In the interest of reliving email overload for others, let's wind this OT thread
down now as its past 11 posts.
In general, please self moderate when getting up past 5 to 6 posts on OT
discussions.
73,
Eric
Moderator, I think.. ;-)
/elecraft.com/
On 4/19/2019 2:24 PM, Charlie T wrote:
There
You remember correctly. And they can require a tussle to separate on the bigger
sizes.
Wes N7WS
On 4/19/2019 1:13 PM, Kidder, George wrote:
If I remember rightly (and it's been a LONG time) there was an outer
shell pair made for at least some sizes which locked together external
to the shell
There is an easy locking device that can be added to any Cinch-Jones
connector.
The ones used on the older Yaesu radios had this device included.
You would have to practically destroy the chassis to get them apart if you
didn't squeeze it properly to dis-engage the lock.
Much tighter and higher cu
If I remember rightly (and it's been a LONG time) there was an outer
shell pair made for at least some sizes which locked together external
to the shell. Even without the lock, the multi-pin models (especially
in the larger sizes) took some umph to get them apart.
George, W3HBM
Bar Harbor, ME
For sale, a mint Elecraft K3s/100 built just over a year ago.
Radio includes a KFL3C-400 and neoprene soft grip for the VFO control.
Asking $2300.00 USD shipped.
73,
Dave
VE5UO
__
Elecraft mailing list
Home: http://mailman.qth.net/mailm
Because they are not locking and will separate if pulled, on more than
once occasion while I was snarfing around behind the desk and got my
foot tangled up in all the "wireless" down there, I did not pull the TX
off the desk. [:-)
73,
Fred ["Skip"] K6DGW
Sparks NV DM09dn
Washoe County
On 4/18
Thanks for everyone's interest in the K1. It has been sold.
tnx & 73, Doug -- KJ0F
On 4/18/2019 11:55 AM, Doug Person wrote:
I have an unfinished K1 for sale. It's about 80% done. I am unable to
finish it. 40/20 filter board.
Email direct for questions.
$300 shipped CONUS.
--
73 de Doug --
Sorry for the typo in the first line - the ETS2 is the standard 3 inch
tilt stand, the ETS15 is the 1.5 inch short tilt stand.
It is normally used with the KAT100 when the K2 is stacked on top of the
KAT100, but it can be used in other configurations as well - owner's choice.
73,
Don W3FPR
O
Don,
Thanks! Just what I needed, I put one on order.
73,
Gordon - N1MGO
On 4/19/2019 7:55 AM, Don Wilhelm wrote:
Gordon,
Yes, it is ETS2.
Go to the Elecraft website Quick Order, then open Classic Transceivers
and K2 Accessoriesl and cliick on ETS15.
73,
Don W3FPR
On 4/19/2019 6:00 AM,
recap: while using the freq utility with kx3: every time you QSY there is
a beep.
a beep in the headphones
a beep I cannot silence
-Original Message-
From: Wayne Burdick [mailto:n...@elecraft.com]
Sent: Thursday, November 16, 2017 08:19 AM
To: herr42
Cc: Ron D'Eau Claire; Elecraft Re
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
Gordon,
Yes, it is ETS2.
Go to the Elecraft website Quick Order, then open Classic Transceivers
and K2 Accessoriesl and cliick on ETS15.
73,
Don W3FPR
On 4/19/2019 6:00 AM, Gordon LaPoint wrote:
Is there a shorter K2 tilt stand available? I would like one that is
about 1/2 as high as the s
Is there a shorter K2 tilt stand available? I would like one that is
about 1/2 as high as the standard one. Its too low with the stand
folded and too high with it up.
Thanks,
Gordon - N1MGO
__
Elecraft mailing list
Home: http://ma
13 matches
Mail list logo