Re: [PATCH v2 6/6] drm/panel: Add Ilitek ILI9341 DBI panel driver
Hi Paul, just a drive-by comment: On Sat, Aug 22, 2020 at 6:33 PM Paul Cercueil wrote: > + gpiod_set_value_cansleep(priv->reset_gpiod, 0); > + usleep_range(20, 1000); > + gpiod_set_value_cansleep(priv->reset_gpiod, 1); This implies that the reset line is active low. I would specify in the DT GPIO handle that it is active low and invert the above. So: reset-gpios = < 4 GPIO_ACTIVE_LOW>; gpiod_set_value_cansleep(priv->reset_gpiod, 1); usleep_range(20, 1000); gpiod_set_value_cansleep(priv->reset_gpiod, 0); > + priv->reset_gpiod = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); > + if (IS_ERR(priv->reset_gpiod)) { > + dev_err(dev, "Couldn't get our reset GPIO\n"); > + return PTR_ERR(priv->reset_gpiod); > + } This would then fetch the GPIO as asserted (device in reset) unless changed, but that may be the right thing to do actually. > +static const struct ili9341_pdata yx240qv29_pdata = { > + .mode = { DRM_SIMPLE_MODE(240, 320, 37, 49) }, > + .width_mm = 0, // TODO > + .height_mm = 0, // TODO When nothing else works and data sheets are incomplete I just take out a ruler and measure on the actual device. Yours, Linus Walleij ___ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: 答复: [PATCH v2 6/6] drm/panel: Add Ilitek ILI9341 DBI panel driver
On 07/09/2020 14:57, Paul Cercueil wrote: > > > Le dim. 30 août 2020 à 22:28, Sam Ravnborg a écrit : >> Hi Laurent. >> >>> > >>> > Please read the cover letter, it explains why it's done this way. The >>> > whole point of this patchset is to merge DSI and DBI frameworks in a >>> > way that can be maintained. >>> >>> I think this proves the point that the proposed naming is confusing. At >>> least a rename would be required. >> >> Do you have any inputs on the amount of rename we are looking into. >> Is this a simple s/struct mipi_dsi_device/struct mipi_dxi_device/ >> or something more? >> >> We should script the rename as it will tocuh a lot of files, >> and without a script we would chase this. But once it is scripted >> it would be trivial to perform. >> >> I did not look at this enough, but I had an idea that we >> would have do to a s/dsi/dxi/ in a lot of places. >> >> (dxi is my best proposal at the moment for something covering both dsi >> and dbi). > > dcs? > > Since DBI and DSI panels generally all use DCS commands. mipi_disp / mipi_display ? since it's all about mipi display interfaces with different transport protocols. Neil > > -Paul > > > ___ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel ___ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: 答复: [PATCH v2 6/6] drm/panel: Add Ilitek ILI9341 DBI panel driver
Le dim. 30 août 2020 à 22:28, Sam Ravnborg a écrit : Hi Laurent. > > Please read the cover letter, it explains why it's done this way. The > whole point of this patchset is to merge DSI and DBI frameworks in a > way that can be maintained. I think this proves the point that the proposed naming is confusing. At least a rename would be required. Do you have any inputs on the amount of rename we are looking into. Is this a simple s/struct mipi_dsi_device/struct mipi_dxi_device/ or something more? We should script the rename as it will tocuh a lot of files, and without a script we would chase this. But once it is scripted it would be trivial to perform. I did not look at this enough, but I had an idea that we would have do to a s/dsi/dxi/ in a lot of places. (dxi is my best proposal at the moment for something covering both dsi and dbi). dcs? Since DBI and DSI panels generally all use DCS commands. -Paul ___ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: 答复: [PATCH v2 6/6] drm/panel: Add Ilitek ILI9341 DBI panel driver
