Hi All,
Below is the config from my lab HQ router
!
nterface Serial0/3/0
no ip address
encapsulation frame-relay
clock rate 64000
frame-relay intf-type dce
interface Serial0/3/0.1 point-to-point
bandwidth 768
ip address 10.10.111.1 255.255.255.0
ip pim sparse-dense-mode
frame-relay
From: Raees Shaikh racerra...@yahoo.com
To: CCIE Study ccie_voice@onlinestudylist.com
Sent: Sunday, November 20, 2011 5:15 PM
Subject: auto qos command does not show up
Hi All,
Below is the config from my lab HQ router
!
nterface Serial0/3/0
no ip address
encapsulation frame-relay
clock
added it under
frame-relay interface-dlci 202
let me know if it is OK?
From: Raees Shaikh racerra...@yahoo.com
To: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com
Sent: Sunday, November 20, 2011 9:18 AM
Subject: [OSL | CCIE_Voice] auto
You need to go under frame-relay interface-dlci xxx and configure the
command over there.
On Sun, Nov 20, 2011 at 3:45 PM, Raees Shaikh racerra...@yahoo.com wrote:
Hi All,
Below is the config from my lab HQ router
!
nterface Serial0/3/0
no ip address
encapsulation frame-relay
clock
Auto QoS goes under the DLCI. So it goes.
interface Serial0/3/0.1 point-to-point
bandwidth ### (You've done this already, but I'm pointing it out because it
can be really anoying to fix if forgotten)
frame-relay interface-dlci 201
auto qos voip (options)
On Sun, Nov 20, 2011 at 6:45 AM,
Hi Voiper,
From the traces its very clear that your route-list isn't registered and
that's why your calls aren't successful. Its showing that route-group isn't
available and not associated with route-list. This needs to be fixed.
Also, noticed that your h323 configuration is missing
SOFTWARE (fc2)
TR
-- next part --
An HTML attachment was scrubbed...
URL: /archives/ccie_voice/attachments/2020/8bf04f28/attachment.html
--
___
CCIE_Voice mailing list
CCIE_Voice
Very Important
Assuming that both sources and destination endpoints are having different
MRGLs assigned, the allocation is as follow:
1. For XCODE, TRP, and MTP, the MRGL of destination endpoint is used.
2. For CFB, the MRGL of CFB initiator is used.
3. For MoH, the MRGL of
Yes its supported and should be working. Confirm that same DN is present on
both phones and located in same partition.
Regards,
Mohammed Al Baqari
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of datucha123
datucha123
Sent:
Hi Guys,
It was my 5th attempt and i got lab 6 frustration is on peak everytime i went
for the lab i get new lab i dont know why
From last 2 months all my JR guys passed in dubai bec they got lab 3 and lab 4
in Dubai since last 2 months i saw lot of guys cleared from dubai
Now lab 6 i am so
Great information, thank you so much.
Can you please tell me, where that info resides? In SRND or CUCM System
Guide?
I have also another question:
For XCODE, TRP, and MTP, the MRGL of destination endpoint is used -
When I make an Outbound Call from the BR1 Phones through the ICT Trunk,
then
Hi Guys,
It was my 5th attempt and i got lab 6 frustration is on peak everytime i went
for the lab i get new lab
From last 2 months all my JR guys passed in dubai bec they got lab 3 and lab 4
in Dubai since last 2 months i saw lot of guys cleared from dubai
Now lab 6 i am so so so
hello, everyone.
I have several questions about the QoS:
1) As I know, the Frame Relay Fragment Size must be always calculated based
on the Interfaces Access Rate? Am I right? And when using the Auto QoS on
Frame Relay Subinteface, it will calculate the Framgent Size based on the
bandwidth
Is the setting set to mandatory under location in CUCM?
Randall
From: datucha123 datucha123 datucha...@gmail.com
To: ccie_voice@onlinestudylist.com
Sent: Sunday, November 20, 2011 8:29 AM
Subject: [OSL | CCIE_Voice] QoS for Frame Relay
hello, everyone.
Yes, Sure,
Mandatory (Video Desired)
But still no success :(
On Sun, Nov 20, 2011 at 9:58 PM, Randall Crumm rrcr...@yahoo.com wrote:
Is the setting set to mandatory under location in CUCM?
