Hi,
We use following method. I hope its helpful.
- By Phone #1:
Dial 0080001001 (international toll free number) tell operator to connect
to 8884432447 i-e Ext of Cisco TAC
- Requeue via the email :
- Send an e-mail to t...@cisco.com with in subject REQUEUE CASE id
- Call our Customer
It sounds like running those links as routed links then running OTV over the
top for layer 2 would be a better solution for you.
Just need to front up the cash for the license.
Andrew Jones
Alphawest
-Original Message-
From: cisco-nsp-boun...@puck.nether.net
Unfortunately there are good reasons to combine switching and routing.
Otherwise you are stuck with a router on a stick configuration.
I believe A9Ks where not meant to be an access layer devices (the ports are
way too expensive) so you'd have at least an access layer infrastructure
doing .1q,
That's exactly what we also did.
MPLS ACLs work fine with IRB on MX, so we switched to them.
Probably the new ASR9k RSP/LCs (will) support it, but they are way too
expensive to proceed with a replacement.
--
Tassos
Mack McBride wrote on 19/07/2012 22:45:
Unfortunately there are good reasons
I'd go with a DD-WRT image http://www.dd-wrt.com/ on
a good (meaning fast cpu and 64+ MB of flash mem)
home router. It will do far more than a typical
expensive small office router for a lot less, even
things you may not think you'll need now but might
later. I know you said no Linksys but the
Hi all
We have a ASR1K with
Cisco IOS Software, IOS-XE Software
(X86_64_LINUX_IOSD-ADVIPSERVICESK9-M), Version 15.2(2)S, RELEASE
SOFTWARE (fc1)
IOS XE Version: 03.06.00.S
ASR1000-ESP40
ASR1000-SIP40
Case that we have with the ISG , is very strange .
Here are the policy and acl for
Sorry , everywhere is
command 0 activate-service
not command 0 deactivate-service
just copy/paste error :)
On Fri, Jul 20, 2012 at 1:12 PM, Georgi Genov linuxloa...@gmail.com wrote:
Hi all
We have a ASR1K with
Cisco IOS Software, IOS-XE
Hi,
On Thu, Jul 19, 2012 at 02:58:58PM -0400, Jared Mauch wrote:
I think my point is.. If you are buying an asr9k
you can likely afford an ethernet switch vs using an
expensive router port.
Sometimes BVI are the poor man's multi-chassis etherchannel to
get redundant links to
On 20 July 2012 12:08, Gert Doering g...@greenie.muc.de wrote:
Sometimes BVI are the poor man's multi-chassis etherchannel to
get redundant links to downstream switches...
Yes indeed.
It is equally frustrating that neither HSRP nor VRRP are supported on
ASR1k/IOS-XE BDI interfaces.
Aled
I've been reasonably happy with the RB750(G|GL|). The configuration
language is not a Cisco knock-off, but you'll figure it out easily enough.
Sure I have a laundry list of bugs and complaints, but that's the case
for the big name guys as well, and it's easy to exceed expectations
when one is
Hi man , I have a question
I want to do a command one time at a specific time
I mean , for example
after 5 min i will add a route
after 10 min i will add another route and remove the older one and so
I have configured the below , but it keep running
PE1#sh run | sec event manager
event manager
11 matches
Mail list logo