Hi Leon, Le dim. 30 août 2020 à 16:36, 何小龙 (Leon He) a écrit : +struct ili9341 { + struct drm_panel panel; + struct mipi_dsi_device *dsi; + const struct ili9341_pdata *pdata; + + struct gpio_desc*reset_gpiod; + u32 rotation; +}; + Hi Paul, you put the mipi_dsi_device inside the struct. I think it maybe not a good idea. That means the panel has a MIPI-DSI interface but it doesn't have actually. +static int ili9341_probe(struct mipi_dsi_device *dsi) +{ + struct device *dev = >dev; + struct ili9341 *priv; + int ret; + + /* See comment for mipi_dbi_spi_init() */ + if (!dev->coherent_dma_mask) { + ret = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(32)); + if (ret) { + dev_warn(dev, "Failed to set dma mask %d\n", ret); + return ret; + } + } + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + mipi_dsi_set_drvdata(dsi, priv); + priv->dsi = dsi; + + device_property_read_u32(dev, "rotation", >rotation); + + priv->pdata = device_get_match_data(dev); + if (!priv->pdata) + return -EINVAL; + + drm_panel_init(>panel, dev, _funcs, + DRM_MODE_CONNECTOR_DPI); + + priv->reset_gpiod = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(priv->reset_gpiod)) { + dev_err(dev, "Couldn't get our reset GPIO\n"); + return PTR_ERR(priv->reset_gpiod); + } + + ret = drm_panel_of_backlight(>panel); + if (ret < 0) { + if (ret != -EPROBE_DEFER) + dev_err(dev, "Failed to get backlight handle\n"); + return ret; + } + + drm_panel_add(>panel); + + dsi->bus_type = priv->pdata->bus_type; + dsi->lanes = priv->pdata->lanes; + dsi->format = MIPI_DSI_FMT_RGB565; + + ret = mipi_dsi_attach(dsi); + if (ret) { + dev_err(dev, "Failed to attach DSI panel\n"); + goto err_panel_remove; + } + + ret = mipi_dsi_maybe_register_tiny_driver(dsi); + if (ret) { + dev_err(dev, "Failed to init TinyDRM driver\n"); + goto err_mipi_dsi_detach; + } + + return 0; + +err_mipi_dsi_detach: + mipi_dsi_detach(dsi); +err_panel_remove: + drm_panel_remove(>panel); + return ret; +} + +static int ili9341_remove(struct mipi_dsi_device *dsi) +{ + struct ili9341 *priv = mipi_dsi_get_drvdata(dsi); + + mipi_dsi_detach(dsi); + drm_panel_remove(>panel); + + drm_panel_disable(>panel); + drm_panel_unprepare(>panel); + + return 0; +} + +static const struct ili9341_pdata yx240qv29_pdata = { + .mode = { DRM_SIMPLE_MODE(240, 320, 37, 49) }, + .width_mm = 0, // TODO + .height_mm = 0, // TODO + .bus_type = MIPI_DCS_BUS_TYPE_DBI_SPI_C3, + .lanes = 1, +}; + +static const struct of_device_id ili9341_of_match[] = { + { .compatible = "adafruit,yx240qv29", .data = _pdata }, + { } +}; +MODULE_DEVICE_TABLE(of, ili9341_of_match); + +static struct mipi_dsi_driver ili9341_dsi_driver = { + .probe = ili9341_probe, + .remove = ili9341_remove, + .driver = { + .name = "ili9341-dsi", + .of_match_table = ili9341_of_match, + }, +}; +module_mipi_dsi_driver(ili9341_dsi_driver); Again, you treat this driver as a mipi dsi driver but for a MIPI-DBI (I8080/SPI) panel device. That will make developers confused. Is it possible to just add a mipi_dbi_driver for I8080/SPI interface panel? Thanks! Please read the cover letter, it explains why it's done this way. The whole point of this patchset is to merge DSI and DBI frameworks in a way that can be maintained. Cheers, -Paul ___ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: 答复: [PATCH v2 6/6] drm/panel: Add Ilitek ILI9341 DBI panel driver
Hi Laurent. > > > > Please read the cover letter, it explains why it's done this way. The > > whole point of this patchset is to merge DSI and DBI frameworks in a > > way that can be maintained. > > I think this proves the point that the proposed naming is confusing. At > least a rename would be required. Do you have any inputs on the amount of rename we are looking into. Is this a simple s/struct mipi_dsi_device/struct mipi_dxi_device/ or something more? We should script the rename as it will tocuh a lot of files, and without a script we would chase this. But once it is scripted it would be trivial to perform. I did not look at this enough, but I had an idea that we would have do to a s/dsi/dxi/ in a lot of places. (dxi is my best proposal at the moment for something covering both dsi and dbi). PS. I am travelling for a few days, so do not expect quick responses. Sam ___ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: 答复: [PATCH v2 6/6] drm/panel: Add Ilitek ILI9341 DBI panel driver
