Looking for BAD / Faulty core memory for a display piece
Unrepairable preferred It'll be going into an epoxy resin setup that someone I know is doing for a table, and I really want to get something that still LOOKS OK but is... well, just faulty and won't be restorable to service so we don't destroy any potentially usable hardware. Ideas/suggestions welcome! -- Gary G. Sparkes Jr. KB3HAG
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
Mistake below, Vo should be a fraction of 5 volts, not "a volt" when operating On Fri, Jul 10, 2020 at 2:28 PM Ian Finder wrote: > A few responses- > > On Fri, Jul 10, 2020 at 12:29 PM Brent Hilpert wrote: > >> Reading that datasheet, it appears that to reduce power consumption those >> sensors employ pulsed sleep/wake operation, presenting up to a 1/8 second >> delay in response time. Probably not very good for use in a keyboard, and >> something to watch out for if looking for a modern replacement sensor. >> > > Great catch, Brent. I'll keep looking at other options. I must have > skimmed the data sheet a bit too hard. > > On Fri, Jul 10, 2020 at 01:19 PM Santo Nucifora wrote: > > I can't help as I have a full keyboard that I'd like to keep intact but > this is a home made... > > I have many of the keyboards with these 3-pin switches. As mentioned > previously, what the sensors need to be electrically is the ***A sensor, > which is harder to find by a considerable margin. Sink level, vs sink > pulse, vs scan. In Al's words- non-multiplexed contact closure type. > > http://telcontar.net/KBK/Micro_Switch/SD > > The machine is a Xerox system. > > On Fri, Jul 10, 2020 at 02:01 PM Al Kossow wrote: > > It would be interesting to understand the failure mode. > > I wonder if they passivated the die correctly > > I agree. What is interesting to me is this- If I look at other hall effect > keyboards, and even other examples of the same sensor: > http://telcontar.net/KBK/Micro_Switch/images/SD/Micro_Switch_SD_Hall_sensors.jpg > > They appear to be encased in a hard, black epoxy of some kind. Some of the > other keyboards I have with the same SD switches- but alas the wrong sensor > output type- appear to exhibit this as well, and have not failed. > > My failed sensors have something with the gelatinous consistency and > transparency of RTV silicone. It did not appear to have become conductive, > but who knows. There were three distinct failure modes: > > * 1) Output stuck at Vcc (+5v) - By the spec sheet, this should never > happen. Vo should be a fraction of a volt when not actuated, dropping to 0v > when actuated. > > * 2) Output stuck at 0v - Self explanatory. > > * 3) Output appears to be correct-ish Vo, but does not actuate to 0v with > magnet. This was the rarest failure. > > Based on this, my best guess is that there are two failure modes: > > 1) RTV silicone decomposes over time, leaching something into the die that > destroys the IC's passivization layer per Al's comment > > 2) The RTV silicone (or similar) is not robust enough to shield the > delicate sensor die to ceramic substrate connections from vibration and > force-based trauma as it decomposes. > > My expectation is that most of these switches have the black epoxy style > of package for a reason- this is the correct design, hopefully should last > a long time, and the ones that use this transparent goop will all > inevitably die. > > I have never seen any other semiconductor die encased in what appears to > be silicone... > > This is, incidentally, more about keyboards than I have ever cared to > know. The fact that this is an entire hobby for some people is all the more > shocking to me. I'd far rather be debugging some logic... > > > Cheers- I > > > > > >
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
On 7/10/20 2:14 PM, Al Kossow via cctalk wrote: There are a couple of serious researchers out there who do useful work, here is what exists for the SD switch https://deskthority.net/wiki/Micro_Switch_SD_Series the schematic of the 1660 microswitch keyboard can be found on page 235 of the maint manual http://bitsavers.org/pdf/diablo/printer/400083-01_1660_Maintenance_Jul78.pdf it uses x/y matrix style hall modules the drawing you pointed to uses pulsed output switches neither type will work in his application
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
A few responses- On Fri, Jul 10, 2020 at 12:29 PM Brent Hilpert wrote: > Reading that datasheet, it appears that to reduce power consumption those > sensors employ pulsed sleep/wake operation, presenting up to a 1/8 second > delay in response time. Probably not very good for use in a keyboard, and > something to watch out for if looking for a modern replacement sensor. > Great catch, Brent. I'll keep looking at other options. I must have skimmed the data sheet a bit too hard. On Fri, Jul 10, 2020 at 01:19 PM Santo Nucifora wrote: > I can't help as I have a full keyboard that I'd like to keep intact but this is a home made... I have many of the keyboards with these 3-pin switches. As mentioned previously, what the sensors need to be electrically is the ***A sensor, which is harder to find by a considerable margin. Sink level, vs sink pulse, vs scan. In Al's words- non-multiplexed contact closure