[OSL | CCIE_Voice] MVA partial match issue

hi, I config the Service parameter for MVA , using "partial match" 7 digit . However when I dial the RD using 7 digit ,it never works. seem like UCM only take "Full match". I heard this is bug, Any suggestion for the work around if still want to use "partial match" ? d On Sun, Mar 17, 2013 at

Re: [OSL | CCIE_Voice] hugo.barr...@nexusis.com

Greetings Hugo, What it really comes down too. What is the question and what are results you're being asked to provide? Without knowing what the results are it is difficult to answer accurately appropriately. Michael Sears CCIE (V) 38404 Message: 1 Date: Sun, 24 Mar 2013 16:01:11 + From

Re: [OSL | CCIE_Voice] CCIE_Voice Digest, Vol 85, Issue 89

Hi Ivan This is phone firmware bug, i also have the same issue for my SB, when i put it in fallback mode it goes in fall back mode but wont show DN, work around is you have to move back to older version of phone firmware You have to downlaod this version of phone firmware SCCP41.8-5-4S.loads Re

Re: [OSL | CCIE_Voice] Outgoing Calls via T1 failed

Hi, Changing the selection to top down solve the issue :) thanks On Sat, Mar 23, 2013 at 2:27 AM, ikizoo4 kwon wrote: > use Topdwon for channel selection order in GW > > -- > Date: Sat, 23 Mar 2013 00:52:10 +0300 > From: aboaz...@gmail.com > To: ccie_voice@onlinestu

Re: [OSL | CCIE_Voice] CME-SRST

Hi, thanks for your help yes I have the type on the ephone, the way that I found to fix the problem is copyin the configuraton on notepad, removing the telephony-service and putting back again the configuration in the router, the line appears again on the phone and the ephone template takes effect

Re: [OSL | CCIE_Voice] CME-SRST

Bug you do not want to reset phones in SRST mode. It is for this reason that it would be recommended to test your SRST early in the lab , write mem, reload and not do SRST again. CME as SRST was new in these releases and is known to be very buggy. On Sunday, March 24, 2013, Ivan Darío Sánchez Cal

Re: [OSL | CCIE_Voice] CME-SRST

Have you got a type Ephone 1 Mac address .. Type 7965 Leslie Meade .. Mobile:778.228.4339 | Main: 604.676.5239 Email: leslie.me...@lvs1.com From: ccie_voice-boun...@onlinestudylist.com [m

[OSL | CCIE_Voice] CME-SRST

Hi, When I configure CME-SRST and I apply an ephone-template to a phone, I reset the phone and when the pone comes back there is no line on the phone, I check the configuration and everithing is fine , the button is associated with the phone, this is a bug? someone knows what is the workaround? T

Re: [OSL | CCIE_Voice] CME Presence

Gotcha, makes sense now. Thanks Bill. Regards, Hugo From: William Bell [mailto:b...@ucguerrilla.com] Sent: Sunday, March 24, 2013 11:18 AM To: Barrera, Hugo Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] CME Presence There is also a third method. The method you use will dep

Re: [OSL | CCIE_Voice] Phone Directory

Hello everyone can i add this additional command with no arm to the interface ?"mls qos trust dscp" interface GigabitEthernet0/1 queue-set 1 srr-queue bandwidth share 1 70 25 5 srr-queue bandwidth shape 3 0 0 0 priority-queue out mls qos trust dscp ===> this command Ben

Re: [OSL | CCIE_Voice] A simple uccx script for the requirement

Hi Vir, U can use default queue script and edit it with minor changes if required. When agents are not loged-in you will hear =all are agents are currently busy... after agents login, you can play recorded prompts regards, Vikky On Sat, Mar 23, 2013 at 8:38 PM, virajith wrote: > HI All,

Re: [OSL | CCIE_Voice] CME Presence

There is also a third method. The method you use will depend on the requirements in the lab. They may or may not make a direct statement. More than likely they will give requirements which "hint" at the correct approach. Methods button 2m1 (button 2 monitors ephone-dn 1) Monitors a single D

[OSL | CCIE_Voice] cRTP 2-4 bytes

Hi All, It seems that most calculations I see use 2 bytes when header compression is turned on. On Occasion I also seem 4 bytes used. If I understand correctly, 4 bytes should be used if udp checksum is enabled. My questions is: What enables/disables udp checksum? Is it safe to always use 2 bytes

Re: [OSL | CCIE_Voice] CME Presence

It will be stated in the lab which way… but if they do not it is up to you Leslie Meade From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Barrera, Hugo Sent: Sunday, March 24, 2013 9:01 AM To: ccie_voice@onlinestudylist.com Subject: [OSL

[OSL | CCIE_Voice] CME Presence

Hi Guy’s, Question for the seasoned test takers or CCIE’s…regarding CME Presence there appears to be two ways to get the same thing done, shown below. If required to monitor the status of another phone which way would you do it? Way 1: ephone-dn 1 number 1001 description 4001 allow watch ! !