Hi Paul, On Sun, Aug 30, 2020 at 06:48:12PM +0200, Paul Cercueil wrote: > Le dim. 30 août 2020 à 16:36, 何小龙 (Leon He) a écrit : > >> +struct ili9341 { > >> + struct drm_panel panel; > >> + struct mipi_dsi_device *dsi; > >> + const struct ili9341_pdata *pdata; > >> + > >> + struct gpio_desc*reset_gpiod; > >> + u32 rotation; > >> +}; > >> + > > > > Hi Paul, you put the mipi_dsi_device inside the struct. I think it > > maybe not > > a good idea. That means the panel has a MIPI-DSI interface but it > > doesn't > > have actually. > > > >> +static int ili9341_probe(struct mipi_dsi_device *dsi) > >> +{ > >> + struct device *dev = >dev; > >> + struct ili9341 *priv; > >> + int ret; > >> + > >> + /* See comment for mipi_dbi_spi_init() */ > >> + if (!dev->coherent_dma_mask) { > >> + ret = dma_coerce_mask_and_coherent(dev, > >> DMA_BIT_MASK(32)); > >> + if (ret) { > >> + dev_warn(dev, "Failed to set dma mask > >> %d\n", ret); > >> + return ret; > >> + } > >> + } > >> + > >> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); > >> + if (!priv) > >> + return -ENOMEM; > >> + > >> + mipi_dsi_set_drvdata(dsi, priv); > >> + priv->dsi = dsi; > >> + > >> + device_property_read_u32(dev, "rotation", >rotation); > >> + > >> + priv->pdata = device_get_match_data(dev); > >> + if (!priv->pdata) > >> + return -EINVAL; > >> + > >> + drm_panel_init(>panel, dev, _funcs, > >> + DRM_MODE_CONNECTOR_DPI); > >> + > >> + priv->reset_gpiod = devm_gpiod_get(dev, "reset", > >> GPIOD_OUT_HIGH); > >> + if (IS_ERR(priv->reset_gpiod)) { > >> + dev_err(dev, "Couldn't get our reset GPIO\n"); > >> + return PTR_ERR(priv->reset_gpiod); > >> + } > >> + > >> + ret = drm_panel_of_backlight(>panel); > >> + if (ret < 0) { > >> + if (ret != -EPROBE_DEFER) > >> + dev_err(dev, "Failed to get backlight > >> handle\n"); > >> + return ret; > >> + } > >> + > >> + drm_panel_add(>panel); > >> + > >> + dsi->bus_type = priv->pdata->bus_type; > >> + dsi->lanes = priv->pdata->lanes; > >> + dsi->format = MIPI_DSI_FMT_RGB565; > >> + > >> + ret = mipi_dsi_attach(dsi); > >> + if (ret) { > >> + dev_err(dev, "Failed to attach DSI panel\n"); > >> + goto err_panel_remove; > >> + } > >> + > >> + ret = mipi_dsi_maybe_register_tiny_driver(dsi); > >> + if (ret) { > >> + dev_err(dev, "Failed to init TinyDRM driver\n"); > >> + goto err_mipi_dsi_detach; > >> + } > >> + > >> + return 0; > >> + > >> +err_mipi_dsi_detach: > >> + mipi_dsi_detach(dsi); > >> +err_panel_remove: > >> + drm_panel_remove(>panel); > >> + return ret; > >> +} > >> + > >> +static int ili9341_remove(struct mipi_dsi_device *dsi) > >> +{ > >> + struct ili9341 *priv = mipi_dsi_get_drvdata(dsi); > >> + > >> + mipi_dsi_detach(dsi); > >> + drm_panel_remove(>panel); > >> + > >> + drm_panel_disable(>panel); > >> + drm_panel_unprepare(>panel); > >> + > >> + return 0; > >> +} > >> + > >> +static const struct ili9341_pdata yx240qv29_pdata = { > >> + .mode = { DRM_SIMPLE_MODE(240, 320, 37, 49) }, > >> + .width_mm = 0, // TODO > >> + .height_mm = 0, // TODO > >> + .bus_type = MIPI_DCS_BUS_TYPE_DBI_SPI_C3, > >> + .lanes = 1, > >> +}; > >> + > >> +static const struct of_device_id ili9341_of_match[] = { > >> + { .compatible = "adafruit,yx240qv29", .data = > >> _pdata }, > >> + { } > >> +}; > >> +MODULE_DEVICE_TABLE(of, ili9341_of_match); > >> + > >> +static struct mipi_dsi_driver ili9341_dsi_driver = { > >> + .probe = ili9341_probe, > >> + .remove = ili9341_remove, > >> + .driver = { > >> + .name = "ili9341-dsi", > >> + .of_match_table = ili9341_of_match, > >> + }, > >> +}; > >> +module_mipi_dsi_driver(ili9341_dsi_driver); > > > > Again, you treat this driver as a mipi dsi driver but for a MIPI-DBI > > (I8080/SPI) > > panel device. That will make developers confused. > > > > Is it possible to just add a mipi_dbi_driver for I8080/SPI interface > > panel? > > Thanks! > > Please read the cover letter, it explains why it's done this way. The > whole point of this patchset is to merge DSI and DBI frameworks in a > way that can be maintained. I think this proves the point that the proposed naming is confusing. At least a rename would be required. -- Regards, Laurent Pinchart ___ dri-devel mailing list
答复: [PATCH v2 6/6] drm/panel: Add Ilitek ILI9341 DBI panel driver
