[Elecraft] RE: Receive antenna connection

dered. http://www.grove-ent.com/ANTADAP.html 73, Mike K2MK [Elecraft] Receive antenna connection Joe Hoffman Tue, 30 Dec 2008 12:32:26 -0800 I have a K9AY receive loop to connect to my K3. The K9AY box needs a RCA phono plug. I'm afraid I don't recognize what the plug is on the KX

RE: [Elecraft] K3 and MixW audio input volume

t; but you also have to consider the setting on your PC line-in. And check the back of the K3 to be sure the line out plug is actually plugged into the line out jack and not the headphone or speaker jack. 73, Mike K2MK RE: [Elecraft] K3 and MixW audio input volume Greg Sat, 27 Dec 2008 16:3

[Elecraft] RE: K3 250Hz Filter gain maxed yet low

positive. Instead, set those undesired frequencies negative and leave the desired frequencies at zero. I tried this on my unit and it absolutely was the case. 73, Mike K2MK ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a

[Elecraft] Re: Transmit when switching from DATA to AM mode?

Hi Joe: Consider the possibility of it being the software program you are running on your PC in DATA mode. Quit the program first then switch to AM. It's frequently a safe bet to blame the computer for anything that goes wrong. 73, Mike

[Elecraft] Re: K3 Subreceiver ANT selection doesn't work - always uses the AUX antenna

BSET display. So Frank's problem in BSET is unique to his K3. Mike K2MK Re: [Elecraft] K3 Subreceiver ANT selection doesn't work - always uses the AUX antenna Barry N1EU Thu, 25 Dec 2008 06:46:31 -0800 K2MK wrote: Maybe it's a bug in the code. The sub antenna can be changed f

[Elecraft] Re: K3 Subreceiver ANT selection doesn't work - always uses the AUX antenna

UX as you left it when you changed it with BSET off. Maybe it's a bug in the code. The sub antenna can be changed from the main display only not from the BSET display. 73, Mike K2MK Re: [Elecraft] K3 Subreceiver ANT selection doesn't work - always uses the AUX antenna Frank

[Elecraft] Re: RTTY using LSB versus AFSK-A

e bandwidth for that one signal. So I'm basically using MixW to autospot the signal using its AFC and then move the signal into the center of the K3 filter passband. I suppose it would be better if I fully understood what I was doing. But why p

[Elecraft] Re: RTTY using LSB versus AFSK-A

Mode instead of LSB assuming both bandwidths are set the same. Mike K2MK ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http

[Elecraft] RTTY using LSB versus AFSK-A

ide in my decision to use MixW. Mike K2MK ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Hel

[Elecraft] MixW settings for K3

MixW reflector and found the suggested settings of: RTS set to PTT DTR set to CW MixW now works properly in digital modes and will not erroneously activate transmit if the K3 is in the wrong mode. It does transmit CW properly in the MixW CW mode. 73, Mike

[Elecraft] RX EQ comments

or CW and another for SSB. It seems like there should be unique settings for the different modes. Mike K2MK ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change

Re: [Elecraft] Split while using Diversity

n you turn off SPLIT, the VFO B display returns to the original frequency. Thanks for the clarification. 73, Mike K2MK -- From: "Ed K1EP" <[EMAIL PROTECTED]> Sent: Wednesday, December 03, 2008 6:14 PM To: "K2MK" <

[Elecraft] Split while using Diversity

I see this working is to use XIT instead of split. I'm just not a fan of XIT. So am I missing something? 73, Mike K2MK ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info

<    1   2   3   4   5   6