type. http://telcontar.net/KBK/Micro_Switch/SD The machine is a Xerox system. On Fri, Jul 10, 2020 at 02:01 PM Al Kossow wrote: > It would be interesting to understand the failure mode. > I wonder if they passivated the die correctly I agree. What is interesting to me is this- If I look at other hall effect keyboards, and even other examples of the same sensor: http://telcontar.net/KBK/Micro_Switch/images/SD/Micro_Switch_SD_Hall_sensors.jpg They appear to be encased in a hard, black epoxy of some kind. Some of the other keyboards I have with the same SD switches- but alas the wrong sensor output type- appear to exhibit this as well, and have not failed. My failed sensors have something with the gelatinous consistency and transparency of RTV silicone. It did not appear to have become conductive, but who knows. There were three distinct failure modes: * 1) Output stuck at Vcc (+5v) - By the spec sheet, this should never happen. Vo should be a fraction of a volt when not actuated, dropping to 0v when actuated. * 2) Output stuck at 0v - Self explanatory. * 3) Output appears to be correct-ish Vo, but does not actuate to 0v with magnet. This was the rarest failure. Based on this, my best guess is that there are two failure modes: 1) RTV silicone decomposes over time, leaching something into the die that destroys the IC's passivization layer per Al's comment 2) The RTV silicone (or similar) is not robust enough to shield the delicate sensor die to ceramic substrate connections from vibration and force-based trauma as it decomposes. My expectation is that most of these switches have the black epoxy style of package for a reason- this is the correct design, hopefully should last a long time, and the ones that use this transparent goop will all inevitably die. I have never seen any other semiconductor die encased in what appears to be silicone... This is, incidentally, more about keyboards than I have ever cared to know. The fact that this is an entire hobby for some people is all the more shocking to me. I'd far rather be debugging some logic... Cheers- I
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
What type of computer is your friend restoring? I don't think he wants to reveal that, and it shouldn't matter anyway. There are a couple of serious researchers out there who do useful work, here is what exists for the SD switch https://deskthority.net/wiki/Micro_Switch_SD_Series
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
Hi Ian, What type of computer is your friend restoring? I can't help as I have a full keyboard that I'd like to keep intact but this is a home made terminal/keyboard made from Diablo 1620 parts including the keyboard and I believe the HyTerm main board. It has SD switches but they are mostly 4B3Bs. These are said to be the same hall effect switches as at least one of the famous Symbolic keyboards so that's likely a dead end. I do have the schematic for this board if it's helpful. Homemade keyboard pics: http://vintagecomputer.ca/vintage-homemade-keyboard/ Schematic: http://vintagecomputer.ca/files/Diablo/Diablo%20HyTERM%20HPR01%20Schematic.pdf On Fri, Jul 10, 2020 at 1:26 AM Ian Finder via cctalk wrote: > I know what you guys are thinking- no, this isn't for a keyboard collection > or some modern build or some other nonsense like that. > > I have a friend who is restoring a fairly interesting and historically > significant vintage computer- a and subject to what appears to be a > batch-related encapsulation failure on the proprietry hall effect sensors, > but could have been some other trauma, around a little over half of them > are bad. > > The correct SD-series replacement switch would be the 4B3A- > > *** These can allegedly be found on some of the Diablo printing > terminals.** > > It is possible other switches ending in ***A could be made to work with a > bit of labor and disassembly (swapping the fairly brittle sensors). > > I am not a keyboard expert but I have learned that you can remove a key on > some of these microswitch keyboards and read the model fairly easily. > > Please let me know if you have a lead on a donor for these switches. They > will be put to good use, and you can reply to me off list for more details. > > Thanks, > > - I >
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
On 2020-Jul-10, at 11:27 AM, Ian Finder via cctalk wrote: > On Fri, Jul 10, 2020 at 11:06 AM Al Kossow via cctalk > wrote: >> >> Since it isn't very fancy, I wonder if you could make a new board with a >> modern Hall >> effect sensor? You just need a contact closure. > Yeah Al, that's a great suggestion. I was looking at the AH1815 last night. > The challenge is getting the whole assembly as thin as the original, which > presents a not insignificant challenge- > > Even using the SOT553 package of this: > https://cdn.sparkfun.com/assets/4/4/8/2/a/AH1815.pdf - I'd have to do some > trickery, like have it mount into a hole into the center of the board. Reading that datasheet, it appears that to reduce power consumption those sensors employ pulsed sleep/wake operation, presenting up to a 1/8 second delay in response time. Probably not very good for use in a keyboard, and something to watch out for if looking for a modern replacement sensor.