> +struct ili9341 { > + struct drm_panel panel; > + struct mipi_dsi_device *dsi; > + const struct ili9341_pdata *pdata; > + > + struct gpio_desc*reset_gpiod; > + u32 rotation; > +}; > + Hi Paul, you put the mipi_dsi_device inside the struct. I think it maybe not a good idea. That means the panel has a MIPI-DSI interface but it doesn't have actually. > +static int ili9341_probe(struct mipi_dsi_device *dsi) > +{ > + struct device *dev = >dev; > + struct ili9341 *priv; > + int ret; > + > + /* See comment for mipi_dbi_spi_init() */ > + if (!dev->coherent_dma_mask) { > + ret = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(32)); > + if (ret) { > + dev_warn(dev, "Failed to set dma mask %d\n", ret); > + return ret; > + } > + } > + > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); > + if (!priv) > + return -ENOMEM; > + > + mipi_dsi_set_drvdata(dsi, priv); > + priv->dsi = dsi; > + > + device_property_read_u32(dev, "rotation", >rotation); > + > + priv->pdata = device_get_match_data(dev); > + if (!priv->pdata) > + return -EINVAL; > + > + drm_panel_init(>panel, dev, _funcs, > + DRM_MODE_CONNECTOR_DPI); > + > + priv->reset_gpiod = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); > + if (IS_ERR(priv->reset_gpiod)) { > + dev_err(dev, "Couldn't get our reset GPIO\n"); > + return PTR_ERR(priv->reset_gpiod); > + } > + > + ret = drm_panel_of_backlight(>panel); > + if (ret < 0) { > + if (ret != -EPROBE_DEFER) > + dev_err(dev, "Failed to get backlight handle\n"); > + return ret; > + } > + > + drm_panel_add(>panel); > + > + dsi->bus_type = priv->pdata->bus_type; > + dsi->lanes = priv->pdata->lanes; > + dsi->format = MIPI_DSI_FMT_RGB565; > + > + ret = mipi_dsi_attach(dsi); > + if (ret) { > + dev_err(dev, "Failed to attach DSI panel\n"); > + goto err_panel_remove; > + } > + > + ret = mipi_dsi_maybe_register_tiny_driver(dsi); > + if (ret) { > + dev_err(dev, "Failed to init TinyDRM driver\n"); > + goto err_mipi_dsi_detach; > + } > + > + return 0; > + > +err_mipi_dsi_detach: > + mipi_dsi_detach(dsi); > +err_panel_remove: > + drm_panel_remove(>panel); > + return ret; > +} > + > +static int ili9341_remove(struct mipi_dsi_device *dsi) > +{ > + struct ili9341 *priv = mipi_dsi_get_drvdata(dsi); > + > + mipi_dsi_detach(dsi); > + drm_panel_remove(>panel); > + > + drm_panel_disable(>panel); > + drm_panel_unprepare(>panel); > + > + return 0; > +} > + > +static const struct ili9341_pdata yx240qv29_pdata = { > + .mode = { DRM_SIMPLE_MODE(240, 320, 37, 49) }, > + .width_mm = 0, // TODO > + .height_mm = 0, // TODO > + .bus_type = MIPI_DCS_BUS_TYPE_DBI_SPI_C3, > + .lanes = 1, > +}; > + > +static const struct of_device_id ili9341_of_match[] = { > + { .compatible = "adafruit,yx240qv29", .data = _pdata }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, ili9341_of_match); > + > +static struct mipi_dsi_driver ili9341_dsi_driver = { > + .probe = ili9341_probe, > + .remove = ili9341_remove, > + .driver = { > + .name = "ili9341-dsi", > + .of_match_table = ili9341_of_match, > + }, > +}; > +module_mipi_dsi_driver(ili9341_dsi_driver); Again, you treat this driver as a mipi dsi driver but for a MIPI-DBI (I8080/SPI) panel device. That will make developers confused. Is it possible to just add a mipi_dbi_driver for I8080/SPI interface panel? Thanks! Best regards This email (including its attachments) is intended only for the person or entity to which it is addressed and may contain information that is privileged, confidential or otherwise protected from disclosure. Unauthorized use, dissemination, distribution or copying of this email or the information herein or taking any action in reliance on the contents of this email or the information herein, by anyone other than the intended recipient, or an employee or agent responsible for delivering the message to the intended recipient, is strictly prohibited. If you are not the intended recipient, please do not read, copy, use or disclose any part of this e-mail to others. Please notify the sender immediately and permanently delete this e-mail and any attachments if you received it in error. Internet communications cannot be guaranteed to be timely, secure, error-free or virus-free. The sender does not accept liability for any errors or omissions.