Randall
--
*From:* datucha123 datucha123 datucha...@gmail.com
*To:*
Do you have the locations in your Device pool and the proper device pool
assigned to the GW?
RC
From: datucha123 datucha123 datucha...@gmail.com
To: Randall Crumm rrcr...@yahoo.com
Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com
Sent:
Yes, the DPs are assigned correctly.
calls are successfully completed, but the RSVP is not rejecting the number
of calls when they exceed the configured max value.
On Sun, Nov 20, 2011 at 10:10 PM, Randall Crumm rrcr...@yahoo.com wrote:
Do you have the locations in your Device pool and the
Do you mean under the DHCP configuration, that such question has been on
the exam?
What do you mean under the SIP early offer? or MGCP TS?
On Sun, Nov 20, 2011 at 8:24 PM, Peter Jeff peterjeff2...@yahoo.com wrote:
Hi Guys,
It was my 5th attempt and i got lab 6 frustration is on peak
Put you whole configs Online here and we can take a look.
Randall
Sent from my iPhone
On Nov 20, 2011, at 10:20 AM, datucha123 datucha123 datucha...@gmail.com
wrote:
Yes, the DPs are assigned correctly.
calls are successfully completed, but the RSVP is not rejecting the number of
calls
are your MTPs registered and configured as rsvp under dspfarm profile?
if so can you send over your full ios configs
On Sun, Nov 20, 2011 at 6:20 PM, datucha123 datucha123 datucha...@gmail.com
wrote:
Yes, the DPs are assigned correctly.
calls are successfully completed, but the RSVP is not
after reading the root cause crappy wan
I set suspect the 2 meg wan is dsl which typically have lower upload speed.
a simple dsl speed test will give you this result.
you wan could be as as 128K end to end (2meg down - 128K up) = 128K end to
end not 2 meg . be sure to use the lower of upload and
Hello Experts,
I finally got all my phones together for my studies (3x7965, 1x7970,
3x7975). I am wondering now if I can actually export the configs of CUCM
after I register my phones so I don't have to be adding them every single
time I start a lab...
Any ideas?
*Emanuel Damasceno*
Hi - if using vmware you can take a snapshot (fastest and most flexible),
if bare metal you can use DRS to backup and restore full ucm configs, or
you can export phones to bat csv format and reimport them.
hth
On Sun, Nov 20, 2011 at 7:51 PM, Emanuel Damasceno aedamasc...@gmail.comwrote:
Hi Emanuel,
Yes, if i understand your question correctly you're talking about taking a
DRF backup of the cluster for CUCM and then perform a restore everytime you
start a Lab? Correct me if i'm wrong.
Well, my suggestion would be not to do that since actual lab does not give
you the Devices
Yes you can do that from bulk administration.
First you need to export the configuration (you can select what to export)
into a tar file then you download it to your local machine.
Then you import that tar file to CUCM back to resume.
In between you open the tar file and edit the CSV
This is an automated reply to your message CCIE_Voice Digest, Vol 69, Issue
114 sent to stewart.mcfarl...@provista-uk.com.
Dear ccie_voice-requ...@onlinestudylist.com
Thank you for your email.
Please note that due to unforseen circumstances I will be out of the office for
the rest of this
Well, the DHCP issue can be done easy if you look 5 minutes on
cisco.comdocumentation, by Early offer what you mean? no interdigit
timeout?
On Sun, Nov 20, 2011 at 2:22 PM, datucha123 datucha123 datucha...@gmail.com
wrote:
Do you mean under the DHCP configuration, that such question has been
I use Bulk Administration to import my phone configuration. Much easier than
putting them in manually. Just create a BAT Template for each phone type and
then create a CSV using BAT.XLT file you can download from CUCM.
___
For more information
Hi all,
Could you please help me to solve this:
There is 384 frame-rely PVC between HQ and BR1.
Enable FRF.12 on this
circuit , 10 ms as sampling rate.
16k for signaling traffic and 4 g.729 calls.
Assume all RTP traffic is marked with EF and signaling with CS3
Header Compression should be
SIP Early offer it is IOS command, it is equal to the configuration of fast
start on CUCM
http://www.cisco.com/en/US/docs/ios/voice/cube/configuration/guide/vb-gw-sipsip.html#wp1351645
It can be configured globally
SUMMARY STEPS
* 1. **enable*
* 2. **configure terminal*
* 3. **voice service
30 matches
Mail list logo
