Will there be in changes needed to the T1 itself? I have one on back order.
If it'll need any changes I'd rather wait for it to be updated before I get
it.
Also, any update on their status? Website still says ESD 1/25.
73 - Dave - N9PBJ
On Tue, Jan 26, 2021 at 9:28 AM Wayne Burdick wrote:
>
Hey Michael,
Yes Fldigi can control the KX3.
In Fldigi go to Configure, Rig Control.
Click on the Hamlib tab
In the Rig: drop down, select Elecraft K3/KX3 (Beta)
then in Device: select the port that is connected to the KX3 (not the signalink)
Make sure the baud rate is set correctly. If you're
Howdy All,
So on my PX3 I'm seeing the issue listed in the manual as Dip in Spectral
Response Close to VFO Frequency. Described as:
I/Q demodulation at baseband (used by the PX3 and many SDR applications) may
introduce small, very narrow-band amplitude variations in the response close to
I've been wanting to pick one of these up for a while, but didn't have the
means.
Have seen several of these listed for sale lately, but had to wait for a bonus
check.
Just curious if anyone has one they're wanting to sell before I order straight
from Elecraft.
73's Dave
N9PBJ
Are you by chance tuning in to the opposite sideband signal? That would show
weaker.
-Original Message-
From: Jeff Herr her...@comcast.net
Sent: Sunday, August 24, 2014 9:58am
To: elecraft@mailman.qth.net
Subject: [Elecraft] KX3 XG3
when I cable the xg3 to the kx3, and set the mode to
When going through the menus, if I try scrolling through the options for
ACC2 IO and I get to LO=PTT, the radio freezes. I have to remove a
battery to get it to shut down.
Nothing is plugged in to the ACC2 jack. I'm on MCU 1.87 and DSP 1.28
-Dave
I have ubuntu 14.04, 64bit, and the elecract kx3 utility working...
Here's how I installed ia32-lib:
|sudo -i
cd /etc/apt/sources.list.d
echo deb http://archive.ubuntu.com/ubuntu/ raring main restricted
universe multiverse ia32-libs-raring.list
apt-get update
apt-get install ia32-libs|
rm
I have a MFJ 1622 and am on a 2nd floor apartment. It actually works
quite well clamped to my balcony railing, as long as the counterpoise is
run out correctly. That's actually the biggest problem with my area.
It's a bit hard to hide the counterpoise since it has to go down to the
ground
Howdy,
So some of the menu options have a basic setting, ie on/off, but then an
extended setting as well. For example the Alarm menu:
MN000;
When read with MP; it will only report if the alarm is on or not (Bit 4
on / off)
you can turn it on or off by changing that bit with MP, and you can
I'll answer my own question.
Once that menu setting is active, DS; command will return what the
display is showing.
-Dave
On 5/20/2014 3:53 PM, David Patino wrote:
Howdy,
So some of the menu options have a basic setting, ie on/off, but then
an extended setting as well. For example
= source2[2:12].replace('@','').zfill(10)
freq
'01.200.325'
Thanks for all the replies!
-Dave
-Original Message-
From: Bill Noyce wbno...@gmail.com
Sent: Friday, May 16, 2014 1:18pm
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Programmers Reference Questions
David Patino asks
So I'm writing my own little rig control / configuration utility for the KX3.
But had a question on the DS command.
The programmer's reference manual states this about the text data:
TEXT and decimal point data: This field contains 8 bytes, with values 0x30 -
0xFF (hex). The first byte is
Does performing an EEINIT on the KX3 erase calibration information, mainly the
Receive Sideband calibration for use with the roofing filter?
In the documentation it recommends writing down the settings when you do it
yourself for future reference, but by any chance does the factory keep
I would shy away from putting a KX3 on a motorcycle for several reasons:
Heat from direct sunlight
Heat from higher ambient temperature on the road
Possible exposure to water / moisture
Vibration (Even on a 6 cylinder Goldwing this can be an issue)
Attempting to operate the relatively small
14 matches
Mail list logo
