I've decided to leave my K2 as a K2/100 and order a KAT100-1 to set it on.
So if anyone is thinking about adding the KAT2 or KBT2 to their K2 I am selling
my old cover. It has the KAT2 auto-tuner and the KBT2 internal battery option
installed. The KBT2 is less than 3 months old.
I'm
I have version 1.02 of the KSB2 firmware installed in my K2/100.
I have no intention of adding the K60XV. What changes have been made between
1.02 and 1.08?
I see mention that 1.04 added support for the KPA-100. I wonder what problems
the KPA-100 has when used with version 1.02 of
In a message dated 31/12/04 04:52:04 GMT Standard Time,
[EMAIL PROTECTED] writes:
Now to find out why the BFO range is too low. The BFO high frequency comes
in above the expected minimum of =4916.3 at 4918.2 The BFO low frequency
comes in above the expected maximum of =4912.7 at 4914.8
Should I use another procedure besides those posted?
Comments?
Chuck - n6dbt
Hi Chuck,
As one who did the alignment more times than I care to remember,
I can strongly recommend Toms newest set of alignment info. I
nailed my rigs filters with it (using my $25 hamfest laptop running
Stewart G3RXQ wrote:
It would be very helpful if someone could check
their K2/KPA100/KAT100 and see
if they get the same results.
Yes, my K2/KPA100/KAT100 does the same thing.
Thatr being said: I never tried the DISPLAY/TUNE
feature before to see what the rig will do full-bore,
nor would
On Fri, 31 Dec 2004 06:51:20 -0800 (PST), Steve Jackson wrote:
Stewart G3RXQ wrote:
It would be very helpful if someone could check
their K2/KPA100/KAT100 and see
if they get the same results.
Yes, my K2/KPA100/KAT100 does the same thing.
Thatr being said: I never tried the DISPLAY/TUNE
Stewart Baker wrote,
Since my original mail I have found that this anomaly only occurs when on
transmit, and is independent of whether RF is being generated or not.
I quite often vary my power during a transmission to get signal reports
on different station configurations e.g speech
Is the KX-1 capable of operating from twelve NiMh cells (~16-17V at full
charge?) without being damaged? Interested in using it self contained (six
AA NiMh cells) or with additional supply voltage (more cells) added
externally and wired in series with the internal cells, and wonder what the
One idea I have been working on is using the flat 10 AA holder from
Mouser, which can be rubber-banded or Velcro'd to the bottom of the
KX1. I got a few of them at $2 each. The 2x5 holders fit into my waist
pack, but are unwieldy in use. If I can figure out a way to carry the
10x1 holder in
Thank you Jim - I'll also post this to the group as well just to keep them
informed about where I'm at with testing. IF I can't get this thing aligned
completely, I may have to resort to bothering you with it next year when I
get back to Mobile.
I did the following tests and re-checked the
New Year's Greetings from mid-Missouri... where it's 65 degrees F with no
snow in sight! Not your 'typical Missouri New Year's Eve', that's for sure.
As a New Year gift (hopefully) to some of you, I just uploaded to my web
site at www.n0ss.net a PDF containing information describing how I
Well Gary, you cannot say I didn't warn you I'd be at it again asking stupid
questions! - Just completed my New Year's present to my self and ordered my 3rd
K2 - reckon I better keep this one when I'm done. Been over a year since I
burned some solder. You and Tom (aka) N0SS and all the rest
After 40+ years in ham radio, finally decided I needed a microphone for
the QRP SSB contests. Bought a Heil from Elecraft, installed the
resistor and now cant get more than ½ watt power when using PSK. Any
suggestions? Thanks!!
Mike KG4MTN
___
Hey all, K6KPH (KPH) is on the air for SKN @3545,7050,14050 and 21050. Send
QSLs to: Ms Denice Stoops PO BOX 381, Bolinas, Ca. 94924-0381
73s/Joe/KF6HAP
__
Switch to Netscape Internet Service.
As low as $9.95 a month -- Sign up
All I hear is noise on East coast but got in 3 stations from nearby states.
Ron wb1hga
Hey all, K6KPH (KPH) is on the air for SKN @3545,7050,14050 and 21050. Send
QSLs to: Ms Denice Stoops PO BOX 381, Bolinas, Ca. 94924-0381
73s/Joe/KF6HAP
___
Good Evening and Happy New Year!
My white paper is coming along quite nicely. Another ten pages or so and
it will be ready. This will free me up to finish my 80 meter loop. If
the snow stops it will be great weather for antenna raising. And kneeling
at the foundation to snake muddy ladder
Hi Don,
I agree, but as Mike, KK5F, pointed out, and I also noticed with my old
TS-830S and TS-140S, when using the same receive only phased loops both of
those rigs work fine at that low level and the K2, even with K2 preamp on,
doesn't.
It would be a better idea to put more gain in series with
17 matches
Mail list logo