HP 16C Badge (logo)
This is not exactly vintage computer, but it is very close. A friend just gave me an HP 16C calculator in excellent, working condition, EXCEPT the 16C badge (or logo if you prefer) is missing. I seem to recall that, some years ago, someone on this list knew of a source for replacements but I can't find it in the archive. So, I'll ask, does anyone know where to get a replacement 16C badge? Thanks, Bill S. -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
On 7/10/20 10:42 AM, Electronics Plus via cctech wrote: I have a number of keyboards with Micro Switch ST switches, but no SD. Does anyone still use old Memorex or Telex keyboards? YES! I have terminals w/o keyboards
VCF Midwest Cancellation
We regret to announce... There will be no VCF Midwest this year. The conditions imposed upon us by the CoViD-19 pandemic and related government regulations, as well as a depressed expected turn-out figure, will make it impossible for us to host an event of the size and quality our dedicated fans have come to expect. Thus today we have terminated our 2020 contract with Waterford Banquets and the Clarion Inn hotel. We recommend cancelling your hotel and travel reservations, if you have made them, and we hope that you have not been too greatly inconvenienced by our change of plans. We also wish to express our thanks for the many responses we received to our survey sent back in May. Your feedback was informative, interesting, humorous and most of all, essential in helping us make the right decision about this year's show. The good news is that we have an excellent relationship with our host venue and have already locked in our contract for 2021. Although a long way off, plans will take shape early next year for that show, so please keep an eye out for further announcements of VCFMW 16 (or will it be 15b? We don't know yet!) Also, following the lead of other cancelled festivals, we are considering a Virtual VCFMW to be held on one or more of the dates allocated for this year's show (Sept 12 or 13, 2020). If we think we can pull off something half as entertaining as the real thing, maybe we'll do it. Watch your email for announcements sometime in August. Your humble(d) organizer - - jason If you would like to repost this message in your own forums, feel free to do so by using this link: https://us18.campaign-archive.com/?u=6d177060bd4511e27d05266a5=02ddfacc10
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
Yeah Al, that's a great suggestion. I was looking at the AH1815 last night. The challenge is getting the whole assembly as thin as the original, which presents a not insignificant challenge- Even using the SOT553 package of this: https://cdn.sparkfun.com/assets/4/4/8/2/a/AH1815.pdf - I'd have to do some trickery, like have it mount into a hole into the center of the board. On Fri, Jul 10, 2020 at 11:06 AM Al Kossow via cctalk wrote: > On 7/10/20 9:45 AM, Al Kossow via cctalk wrote: > > > 4B3A is a non-multiplexed contact closure type which is extremely > difficult to find. > > Since it isn't very fancy, I wonder if you could make a new board with a > modern Hall > effect sensor? You just need a contact closure. > >
Re: In search of 4B3A Microswitch Keyswitches (for a system restoration, not keyboarding)
On 2020-Jul-09, at 10:12 PM, Ian Finder wrote: >> On Jul 9, 2020, at 21:58, Brent Hilpert wrote: >> On 2020-Jul-09, at 9:39 PM, Ian Finder via cctalk wrote: >> >>> I know what you guys are thinking- no, this isn't for a keyboard collection >>> or some modern build or some other nonsense like that. >>> >>> I have a friend who is restoring a fairly interesting and historically >>> significant vintage computer- >>> The correct SD-series replacement switch would be the 4B3A- >>> >>> *** These can allegedly be found on some of the Diablo printing >>> terminals.*** >>> >>> Subject to what /appears/ to be a batch-related encapsulation failure in >>> the glue on the proprietary hall effect sensors, around a little over half >>> of the switches on the current keyboard are bad. >>> >>> It is possible other switches ending in ***A could be made to work with a >>> bit of labor and disassembly (swapping the fairly brittle sensors). >>> >>> I am not a keyboard expert but I have learned that you can remove a key on >>> some of these microswitch keyboards and read the model fairly easily on >>> each switch. >>> >>> Please let me know if you have a lead on a donor for these switches. They >>> will be put to good use, and you can reply to me off-list for more details. >> >> Are these the key-switch model which snap into a thin-gauge springy >> stainless-steel U-channel to form the rows of the keyboard? > No, as I understand it that is the predecessor OK, too bad, in my parts stash I have an orphan (caseless) made-by-Microswitch keyboard from 1975, using the key-switch type as I described. I had a couple of the key-switches open years ago. According to my notes there are two types of key-switch, one for characters (black plunger) and one for modifiers (shift,ctl) (green plunger), the chip IDs (inside the key-switches) are 42B and 40H respectively.
