tested this scneario multiple times and connectivity is not an issue your router could receive time form the pstn: ntp server 10.10.100.2 and if you want it to provide clocking to your netowrk devices you must make

[OSL | CCIE_Voice] CME octo line functionality

Hello all, I've been reading the blog about octo lines on cme however i still doesn't clearly understand how the max-calls-per-button and busy-trigger-per-button work and it's correlation to shared lines could you point me to a document or if you could, please explain that to me? I'd really apprec

[OSL | CCIE_Voice] AAR for TEHO call

hi , - AAR will not work for TEHO ,right ? ( when we in AAR situatuin, will the call come out thru other GW ie : HQ and SC in AAR mode, and for 900.! --> RL- HQ-SC , when go thru SC will work or not ? ) ___ For more information regarding

Re: [OSL | CCIE_Voice] SRST - "Phones should work same as it isregistered with CUCM"

shared line same behaviour as main line , call to CUE from PSTN (in case of JTAPI after back from SRST)have to come in to UCM first (not CUE directly) softkey most same, but some condition in SRST is diferent. On Sun, Jun 19, 2011 at 6:42 AM, Victor Malyuga wrote: > max-calls-

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

Hi All, Thanks for your suggestions and explanations. I have the Route command in place on the CME router in order to achieve reachability to the CUE module. I am able to ping the CUE IP from the HQ router so i doubt if routing could be the problem. In the lab exam if i am asked to sync my CU

Re: [OSL | CCIE_Voice] VMware ESXi for CCM servers

I am running my CUCM Pub/Sub, CUPS and CUC all version 7 on a single intel quad core with 8 GB ram. I have found that if the VM's have their own HDD they perform much better. On Mon, Jun 27, 2011 at 4:25 PM, Michael Thompson wrote: > Make sure you're installing on an intel CPU.  Had major issues

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

I have tested this with routers but not with the CUE module. Routers will definitely pull their time from a router synced with another NTP source. On Mon, Jun 27, 2011 at 4:55 PM, Alan Gardner wrote: > According to Vik you do not need the NTP Master. > > > > Try doing a no shut in the Service mo

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

you need the ntp master command on the router with the proper stratum set otherwise when you go through the cue initialization and you enter the router's loopback it;s going to say not reachable and is going to ask for a different ntp server 2011/6/27 Alan Gardner > According to Vik you do not n

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

Sandeep; Maybe you already have this, but just to check Make sure you have the static route to your CUE module IP Address on the BR2 router. b/c most of the time when CUE can't access the ip address of the PSTN or HQ router, meant I forgot the route statement. >From HQ can you ping CUE and the oth

Re: [OSL | CCIE_Voice] MLS QoS issue

Did you need this? ipt-switch#sh mls qos interface f0/3 FastEthernet0/3 trust state: trust dscp trust mode: trust dscp trust enabled flag: ena COS override: dis default COS: 0 DSCP Mutation Map: Default DSCP Mutation Map Trust device: none qos mode: port-based From: Cristobal Prieg

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

According to Vik you do not need the NTP Master. Try doing a no shut in the Service module interface!!! Best Regards, Alan Gardner Chief Executive Officer Current Technologies Computer Learning Center PH. 219.764.3800 agard...@ctclc.com MCT, MCSE (Messaging & Security)

Re: [OSL | CCIE_Voice] MLS QoS issue

the output doesn't show anything like that you only only posted mls qos map cos-dscp 0 8 16 24 32 46 48 56 which means CS 0 will be mapped to dscp 0 CS 1 to dscp 8 CS 2 to dscp 16 CS 3 to dscp 24 CS 4 to dscp 32 CS 5 to dscp 46 CS 6 to dscp 48 CS 7 to dscp 56 2011/6/27 Mike > Hi all I’m tryi

[OSL | CCIE_Voice] FRF.12 question

I believe this is correct If you do not use FRTS then you will be ok by doing nothing on the other interface I do not believe show traffic will show you anything as FRTS is not enabled You will need to use show policy-map interface ___ For more

Re: [OSL | CCIE_Voice] VMware ESXi for CCM servers

Make sure you're installing on an intel CPU. Had major issues installing to an AMD. I needed to install on an Intel pc (running server) the. 'export' to the AMD box. Once migrated it runs fine. On Saturday, March 21, 2009, Arun Kumar wrote: > Hi > > I'm running CUCM 7 and Unity Connection 7 on

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

Only use NTP Master in the following two cases: The router is not synchronized with an NTP server, but needs to act like oneThe router is synchronized with an NTP server, but you are told to have it act as a different stratum By default, an IOS device configured to sync with an NTP server will a

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

When you issue NTP Master it does add an association for the local router and if that stratum is lower than your external stratum, then your router will use the internal clock. You have to ensure your internal stratum is higher than the external you are using, ie: ntp master 15. There may be anot

Re: [OSL | CCIE_Voice] ip pim dense mode

hi, for UCM moh, i understand u need. however in bracnch, without the command "ip pim dense mode" , router allready been fool to get from its flash :) On Mon, Jun 27, 2011 at 3:53 AM, Rogers Ochieng, CCIE #28970 < rogersochi...@gmail.com> wrote: > You actualy don't need pim dense mode when ro

