Re: [Elecraft] K2 Alignment and Test, Part II - No signal on TP3

2012-07-05 Thread Cameron Haines
as opposed to 8 - 10 Mhz. Any thoughts were I have gone wrong? Thanks, Cameron  AE5UZ From: Cameron Haines camhai...@yahoo.com To: David Moorman dmoorm...@comcast.net Cc: elecraft@mailman.qth.net elecraft@mailman.qth.net Sent: Tuesday, July 3, 2012 7:40 PM

Re: [Elecraft] K2 Alignment and Test, Part II - No signal on TP3

2012-07-05 Thread Cameron Haines
...@embarqmail.com To: Cameron Haines camhai...@yahoo.com Cc: elecraft@mailman.qth.net elecraft@mailman.qth.net Sent: Thursday, July 5, 2012 12:20 PM Subject: Re: [Elecraft] K2 Alignment and Test, Part II - No signal on TP3 Cameron, The first thing is to determine whether you have a problem

Re: [Elecraft] K2 Alignment and Test, Part II - No signal on TP3

2012-07-05 Thread Cameron Haines
looks well.  From: Don Wilhelm w3...@embarqmail.com To: Cameron Haines camhai...@yahoo.com Cc: elecraft@mailman.qth.net elecraft@mailman.qth.net Sent: Thursday, July 5, 2012 4:40 PM Subject: Re: [Elecraft] K2 Alignment and Test, Part II - No signal on TP3 Ok

[Elecraft] Alignment and Test, Part II - No signal on TP3

2012-07-03 Thread Cameron Haines
Hey Guys, Well, I am at the part where I need to test the 4 MHz oscillator calibration and ran into a snag. I am not getting anything on two different frequency counters when connected to TP3. Test up to this point have been good. Checked all the components around X1 and all look correct. No

[Elecraft] K2 Alignment and Test, Part II - No signal on TP3

2012-07-03 Thread Cameron Haines
Correction. Hey Guys, Well, I am at the part where I need to test the 4 MHz oscillator calibration and ran into a snag. I am not getting anything on two different frequency counters when connected to TP3. Test up to this point have been good. Checked all the components around X1 and all look

Re: [Elecraft] K2 Alignment and Test, Part II - No signal on TP3

2012-07-03 Thread Cameron Haines
Great suggestion. I can hear it a 4Mhz now.. from my Softrock SDR. Wonder why the Freq counters couldn't pick it up however. hmm. Thanks David! From: David Moorman dmoorm...@comcast.net To: Cameron Haines camhai...@yahoo.com Cc: elecraft@mailman.qth.net

Re: [Elecraft] K2 Alignment and Test, Part II - No signal on TP3

2012-07-03 Thread Cameron Haines
To: Cameron Haines camhai...@yahoo.com Cc: David Moorman dmoorm...@comcast.net; elecraft@mailman.qth.net elecraft@mailman.qth.net Sent: Tuesday, July 3, 2012 8:00 PM Subject: Re: [Elecraft] K2 Alignment and Test, Part II - No signal on TP3 Cameron, Read my last post carefully.  Then tell us whether you

[Elecraft] K2 Control Board U3

2012-06-23 Thread Cameron Haines
Finishing up this board today and run into a snag. U3 shows to be a LM6482 but I have only the 25lc320 left; is this part a substitute? I looked at part list but did see anything in regards to this part number. Many thanks, Cameron AE5UZ