KPA500 shut off with a bang while operating RTTY @300W.
Antenna is a steppir beam.
On opening the KPA500,found 2 ceramic? caps of VRF2933
adrift with underside of the said caps,black.
Have written to support.Is this the first time this has happened
in a KPA500?
73 and HNY,
Nandu
VU2NKS
Hi All,
KPA500,S/no:1778 was being operated on RTTY at approx.320W.
Antenna is a steppir beam.
Heard a loud DHOOP sound and the amp.went off.
Fuses intact.Opened the top and left side panel,nothing
seen as far as I can make out.
What should I be looking for?
73 and HNY.
Nandu
VU2NKS
Lid of the AC power entry module has broken and is in my hand.
Entirely my doing.
Will the fuse holder fall out while I am looking for a replacement?
Nandu
VU2NKS
__
Elecraft mailing list
Home:
KPA500 s/n-1778 Factory assembled.
This morning noticed the blank but lit LCD screen mid-ops.
The amp.is working ok except for the blank screen.
Amp. amplifies,switches bands etc;used with K3
None of the I/O ports connected.
I see that this problem has been reported on the list but has
gone
Story of my new K3
Location Date Local Time Activity Chek Lap Kok, Hong Kong 08/12/2012 4:55 The
package is being held for intercept processing Anchorage, AK, United
States 07/12/2012 10:14 Departure Scan
07/12/2012 6:52 Arrival Scan Louisville, KY, United States
07/12/2012 4:10
) try to simplify it.
Firmware load is done at 38400 bps.
73 de Dick, K6KR
On Dec 3, 2012, at 5:21 AM, Nand Kishore vu2...@gmail.com wrote:
What should be the time taken to do an upload for a K3 with subrx.
In my case its about 70 minutes.Is this normal ?
Nandu
Vu2nks
K3 # 282
...@comcast.net wrote:
Has that serial path worked more quickly in the past? Do you have
alternatives available to try? That load time is terrible v
Dick
On Dec 3, 2012, at 7:56 AM, Nand Kishore vu2...@gmail.com wrote:
Hi Dick,
I have been battling with an ERR TXG problem. I am in touch
wrote:
Make sure you have the latest version of the K3 Utility.
Fred Cady
fcady at ieee dot org
-Original Message-
From: elecraft-boun...@mailman.qth.net [mailto:elecraft-
boun...@mailman.qth.net] On Behalf Of Nand Kishore
Sent: Monday, December 03, 2012 9:31 AM
To: Dick
Hi All,
I have a K3/100 with following addons
1) KRX3
2) KXV3
3) KBPF3 on main Rx.
4) KPA3
No internal ATU.
I am trying to trouble-shoot ERR TXG fault with Support(Gary).
I have already replaced LPA with no change of ERR TXG.
I have been asked to use rf probe and give some readings.
I would
Hello,
I have a K3 #282 which is used on CW and FSK via 2 serial port
pcmcia card in a laptop.
I have been using this combo for last 2 years without any
problem,alternating between CW and
FSK using MixW(reg).
Last week I came back from IOTA AS-175 where this combo was used flawlessly.
I have worked Bob,KP2/W1EQ on 10m.
Got qsl on LoTW too.
100W K3/100 into 3el Steppir.
Nandu..VU2NKS
K3/100 #282
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Any news of KPA-500 assy.manual.
73,Nandu
K3 # 282
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
K3/100 #282,worked 5 bands,3 modes and 9 slots.
17m,20m,30m,40m and 80m.Higher bands not heard.
Power 100W. Antenna--80m almost full-size dipole.
My 3el Steppir is temp.qrt,awaiting spares.
I do have sub-rx with 400Hz in both rx. Also P3.
Depending on Dx locn. 2nd rx is of no use if you
cannot
Yesterday,while chasing ZL8X on various bands and modes,on 40m LSB
I could not get RX audio.Changing to USB got the audio back.
Checked on other bands,toggling between usb/lsb gives dead silence
on lsb.
RF gain wide open.Af gain same all bands and modes.AGC-F. Filter
as wide as can go.No VOX
Ordered as a kit on 16th April.Assembled on 28th Sept.Took one hour to
assemble.
Worked right away.
I had a FT-840 before K3,so no exposure to any kind of pan display.Lots to
learn.
73 de Nandu..VU2NKS
__
Elecraft
Did a K3DSPLPF mod along with an addition of Xtal filter in KRX3.
Also did SS H/W change.
At the closing phase noticed a capacitor fallen on work table.
Went ahead with assy.after looking for a missing capacitor in
available visible areas.Gave up looking after an hour.This was
yesterday night.K3
The capacitor does show that it had been soldered.
Nandu
VU2NKS
I cannot believe that a capacitor would actually come
unsoldered and fall
off a pcb; it's more likely that it was packed loose for some odd reason and
just happened to drop
I presume my K3 has a Rev.B DSP board.This is my 'only' radio.
I cannot disable K3 for any duration either for swap-out of dsp to
bring it to Rev.D status or go through the hassle of getting a current
dsp board with a lead time of whatever and shipping back removed
dsp board.
So, can I install
Hi All,
Those with P3 in hand.
Have you got SS hardware or normal h/w ?
If possible,I would like to start of with SS h/w
at the outset instead of retrofit at a later date.
Have got mail for P3 confirmation,placed order
on 16Apr'10.
73 es GD DX,
Hi Don,
I had a failure of RS 232 port in my K3 # 282.Had to change KIO3
board.
From reporting the defect to change of board took one week.For me,whatever
defect I encounter in my K3,shipping the whole rig to US is not an option.
I was given an option of changing U1 but I did not 'cos
Hi All,
I have a problem with my K3/100 #282.
Background:I use Mixw for cw/digimodes.Last week I lost
com port,could get it back only by reseating the usb
connector on the laptop.Had to do this every operating
session.Did'nt matter if I switched on the laptop first
or K3.
On 22/06 night I switched
Rec'd invoice #47805 for K3/100 kit for order with
deposit dated 14May'07.
KRX3 on backorder.
Nandu.
VU2NKS
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info
22 matches
Mail list logo