Re: [OSL | CCIE_Voice] Study lab equipment question

Yes, or another cucm server with a vwic on hq router. Pstn/wan could be anything since its not tested. duy ccie #27737 voice tmobile g2 On Jun 27, 2011 2:08 PM, "Bill Lake" wrote: > Could you use a 3725 for your PSTN? > > On Mon, Jun 27, 2011 at 12:03 PM, ccieid1ot wrote: >> If not 2811 then a

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

But i have studied that NTP master on the HQ router will force the HQ RTR to loose its NTP sync with external source 10.10.100.2 and will start making its internal clock as the master.. This can be seen in the sh NTP associations. Please suggest what should be done -Original Message- F

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

Believe you also need "ntp master" command. Chris On Mon, Jun 27, 2011 at 11:56 AM, wrote: > Hello All, > > > When asked to configure NTP server for CUE as the HQ Router's loopback IP > or HQ routers Voice Vlan IP, > should i configure NTP master command on the HQ router besides below > config

Re: [OSL | CCIE_Voice] Study lab equipment question

Could you use a 3725 for your PSTN? On Mon, Jun 27, 2011 at 12:03 PM, ccieid1ot wrote: > If not 2811 then at least a 2801 should suffice.  The 3725 won't support > 'cme 7.0' > > duy > ccie #27737 voice > > tmobile g2 > > On Jun 27, 2011 10:27 AM, "Scott Jones" wrote: >> Hi everyone-I've got a qu

Re: [OSL | CCIE_Voice] Study lab equipment question

3725 won't do cme 7.0. This means you will miss ALOT of features on CME that are tested (the one that stands out in my head is octo-line). You could get by with a 3725 as a PSTN and Frame-Relay switch, but that's about it. On Mon, Jun 27, 2011 at 9:46 AM, Scott Jones wrote: > Hi everyone—I’v

[OSL | CCIE_Voice] MLS QoS issue

Hi all I'm trying to lab up a QOS run through and for some reason the switch is resetting everything to 0 Switch config: mls qos map cos-dscp 0 8 16 24 32 46 48 56 mls qos interface FastEthernet0/3 switchport mode access switchport voice vlan 10 mls qos trust dscp spanning-tree por

Re: [OSL | CCIE_Voice] Study lab equipment question

If not 2811 then at least a 2801 should suffice. The 3725 won't support 'cme 7.0' duy ccie #27737 voice tmobile g2 On Jun 27, 2011 10:27 AM, "Scott Jones" wrote: > Hi everyone-I've got a question regarding lab equipment for my home lab...I know on the test it uses 2811s, but it's hard to drop t

Re: [OSL | CCIE_Voice] CUE NTP synchronisation with HQ Router Loopback 0

Hello All, When asked to configure NTP server for CUE as the HQ Router's loopback IP or HQ routers Voice Vlan IP, should i configure NTP master command on the HQ router besides below configuration? HQ Router: ntp server 10.10.100.2___ For more i

Re: [OSL | CCIE_Voice] Study lab equipment question

You can use 2801 for PSTN, HQ and BR1 in the IPX structure, it means you have to do some changes as the layout is somewhat different. You would need one 2811 or 2821 to use the CUE network module or AIM-CUE. On Mon, Jun 27, 2011 at 8:46 AM, Scott Jones wrote: > Hi everyone—I’ve got a question r

Re: [OSL | CCIE_Voice] Urgent priority check

i would only use UP when there is an overlap in dial plan to avoide inter digit timeout - for nanp this should only be for 9911 which overlaps with local 9[2-9]XX For 911 we shouldln't need it. cheers On Mon, Jun 27, 2011 at 6:26 AM, Ki Wi wrote: > Yes,the only thing you will need urge

Re: [OSL | CCIE_Voice] Test Email

email: It's amazing! On Mon, Jun 27, 2011 at 6:52 AM, Second CCIE wrote: > Test email > ___ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out

Re: [OSL | CCIE_Voice] FRF.12 question

Alex, definitely needed. Test it out by enabling it on HQ router than don't enable on BR2 router. Now open up the cue gui and see if it operated correctly. duy ccie #27737 voice tmobile g2 On Jun 27, 2011 6:17 AM, "Alex Goh" wrote: > Hi Shrini, > > I guess what cristobal trying to mean is when

[OSL | CCIE_Voice] Study lab equipment question

Hi everyone-I've got a question regarding lab equipment for my home lab...I know on the test it uses 2811s, but it's hard to drop that kind of coin (even on ebay, they're still running close to $7-800...). I was thinking about getting 3725s as they're cheaper, but not sure if that will screw me

[OSL | CCIE_Voice] Test Email

Test email ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com

Re: [OSL | CCIE_Voice] ip pim dense mode

You actualy don't need pim dense mode when route in below command *multicast moh** multicast-address* *port* *port* [*route* *ip-address-list*] route ip-address-list—(Optional) Declares the IP address or addresses from which the flash MOH packets can be transmitted. Rogers On 27 June 2011 10:3

Re: [OSL | CCIE_Voice] how to retrieve list of Active IP Phones ONLY...

