After reading Ron and Alan's posting this morning regarding the default
filters for Orion rigs, I decided to figure out why DX4WIN always selects
filter 2 in my Icom 756 Pro II and III when clicking on spots. For those who
have posed that same question here on the reflector, here's the answer:
Using Notepad, open "\RADIOS\ICOM 756 Pro.rig" and make the following change
under the heading [RC-Set Mode]:
DEFAULT - invokes filter 2:
CSTR=060002FD
For filter 1:
CSTR=060001FD
For filter 3:
CSTR=060003FD
-larry
K8UT
----- Original Message -----
From: "Alan Sewell" <[EMAIL PROTECTED]>
To: <dx4win@mailman.qth.net>
Sent: Saturday, December 31, 2005 18:56
Subject: Re: [Dx4win] ver 6 and Orion 2
> Ron,
>
> Open the file orion.rig located in the radios folder of the dx4win folder
> with a text editor.
>
> You may need to edit the MODES section to get it to go to the cw mode you
> want. On my Orion if I set CW=3,2;3,2;Y then when I click on a cw spot it
> goes to UCW. I prefer LCW so I have my line set to CW=2,3;2,3;Y. Don't ask
> me what it all means. I just experimented until it worked like I wanted!
>
> [MODES]
> AM=4;4;N
> CW=2,3;2,3;Y
> FM=5;5;N
> PACK=6;6;N
> SSB=1,0;1,0;N
>
> From the Orion software docs:
>
> ASCII ?0? (0x30) for USB mode
> ASCII ?1? (0x31) for LSB mode
> ASCII ?2? (0x32) for UCW mode
> ASCII ?3? (0x33) for LCW mode
> ASCII ?4? (0x34) for AM mode
> ASCII ?5? (0x33) for FM mode
> ASCII ?6? (0x34) for FSK mode
>
> I'm not sure how to set it up for RTTY though.
>
> 73,
>
> Alan N5NA
>
>
> ron.n9au wrote:
>> Double clicking on an obvious CW spot takes the radio to the proper
>> frequency but changes the mode from UCW to LCW.
>>
>> When clicking on a RTTY spot, the mode goes to USB
>>
>> In both cases, the QSO window mode is correct.
>>
>> Any help appreciated
>>
>> Ron N9AU
>>
>> _______________________________________________
>> Dx4win mailing list
>> Dx4win@mailman.qth.net
>> http://mailman.qth.net/mailman/listinfo/dx4win
>>
>>
>
> _______________________________________________
> Dx4win mailing list
> Dx4win@mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/dx4win
From [EMAIL PROTECTED] Tue Jan 3 08:58:07 2006
From: [EMAIL PROTECTED] (Tom Budde)
Date: Thu Jan 5 20:00:34 2006
Subject: [Dx4win] Awards
Message-ID: <!&!AAAAAAAAAAAYAAAAAAAAAKRm+JbOr6VMvc/[EMAIL PROTECTED]>
I had been looking through my log and it had assigned the wrong information
for awards, like WAS etc. I went and change the preferences and cleared all
the awards submissions.
Is there a way to have the program go back through the log and check for
contacts that apply to my new preferences or do I need to go through all of
them manually?
I could not find a way and I am thinking I will have to do it manually. I
have version 4.06.
Thanks for your help.
Tom Budde
KC8EGD