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
Thanks Cindy- Unfortunately those won't work :( On Fri, Jul 10, 2020 at 10:42 AM Electronics Plus wrote: > I have a number of keyboards with Micro Switch ST switches, but no SD. > Does anyone still use old Memorex or Telex keyboards? > > -Original Message- > From: cctech [mailto:cctech-boun...@classiccmp.org] On Behalf Of Ian > Finder via cctech > Sent: Thursday, July 09, 2020 11:34 PM > To: classic...@classiccmp.org > Subject: In search of 4B3A Microswitch Keyswitches (for a restoration, not > a keyboard collector!) > > I know what you guys are thinking- no, this isn't for a keyboard collection > or some modern build or some other nonsense like that. > > I have a friend who is restoring a fairly interesting and historically > significant vintage computer- a and subject to what appears to be a > batch-related encapsulation failure on the proprietry hall effect sensors, > but could have been some other trauma, around a little over half of them > are bad. > > The correct SD-series replacement switch would be the 4B3A- > > *** These can allegedly be found on some of the Diablo printing > terminals.** > > It is possible other switches ending in ***A could be made to work with a > bit of labor and disassembly (swapping the fairly brittle sensors). > > I am not a keyboard expert but I have learned that you can remove a key on > some of these microswitch keyboards and read the model fairly easily. > > Please let me know if you have a lead on a donor for these switches. They > will be put to good use, and you can reply to me off list for more details. > > Thanks, > > - I > > > -- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus > >
RE: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
I have a number of keyboards with Micro Switch ST switches, but no SD. Does anyone still use old Memorex or Telex keyboards? -Original Message- From: cctech [mailto:cctech-boun...@classiccmp.org] On Behalf Of Ian Finder via cctech Sent: Thursday, July 09, 2020 11:34 PM To: classic...@classiccmp.org Subject: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!) I know what you guys are thinking- no, this isn't for a keyboard collection or some modern build or some other nonsense like that. I have a friend who is restoring a fairly interesting and historically significant vintage computer- a and subject to what appears to be a batch-related encapsulation failure on the proprietry hall effect sensors, but could have been some other trauma, around a little over half of them are bad. The correct SD-series replacement switch would be the 4B3A- *** These can allegedly be found on some of the Diablo printing terminals.** It is possible other switches ending in ***A could be made to work with a bit of labor and disassembly (swapping the fairly brittle sensors). I am not a keyboard expert but I have learned that you can remove a key on some of these microswitch keyboards and read the model fairly easily. Please let me know if you have a lead on a donor for these switches. They will be put to good use, and you can reply to me off list for more details. Thanks, - I -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
On 7/10/20 9:45 AM, Al Kossow via cctalk wrote: 4B3A is a non-multiplexed contact closure type which is extremely difficult to find. Since it isn't very fancy, I wonder if you could make a new board with a modern Hall effect sensor? You just need a contact closure.
Re: In search of 4B3A Microswitch Keyswitches (for a restoration, not a keyboard collector!)
On 7/9/20 9:34 PM, Ian Finder via cctalk wrote: The correct SD-series replacement switch would be the 4B3A- It would be interesting to understand the failure mode. I wonder if they passivated the die correctly? 4B3A is a non-multiplexed contact closure type which is extremely difficult to find. The modules out of any xx3A switch should work. The first two are the part number of the switch body. The switch type is stamped into the left side of the switch module plastic so all you need to do is pop off the keytop to read it.