[PATCH v2 6/6] drm/panel: Add Ilitek ILI9341 DBI panel driver
This driver is for the Ilitek ILI9341 based YX240QV29-T 2.4" 240x320 TFT LCD panel from Adafruit. v2: - Remove custom handling of backlight - Call drm_panel_disable() / drm_panel_unprepare() on module exit - drm_panel_add() is a void function now Signed-off-by: Paul Cercueil --- drivers/gpu/drm/panel/Kconfig| 9 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 318 +++ 3 files changed, 328 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 45b003752d65..38c581e91986 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -105,6 +105,15 @@ config DRM_PANEL_ILITEK_IL9322 Say Y here if you want to enable support for Ilitek IL9322 QVGA (320x240) RGB, YUV and ITU-T BT.656 panels. +config DRM_PANEL_ILITEK_ILI9341 + tristate "Ilitek ILI9341 320x240 QVGA panels" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for Ilitek IL9341 + QVGA (320x240) RGB, YUV and ITU-T BT.656 panels. + config DRM_PANEL_ILITEK_ILI9881C tristate "Ilitek ILI9881C-based panels" depends on OF diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index c01743cdc08b..d732c2b8a747 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c new file mode 100644 index ..8f32edaac627 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c @@ -0,0 +1,318 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * DRM driver for Ilitek ILI9341 panels + * + * Copyright 2018 David Lechner + * Copyright 2020 Paul Cercueil + * + * Based on mi0283qt.c: + * Copyright 2016 Noralf Trønnes + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#define ILI9341_FRMCTR10xb1 +#define ILI9341_DISCTRL0xb6 +#define ILI9341_ETMOD 0xb7 + +#define ILI9341_PWCTRL10xc0 +#define ILI9341_PWCTRL20xc1 +#define ILI9341_VMCTRL10xc5 +#define ILI9341_VMCTRL20xc7 +#define ILI9341_PWCTRLA0xcb +#define ILI9341_PWCTRLB0xcf + +#define ILI9341_PGAMCTRL 0xe0 +#define ILI9341_NGAMCTRL 0xe1 +#define ILI9341_DTCTRLA0xe8 +#define ILI9341_DTCTRLB0xea +#define ILI9341_PWRSEQ 0xed + +#define ILI9341_EN3GAM 0xf2 +#define ILI9341_PUMPCTRL 0xf7 + +#define ILI9341_MADCTL_BGR BIT(3) +#define ILI9341_MADCTL_MV BIT(5) +#define ILI9341_MADCTL_MX BIT(6) +#define ILI9341_MADCTL_MY BIT(7) + +struct ili9341_pdata { + struct drm_display_mode mode; + unsigned int width_mm; + unsigned int height_mm; + unsigned int bus_type; + unsigned int lanes; +}; + +struct ili9341 { + struct drm_panel panel; + struct mipi_dsi_device *dsi; + const struct ili9341_pdata *pdata; + + struct gpio_desc*reset_gpiod; + u32 rotation; +}; + +#define mipi_dcs_command(dsi, cmd, seq...) \ +({ \ + u8 d[] = { seq }; \ + mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d)); \ +}) + +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel) +{ + return container_of(panel, struct ili9341, panel); +} + +static int ili9341_prepare(struct drm_panel *panel) +{ + struct ili9341 *priv = panel_to_ili9341(panel); + struct mipi_dsi_device *dsi = priv->dsi; + u8 addr_mode; + int ret; + + gpiod_set_value_cansleep(priv->reset_gpiod, 0); + usleep_range(20, 1000); + gpiod_set_value_cansleep(priv->reset_gpiod, 1); + msleep(120); + + ret = mipi_dcs_command(dsi, MIPI_DCS_SOFT_RESET); + if (ret) { + dev_err(panel->dev, "Failed to send reset command: %d\n", ret); + return ret; + } + + /* Wait 5ms after soft reset per MIPI DCS spec */ + usleep_range(5000, 2); + + mipi_dcs_command(dsi, MIPI_DCS_SET_DISPLAY_OFF); + +