Hello List and Robin,
Robin asked for some of my settings that I use on my K3 regarding the
new NR in Firmware 3.27, and I thought that it may help the Group to
post them here.
These are answers to Robins questions, so keep this in mind.
AND...I use my K3 almost 100% as an IF for VHF Bands, so
Hi Guys,
I have just upgraded to the latest Beta release, using the new NR algorithm.
In my opinion, it is the best it has ever been ! My only qualifier...I
only operate SSB mode.
73
Glenn
VK4BG
__
Elecraft mailing list
Home: http://
Hello Guys,
K3 Serial Number 63, located in VK Land, is up and working.
After an initial Hiccup at the Synthesiser Calibration Step that was
cured by a Firmware Upgrade, all is well. I posted a question to the
Support Email Address about the Error Code I received, and within a few
minutes, W
Hi Group,
At Last !
The Big White Box arrived about 10 minutes ago, containing Serial Number
63 ( A K3/10 Kit ).
I'll be busy for a while
73
Glenn
VK4BG
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to po
Hi Group,
Well, at last...my K3/10 has arrived in VK...delivery now Monday next
week according to UPS ( I'm quite a distance from Sydney, where the K3
will be spending the Weekend ). Many thanks to the overworked Lisa, who
is doing a fantastic job to satisfy a lot of very keen expectant K3 Own
G'Day Guys,
I've got a situation that I cannot find the answer to.
I have a K2/100 that I now have ( was performing HF Serive only until
recently ) interfaced with a XV50/XV144/XV432 and a KAT100 and Computer. As
an HF performer, it was and still is great. As a stand alone K2/100
interfaced with
Hi Group,
I'm presently running a K2 as an IF ( 28 Mhz ) and two Elecraft
TRansverters...the XV50 and the XV144 ( and hopefuly the XV432 soon ??? ).
I have the System hooked up using the Daisy Chain Control cable as per
the instructions in the XV Transverter Manual. I use a Station Sequencer
Hi Gang,
I've got a problem with my K2/XV144 combination when using a Linear
after the XV144. I've setup the combination correctly ( I think) and it
works fine barefoot...max power of 5w from the K2 to drive the XV144
easily gives me 25w plus out on 144 Mhz
As soon as I hook up my 4CX800 Lin
Hi Group,
I'm just at the Test and Alignment Part II Stage on my Second K2.
Up until now, all smooth sailing.
On doing the PLL Ref Oscillator Test however, I come up with 12.100.48
kHz for the high frequency and 12.091.64 for the low, giving me a range
of 8.84 kHz..which, according to the ins
Hi again Group,
Well, my K2 is 100% after all. In less then 30 minutes from my posting,
I had help at hand from no less the 3 Elecrafters who quickly put me
right. My fault in not actually looking at the BFO freq's as I ran CAL
FIL using Spectrogram...I cunningly put the BFO on the wrong side
Hi Group,
I thought that my recently finished K2 had come through test and it's
forst operational period with flying colours...I was wrong.
I have just discovered, due to todays activities, that my K2 does not
apparently switch to LSB...the annunciator does, but the radio doesn't.
I have ju
Hi Group,
I've just recently finished a K2, S/N 4630. It has DSP, SSB, 160M
Option,KI02 and the K60XV.
All appeared well until today, when I noticed that tapping the DISPLAY
Button from the frequency display to the DSP Menu, I get a cyclic
beep...or burp. It changes frequency from DSP on to
Hi Group,
K2 Serial Number 04630 sprang into life here over the weekend...just
under a week from receiving a parcel with the K2, an XV50 and an XV144.
It was a great experience, and full marks to the Elecraft Crew for an
excellent product and fantastic documentation. Very little head
scratchi
Hi Group,
I've just finished an XV144 Transverter for another Ham who lives just
down the street for me while I'm waiting for my K2 to clear VK Customs (
Bummer ).
We fired it up today and all went well...very well in fact, but one
thing I did notice with the counter plugged into the 144 Mhz
14 matches
Mail list logo