On 5/20/2021 2:50 PM, Andy Durbin wrote:
"I can hear a 6 meter beacon on Data mode, but when I switch to CW I get no copy at
all."
Does the K3, like the TS-590, have a user option that defines how the change to
CW is handled?
Not that I know of. In digital and SSB modes, the dial frequency
I just dialed up a local beacon. With it producing about a 1 kHz tone in
the tx data mode, I switched the mode on my k3 to CW. the tone dropped
down by 600 hz, which is the CW offset/sidetone point I have in my K3.
If you hear it on the tx data mode, and you move to CW, adjust the vfo
+/-
Different side bands?
> On May 20, 2021, at 4:52 PM, John Stengrevics
> wrote:
>
> I have an unusual phenomenon. I can hear a 6 meter beacon on Data mode, but
> when I switch to CW I get no copy at all. Any thoughts?
>
> 73,
>
> John
> WA1EAZ
>
Unfortunately not that simple Andy. When switching to CW mode, I tune around
to make sure that it’s not a shift causing this . But , no luck.
John
WA1EAZ
> On May 20, 2021, at 5:50 PM, Andy Durbin wrote:
>
> "I can hear a 6 meter beacon on Data mode, but when I switch to CW I get no
> copy
"I can hear a 6 meter beacon on Data mode, but when I switch to CW I get no
copy at all."
Does the K3, like the TS-590, have a user option that defines how the change to
CW is handled? The options are typically to keep the dial frequency the same
and shift where the RX is listening, or to
Oops - on my K3S
> Begin forwarded message:
>
> From: John Stengrevics
> Subject: Not Able to hear CW
> Date: May 20, 2021 at 4:51:54 PM EDT
> To: elecraft
>
> I have an unusual phenomenon. I can hear a 6 meter beacon on Data mode, but
> when I switch to CW I get no copy at all. Any
I have an unusual phenomenon. I can hear a 6 meter beacon on Data mode, but
when I switch to CW I get no copy at all. Any thoughts?
73,
John
WA1EAZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Good point. One needs to do a careful zero beat cal first, to make sure you
are in the ballpark. You can verify later by tuning to 9,999,998 and
counting the beats in 10 seconds. The number of beats on the two frequencies
should add up to 40.
Incidentally, by counting the number of beats in
Right above your unsubscribe message is an Unsubscribe link to click on.
:-)
Juste au-dessus de votre message de désabonnement se trouve un lien de
désabonnement sur lequel cliquer. :-)
73,
Alan. G4GNX
-- Original Message --
From: "Jack F6AJW"
To: Elecraft@mailman.qth.net
Sent:
Hi Jack,
We can't unsubscribe you, but you should be able to do it yourself here, at
the bottom of the page:
http://mailman.qth.net/mailman/listinfo/elecraft
If you run into any trouble, feel free to reply privately and I'll do my
best to help.
Cheers,
Julie
On Thu, May 20, 2021, 12:28
Please unsubscribe ; KX3 sold.
Tanks es 73's.
Jacques F6AJW
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted
Bill;
R22 in the sensors is a sense resistor that tells the controller which sensor
is attached. It is a very low stress part that sees at most 5 volts at very low
current. R22 is different for each sensor - the values shown in the schematic
are not necessarily correct. Also, these are
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
My W2 wattmeter suddenly stopped working properly this morning along with
that dreaded smoke smell. The smell came from the 2KW sensor unit and upon
inspection R22 which is a 1K in the sense circuit is burned. Of course
it's surface mount but I think I can replace it OK. If not with another
"I tune to 10,000,002 and adjust REF CAL for 20 beats in 10 seconds, or as
close to 20 as I can get, with the granularity of the ref cal steps."
Zero beat has only one solution. Doesn't your method have two solutions, only
one of which is correct?
73,
Andy, k3wyc
15 matches
Mail list logo