* Andras HORVATH wrote:
linux-image-2.6.18-4-alpha-smp still suffers from Could not
allocate X bytes percpu data when loading modules (for example,
xfs, eepro100 and e100).
I've found this discussion (regarding the previous version,
linux-image-2.6.18-3-alpha-smp):
Limiting the Dom0 number of cpus to 1 in
/etc/xend-confix.xsp (dom0-cpus 1)
cures the problem.
Additional I've pinned Domain-0 vcpu0 to cpu0
(xm vcpu-pin 0 0 0)
but this is not neccessary.
# xm vcpu-list
Name ID VCPUs CPU State Time(s) CPU Affinity
Domain-00 0
Dear Jurij,
thank you very much. modprobe works fine without an error. But I could
not access the interface. iwconfig does not show the capabilities of the
interface.
Best regards
Lars
On Sat, Feb 10, 2007 at 12:41:37PM +0100, lars kaleschke wrote:
*** Please type your report below
Package: kernel
Version: 2.6.18-3-486
Severity: normal
Tags: patch Etch
The driver for ati sb600 IDE controller has bug.
SB600 ide controller has only one channel. Here is the patch:
--- drivers/ide/pci/atiixp.c.orig 2007-02-15 13:12:43.0
+0800
+++ drivers/ide/pci/atiixp.c
Package: linux-image
Version: 2.6.18-3-486
I failed to install Etch (i386 NETINST Binary-1 20070211) on the ati
sb600 chipset platform if I set the SATA to legacy IDE mode in the
system bios.
It prompts:
ata3: sata link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: qc timeout (cmd 0xec)
Package: kernel
Version: 2.6.18-3-486
Severity: serious
Tags: patch Etch
The driver for ati sb600 IDE controller has bugs.
It doesn't set the PATA in proper DMA mode.
When use 40-pin cable for PATA disk, sometimes, bad CRC makes the system
fail to boot with kernel panic. The kernel will report:
Hello!
I just wanted to mention that the bug disussed here still exists on my
box using the kernel from
http://people.debian.org/~nobse/kernel/linux-2.6/i386/
(in my case linux-image-2.6.18-4-k7_2.6.18-9_i386.deb)
Here the output from dmesg:
[...]
Type: Direct-Access
Processing commands for [EMAIL PROTECTED]:
reassign 411016 linux-2.6
Bug#411016: can't install Etch on ati sb600 mother board when set sata to
legacy ide mode.
Warning: Unknown package 'linux-image'
Bug reassigned from package `linux-image' to `linux-2.6'.
--
Stopping processing here.
Please
Processing commands for [EMAIL PROTECTED]:
# Automatically generated email from bts, devscripts version 2.9.27
# hardware-specific bug
severity 411024 important
Bug#411024: ati sb600 pata udma mode will cause kernel panic
Severity set to `important' from `serious'
End of message, stopping
severity 410807 ciritcal
I still reckon 'being unable to do anything on the machine' as a critical bug.
Thanks.
Radek
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Dear kernel team,
not only because of an upcoming talk on the status of etch, but also
out of genuine interest and the desire to improve things, I am
rather interested in what's blocking etch right now. From what I've
heard, the major showstopper seems to be that we currently don't
have a
Processing commands for [EMAIL PROTECTED]:
# Automatically generated email from bts, devscripts version 2.9.27
owner 406055 [EMAIL PROTECTED]
Bug#406055: Regression: Can't HDIO_GETGEO on CCISS RAID devices
Bug#409075: lilo: major error on lvm root on cciss raid
Owner recorded as [EMAIL
On Thu, Feb 15, 2007 at 07:54:36PM +, martin f krafft wrote:
Dear kernel team,
not only because of an upcoming talk on the status of etch, but also
out of genuine interest and the desire to improve things, I am
rather interested in what's blocking etch right now. From what I've
heard,
Your message dated Thu, 15 Feb 2007 16:04:44 -0700
with message-id [EMAIL PROTECTED]
and subject line fixed
has caused the attached Bug report to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Your message dated Thu, 15 Feb 2007 16:04:44 -0700
with message-id [EMAIL PROTECTED]
and subject line fixed
has caused the attached Bug report to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Version: 2.6.18.dfsg.1-9
I could reproduce w/ 2.6.17-7 and 2.6.18-8 but not with
2.6.18.dfsg.1-10. I'm pretty sure that this was fixed by one of the
cciss backports i did in -9 (though I didn't test it explicitly), so
marking as closed in that version.