Alex, We have 3 servers in Cluster. One of them is Dead. Rest 2 Servers running RIS Data Collertor service.. Regards Rashid. From: Alex Goh To: Rashid Khan Cc: Julien Krieger ; ccie voice Sent: Mon, June 27, 2011 2:23:11 PM Subject: Re: [OSL | CCIE_Voice] h

Re: [OSL | CCIE_Voice] how to retrieve list of Active IP Phones ONLY...

Hi Rashid, Looks like there is some issue with the RIS Data Collertor service as per the screen capture. Can you confirm that service is running on all the servers? Regards, Alex On Mon, Jun 27, 2011 at 3:23 PM, Rashid Khan wrote: > Thanks Julien, that resolved my problem but partially not fu

Re: [OSL | CCIE_Voice] remote dest profile

it should show 5001 On Mon, Jun 27, 2011 at 1:38 PM, donny f wrote: > hi, > > > when we config Remote Dest Profile for SNR. > > When call come from our PSTN (6171234) phone to UCM ext phone , should > it show our ext 5001 or showing the SNR (PSTN #) ? > > for ie :we have S

Re: [OSL | CCIE_Voice] FRF.12 question

Hi Shrini, I guess what cristobal trying to mean is when he is using class based shaping, instead of FRTS which required the command on physical interface, do he need to care about the qos setting between HQ and BR1. By the way, I have one question though, for the case when FRTS was enable on HQ

Re: [OSL | CCIE_Voice] IPPM getting invalid device

oso check if you have already assign the user capability under licensing capability On Mon, Jun 27, 2011 at 4:47 AM, Cristobal Priego wrote: > does yourapp user matches the user in CUPS ? is ip phone messenger on in > CUPS? > do you have the CTI enabled and the CTI controll all devices group >

Re: [OSL | CCIE_Voice] FRF.12 question

It looks like not effected but it is. The bandwidth drops to 56k. Good idea is to apply the Br2 service policy to Br1 connected srl interface even you not shaping the traffic. sh frame-relay pvc will provide you the details. Thanks Shrini On 6/26/2011 2:34 PM, Cristobal Priego wrote: hello

Re: [OSL | CCIE_Voice] CME: + display for POTS dial-peer calls

Hi Adil, Phones at H323 gateway does not display + of calling number. -Shrini On 6/26/2011 6:19 PM, Adil Shaikh wrote: Hi Guys, run into a know issue of displaying + on H323/CME phone. the call is coming on POTS dial-peer on CME phone. Telco is sending + in the ANI but phone is not displaying

Re: [OSL | CCIE_Voice] ip pim dense mode

Hi Danny, You are configuring CUCM to multicast MOH and fooling the router by multicasting MOH locally on the same IP / port. (Trick behind MOH from flash) For the interfaces to forward multicast request you need "ip pim dense mode" command, specifically on voice vlan interface, else phones

Re: [OSL | CCIE_Voice] Challenges with Hardware VPN

Hi pithog, I faced the same problems in my first session and to overcome these problems, I stopped using DHCP and configured the IP address, subnet Mask, Gateway, and TFTP manually on all the IP phones. To stop the phones from changing their firmware, go to CUCM Admin page, then select Device

[OSL | CCIE_Voice] remote dest profile

hi, when we config Remote Dest Profile for SNR. When call come from our PSTN (6171234) phone to UCM ext phone , should it show our ext 5001 or showing the SNR (PSTN #) ? for ie :we have SNR6171234and match to 5001. ___

[OSL | CCIE_Voice] ip pim dense mode

hi all, for MOH from router flash, why we ever need this command " ip pim dense mode" on router and swith interface. Because we did not pass any multicast traffic, so why bother to put this command ? ___ For more information regarding industry leading

[OSL | CCIE_Voice] several doubt on routing

hi all, - if question did not mention "calling display in our own phone ", do we need to care in lab exam ? example : TO6175005 or TO96175005 - for TEHO call,do we use RP : 91408.! or 91408[2-9]xxx ? - when we use 9.011!#, Display in our phone

Re: [OSL | CCIE_Voice] Urgent priority check

Yes,the only thing you will need urgent priority will be something like 999 in a dialplan 9xxx. For general knowledge, this is required for singapore/ hk dial plan. Sent from my iPhone Pls pardon my fat fingers. On Jun 27, 2011, at 6:57 AM, Roger Carpio wrote: > I agree with Randall, if

Re: [OSL | CCIE_Voice] Urgent priority check

so , Urgent priorty is use for : 911 , 9.911 , and 9011.! and \+.! ,right ? is there any other case we need it ? On Sun, Jun 26, 2011 at 1:58 PM, Randall Saborio wrote: > I disagree, it is not needed for pattern ending in #. > > Usually it is for patterns starting in \+ AND ending in ! a