Hi Elecrafters,
I am triyng to write 2 macros to switch between 100W output power and power
set by band.
100W ouput power is simple : PC100;
Unfortunatly I found no way to make sure I am on nor or per band in PWR
SET menu.
It's easy to access to PWR SET menu : MN081; but the parameter seems
Hi to the group,
I would like to know if the KRC2 can be used to interface a Kenwood rig to the
KAT500.
The KRC2 can read the Kenwood RS232 protocol and know its frequency.
The KAT500 needs a BCD code to switch bands (with the K3 it gets it from the
Aux connector).
The KRC2 has a connector
Message original
Objet : Re: [Elecraft] KRC2
De : Georges Ringotte F6DFZ f6...@sfr.fr
À : e...@elecraft.com
Cc :
Hi Eric,
Thanks for your answer and happy to be in direct contact with you.
As I said in my post, I read the KAT500 manual.
What I want is an ATU who switch
Hi to Geoff and to the Group,
Geoff said :
Although the Hilberling PT-8000 series of transceivers are very expensive,
this could be because they have been designed for Military and 'commercial'
use and not only for amateurs. I believe that it should be possible to
design and market a high
Hi to Geoff and to the Group,
Geoff said :
Although the Hilberling PT-8000 series of transceivers are very expensive,
this could be because they have been designed for Military and 'commercial'
use and not only for amateurs. I believe that it should be possible to
design and market a high
Out of an extremely interesting private mail, I don't have got comments on
this topic, which was much debated in the past.
I post it once again because I think the Elecraft team and Elecraft
aficionados are more apt to discuss this subject than on other reflectors
dealing with down
Message original
Objet : Re: [Elecraft] Down or Up conversions designs
De : Georges Ringotte F6DFZ f6...@sfr.fr
À : n...@sonic.net
Cc :
Hi Alan,
Happy to meet the Elecraft firmware guru!
Many thanks for your fine comments.
I perfectly understand the Elecraft policy, I
Hi to the group
Even though I own and appreciate very much my K3, in fact I believe it's the
best sounding receiver I ever had, I have always been an advocate of up
conversion design, namely because it's the only way to get general coverage and
also because some characteristics, for a given
Hi to the group
Just to report a problem I had very recently.
My K3 is used with a Turner +3 microphone and had been working very fine since
the beginning.
Yesterday, barefoot at 90 W or at 350 W with my PA, I had very bad modulation
reports on 40 m.
I switched on the monitor, and indeed
Hi to the Elecraft team and the group,
Will this ATU be used with the K3 as the internal tuner (automatic band change,
automatic antenna selection with band, automatic ATU settings with
frequency...)
Is the diversity option still in the pipe?
Best regards
Georges Ringotte
F6DFZ
Hi to the group,
I read with great interest the KX3 user manual.
Two questions to the Elecraft team.
The KX3 home use is clearly envisaged. In a vast majority of cases, you need to
have a near vertical front panel to operate ergonomicaly a rig.
Do you plan to sell a stand, like the one for the
Hi to the group,
On a similar subject, could the P3 screen be used to display some information
from the K3 (for exemple the sub-receiver status) ?
Best regards
Georges
__
Elecraft mailing list
Home:
Hi to the group,
Is it possible to write a macro command switching on or off the AF peak filter ?
I do not see anything in the programmer reference document.
Best regards
Georges
__
Elecraft mailing list
Home:
Thank you for the answer !
Found how to get the AF peak filter Off on the sub receiver !
Regards
Georges
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Hi to the group,
Same thing there, impossible to have the P3 showing the beginning of a band, it
shows 99.5 kHz, or anything.
That was not the case with previous version.
Any help ?
Georges
__
Elecraft mailing list
Home:
Hi to the group,
Grab a K2 kit and/or its options as soon as you can.
Through hole components become more and more scarce, and I believe will come
a time
when Elecraft will announce they can no more produce these kits.
OHR, Wilderness Radio and others have such difficulties.
Regards
Georges
Hi to the group,
I have a question about the S meter calibration.
On HF bands, It's on spot, very impressive indeed from S1 to end of scale,
tracking my HP generator nearly perfectly ; S9 at -73dBm
However, it's not the same with the internal K144XV 2 m transverter.
P3 is good, -93 dBm at S9.
! There are
no enormous filter caps in either Kn machine that need to be serviced at
power on. Seems to me that using a non-matched pair of transistors is
much more likely to be the cause of failure, as someone has already
pointed out.
John Ragle -- W1ZI
=
On 2/17/2011 2:31 AM, Georges Ringotte F6DFZ
Hi to the group,
When I had my K2/10, I had multiple failures of the PA transistors.
Close investigation showed that the problem came from my switching power
supply (a professional 5A one from Friwo).
When switching on the K2, the power supply emited large spikes that
destroyed the PA
Hi to the group,
You can use the FT-2000 with the P3 in fitting inside the IF-2000 board from RF
Space, and configure the P3 on the IF out frequency of this board.
Georges
__
Elecraft mailing list
Home:
My K3/P3 are on their way to France with USPS Priority Mail International.
Who will distribute them to my door : La Poste, GLS ???
Thank you.
Georges F6DFZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Hi to the group,
Here is a post I made on the TS-590 Yahoo Group about down or up conversion,
close spaced signals dynamic range, and the
way receivers are classed in a few charts (Sherwood or W8JI for exemple).
I ordered very recently a K3, and it is on its way to France.
I must add that
22 matches
Mail list logo