--
dann frazier
--
To UNSUBSCRIBE,
On Thu, Feb 15, 2007 at 02:29:31PM -0700, dann frazier wrote:
I'm actively working on #406055 - finally got a machine setup to
reproduce it on, and am narrowing down the breaking changeset.
Done, closed
--
dann frazier
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of
On Sunday 11 February 2007 07:54, Jurij Smakov wrote:
The config variable CONFIG_DEBUG_FS, enabled recently for all kernel
flavours adds over 400K to the size of the compressed image size on
sparc32. As a result, it does not boot anymore (uncompressed image
does not fit into the allotted
Your message dated Thu, 15 Feb 2007 17:54:24 -0700
with message-id [EMAIL PROTECTED]
and subject line no longer applicable since xen image is pae
has caused the attached Bug report to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is
Version: 2.6.18.dfsg.1-9
PAE is now enabled for the Xen flavour. As I understand it, this bug
is only believed to exist in non-PAE builds. I cannot reproduce w/
2.6.18.dfsg.1-10. Setting the fixed version as 2.6.18.dfsg.1-9, since
that is the first upload of the PAE-enabled version.
[EMAIL
On Thu, Feb 15, 2007 at 02:29:31PM -0700, dann frazier wrote:
As for #404927 - I think all of the information is there to provide a
patch to udev to workaround the issue, and I think Marco is planning
to do, but haven't heard back from him. In our last conversation he
said that a patch would
Processing commands for [EMAIL PROTECTED]:
# Automatically generated email from bts, devscripts version 2.9.27
reassign 411023 linux-2.6
Bug#411023: ati SB600 ide controller has only one channel
Bug reassigned from package `kernel' to `linux-2.6'.
End of message, stopping processing here.
Processing commands for [EMAIL PROTECTED]:
tags 411024 + pending
Bug#411024: ati sb600 pata udma mode will cause kernel panic
Tags were: etch patch
Tags added: pending
End of message, stopping processing here.
Please contact me if you need assistance.
Debian bug tracking system administrator
Processing commands for [EMAIL PROTECTED]:
tags 411023 + pending
Bug#411023: ati SB600 ide controller has only one channel
Tags were: etch patch
Tags added: pending
End of message, stopping processing here.
Please contact me if you need assistance.
Debian bug tracking system administrator
On Thu, Feb 15, 2007 at 05:59:50PM -0700, dann frazier wrote:
I sent a (broken) patch to Marco - he pointed out the flaw said he
plans to implement it differently. Once he does so, this bug should be
knocked down to non-RC.
I also closed #399113 - I couldn't reproduce it and, aiui, it only
Rakotomandimby (R12y) Mihamina
[EMAIL PROTECTED] writes:
Hi,
What is the difference between those two kernels?
Their description is the same and I dont know which one to take...
http://packages.debian.org/unstable/admin/linux-image-2.6.18-4-xen-amd64
Otavio Salvador [EMAIL PROTECTED] writes:
maximilian attems [EMAIL PROTECTED] writes:
On Thu, Feb 01, 2007 at 10:14:10AM +0100, Matthias Popp wrote:
Hallo,
Why is kernel 2.6.19 removed from here ?
http://kernel-archive.buildserver.net/debian-kernel/pool/main/l/linux-2.6/
just use the
dann frazier [EMAIL PROTECTED] writes:
On Fri, Feb 09, 2007 at 10:47:58PM -0800, Jurij Smakov wrote:
I believe the original idea was to create d-k-m for discussions and
keep d-k as the address in maintainer field (and the primary contact
address for the user requests). This appears to be
Thomas GOIRAND [EMAIL PROTECTED] writes:
Package: linux-image-2.6-xen-686
Severity: wishlist
Hello,
Our package, dtc-xen, uses /usr/lib/python/xen installed by the
normal xen source package using make install. With this package,
there is no such folder, but instead something with version
29 matches
Mail list logo
