yepper they have york pa up as well
Bob K3DJC
On Fri, 8 Jan 2016 02:32:44 + (UTC) Harry Yingst
writes:
Finally working again in Central NY
I have Verizon FIOS
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listin
Assuming that when the OP says "tuning" he is turning the VFO knob, then here's
my take. All of the worry about roofing filters (gad how I hate that term) is
for nothing. The crystal filters in conjunction with so-called hardware AGC are
there to protect the delicate 2nd mixer from overload in
Finally working again in Central NY
I have Verizon FIOS
From: "Eric Swartz - WA6HHQ, Elecraft"
To: riese-k3...@juno.com; elecraft@mailman.qth.net
Sent: Thursday, January 7, 2016 2:31 PM
Subject: Re: [Elecraft] Fw: Re: Elecraft Website Down
Bob - Are you also a Verizon custome
Check the K3S manual on cabling the P3 with the "Y" cable. I don't have the
manual handy but it is quite easy. USB cable to K3S and then the Y cable
connects to both P3 sockets and the RJ45 on back of K3S. Set K3S RS232 to USB.
Sent from my iPhone
...nr4c. bill
> On Jan 7, 2016, at 8:53 PM, J
How do I get my Frequency display back while using the usb cable to the
computer.
The P3 utility seems to be working. I seem to have the latest firmware
and utilities.
All I can find is the the frequency display on P3 works with rs232. It was.
I cannot get it with the CB3Y.
I checked the swi
Maybe. The K3 offers so many ways to configure things, not all
combinations are guaranteed to be optimal. You might also try not using
the dual PB DSP, my experience has been that MMTTY and 2TONE decode a
bit better without it. I have the "stock" 2.7 KHz filter, and a 5-pole
500 Hz. I norma
Wes - That was an inappropriate response and outside of the list guidelines.
Guys - ALWAYS keep it polite, even when you disagree.
Regards,
Eric
Moderator
/elecraft.com/
On 1/7/2016 1:09 PM, Wes (N7WS) wrote:
Go ahead and unsubscribe. I have no interest in the subject either, but I
have a De
OK Aaron,
Put it on a frequency on 40 tonight and post it. We all will listen for you.
Frank KG9H
> On Jan 7, 2016, at 5:47 PM, Dale Putnam wrote:
>
> Hi Aaron,
> I can relate.. the band is a bit different today..
> but if you have time.. I could meet up with you?
> Where are you calling?
>
Hi Aaron,
I can relate.. the band is a bit different today..
but if you have time.. I could meet up with you?
Where are you calling?
Have a great day,
--... ...--
Dale - WC7S in Wy
> Date: Thu, 7 Jan 2016 17:29:04 -0600
> From: k5atg.aa...@gmail.com
> To: elecraft@mailman.qth.net
>
I'm not sure if something is wrong or its my lack of experience. I just got
my K2 put together and sent it to Don to do some repairs and align it. Don
got it working good. I then got a Kenwood MC-43S microphone and hook it up
like Don told me to. I still have not been able to make a single contact
G'day,
Just downloaded the KIO3B installation instructions and in "Appendix A -
K144XV Cabling" page 16, the written reference to Figure 16 and 17 on
page 16 is the reverse of the illustrations Figure 16 and 17 on page 17.
Didn't notice if there was an errata, wasn't looking for one this earl
Hans,
That is very strange for such a condition to be present on only one
band. Are you certain it is not also present on 20, 17 and 15 meters?
If so, that would indicate a problem with the BFO for Upper Sideband.
The USB BFO is at a higher frequency than the other BFO settings, and it
may
Mike,
That effect should have nothing to do with the 1.8kHz filter.
I would go with Lyle's suggestion that it is the AGC that is allowing
you to hear the opposite sideband of strong signals.
To give that suspicion a quick check, turn off the preamp and add
attenuation, then reduce the RF Gai
Joe, et.al.,
I finally got back to the shack to check the setup. It looks like I was
actually using a 1.8 kHz SSB roofing filter in conjunction with the 500 Hz
dual PB DSP filter. I also checked the filter offsets which were all at
0.0 (all 8 pole) and I was using AFSK A mode. Is the effect I'm
Dear Elecraft
My K2 (# 7359) has been operating flawlessly SSB on all bands since dec 2013.
Suddenly for unknown reasons reception on 5343 kHz Upper Sideband seems to act
very strange.
On 60 meters and on this band only signals are coming in very loudly but seem
to be intermixed and disper
Go ahead and unsubscribe. I have no interest in the subject either, but I have
a Delete key.
On 1/7/2016 1:38 PM, David Davis wrote:
I really thought this thread was put to sleep.
While I feel for the users that are not able to access the Elecraft site. This
does not appear to be related to
I really thought this thread was put to sleep.
While I feel for the users that are not able to access the Elecraft
site. This does not appear to be related to use of this forum. The
technical issues causing the outage for a limited number of users is not
related to Elecraft or even their websi
Suggestion - try using a different DNS server.
Try the Google DNS server to see if that works.
It is 8.8.8.8 you can plug that into your network setting and you will
probably be able to get to the Elecraft.com website.
AI4CO
Randy Moore
-Original Message-
From: Elecraft [mailto:elec
still down in york pa
very amazimg !
Bob K3DJC
Thank you for all your feedback. Apparently, here in Southeast
Pennsylvania, something is fubar. I have reported the trouble to Verizon
and indicated a sample of the areas that are accessing Elecraft and those
that I know of that are not worki
Hello,
I called Elecraft this morning, Thu, Jan. 7 and the call went to voicemail so I
couldn't verify if their website was down or this is an external problem.
I used the DNS flushing method posted earlier and that did not make any
difference.
Anyone have any newer info?
73,
Rob W3OMW
_
20 matches
Mail list logo
