[Elecraft] K3: Noise Reduction in Data Modes

Just trying confirm this. The noise reduction function does not function while in any of the data modes? When I press NR, I get N/A on the VFO B display. Regards, Tedd K6OI ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a

[Elecraft] RE: K3: ERR TXF

Oops. Just searched the archives and realized it was a filter assignment error. Sorry for the bandwidth. Regards, Tedd K6OI ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info

[Elecraft] K3: ERR TXF

I get this error when transmitting. Happens on all bands into a dummy load. It was transmitting fine last night. BTW thanks to all who helped me on the KAT3 tuning question. Regards, Tedd K6OI ___ Elecraft mailing list Post to:

[Elecraft] KAT3 - Antenna tuned or not?

I am attempting to tune a Zero-Five Vertical with the KAT3. How do I determine if the KAT3 has found a match? I see the SWR on the K3 close to 1:1and full power out but my external SWR meter is still 5:1. Thanks. ___ Elecraft mailing list Post to:

Re: [Elecraft] [K3] Boot Camp / Windows XP experiences

Hi Toby, I don’t have my K3 “yet” but I am currently running an Icom ic-7000 with HRD under both boot camp (physical XP partion) and VMware Fusion (virtual XP) on my Macbook Pro. Both configurations work well but very dependent on the USB – Serial Converter cable used. I also run MacloggerDX

[Elecraft] K3 - Generating RTTY

I know that the K3 can output RTTY from CW generated from a set of paddles via the built-in keyer. But can it work with a CW keyboard (e.g. K1EL K40) which would key the K3’s “key” jack? Page 32 in the manual only mentions paddles and the internal keyer. I’m searching for a cheaper

[Elecraft] (no subject)

For Sale: Elecraft K2 QRP transceiver with SSB (KSB2) and DSP (KDSP2) option. Late serial number of 5108 therefore has all the updates and latest firmware. All expertly built and aligned by an electronics engineer. Altogether would list new for $957. I will also include a Plantronics

[Elecraft] For Sale: K2 + KSB2 + KDSP2

Hi, I have for sale a K2 with KSB2 and KDSP2. It is nicely built and aligned. It is serial number 5108. Asking $850 insured and shipped to CONUS. Paypal OK. Thanks for looking. Theodore W. Wong K6OI [EMAIL PROTECTED] ___ Elecraft mailing list

[Elecraft] FS: KX1 with Options

I still have for sale a fully built and tested KX1 with KXPD1 paddles, KXB30 30 meter, and KXAT1 antenna tuner. I will also include a BNC to Binding Post adapter and 6 lithium batteries. $365 shipped to CONUS. Please respond off the list to [EMAIL PROTECTED] Tedd K6OI

[Elecraft] FS: KX1 Built and Fully Loaded

KX1 KXB30 KXAT1 KXPD1 Purchased in Oct. 2005. $365 shipped CONUS. Paypal preferred. Tedd K6OI ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.):

RE: [Elecraft] Low BFO Output

at the internal speaker was low as well. Using the XG2, I now measure an MDS of -135.6 dbm. A big thanks to all on the reflector who helped, especially Don, W3FPR and Gary @ Elecraft. Tedd K6OI From: Don Wilhelm [EMAIL PROTECTED] Date: 2005/12/24 Sat PM 01:43:39 PST To: Tedd Wong [EMAIL PROTECTED

[Elecraft] Low BFO Output

First some history. During the BFO test, I discovered my BFO range was low. My upper frequency was 4917.55 and lower frequency was 4914.26. After much consultation with Gary, I tried the various tricks such as padding C174 and C173, adding caps to the junction of X3 and X4, and even adding

RE: RE: [Elecraft] K2 BFO Test

I just added the pad capacitors to c174 and c173. It helped but not enough. The high freq. is now 4917.37 and low is 4913.92 for a range of 3.45 kHz. Is it possible to get new crystals from Elecraft if indeed I do have the ones with the higher Q? Thanks From: Don Wilhelm [EMAIL

[Elecraft] What we have here is a failure to oscillate.

Help! I just finished the XG-2 and I get no output. As a veteran of a K2, KX1, and another K2 almost completed, I am humbled by this dilemma. I welcome your troubleshooting advice. regards ___ Elecraft mailing list Post to: