Where do I find the Elecraft Reflector?
It seems to have been lost in the dust.
> To: elecraft@mailman.qth.net
> From: n...@contesting.com
> Date: Mon, 22 Feb 2016 08:50:15 -0500
> Subject: Re: [Elecraft] OT: CW Contest logging question
>
> Can this thread please go back to CQ-Contest where
Maybe you put the K3 in split mode?
Tom wa4ta
To: elecraft@mailman.qth.net
From: vetteresto...@gmail.com
Date: Thu, 27 Aug 2015 12:08:39 -0700
Subject: [Elecraft] K3 Mic LED Orange
Hello All:
I just installed the DVR in my K3 and now the LED above the mic control
is orange and
I use one of these power supplies with a battery backup module installed
(Model: SEC-1223BBM). I have a deep cycle battery attached to
it.http://www.samlexamerica.com/products/ProductDetail.aspx?pid=516The
hot-switches to battery is very nice when power fails. Also if you happen to
draw more
Yes that or hit the ATU TUNE button on the K3 to tune the KAT500.
Tom wa4ta
Date: Fri, 14 Nov 2014 11:07:19 +0100
From: p...@xs4all.nl
To: elecraft@mailman.qth.net
Subject: [Elecraft] KAT500 tuning in combination with K3
Dick,
Now that you are 'on the air'...
Pressing the tune button
Also how did you fix it?
Tom - wa4ta
Date: Wed, 16 Jul 2014 09:59:20 -0700
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] Elecraft] K3 receiver troubleshooting
From: elecraft@mailman.qth.net
Thanks to all who offered helpful suggestions. They were all via email -
you
notice there
Why not just look at the P3 display? Don't you need that to have the P3 SVGA?
I don't have a P3.
What about using a Softrock Lite IF to a USB sound card on the Macbook Air?
The Softrock Lite is about $22 but you have to build it. You could also get a
LP-Pan2, but you already have the P3 so
Here are some of my resources I used for learning starting in January of 2014.
A lot of it was already mentioned.
First note: Spend 25% of your time practicing sending code. It helps you
associate sound sequences with characters. Code oscillators are good for this.
You can also use your
You probably want this
adapter:http://www.radioshack.com/product/index.jsp?productId=12970495
But it is hard to tell without knowing what type of new computer you got.
Tom - wa4ta
From: w...@i29.net
Date: Mon, 5 May 2014 13:14:52 -0500
To: Elecraft@mailman.qth.net
Subject: [Elecraft] TIP,
Thanks for asking and answering this question. This was on my list of
things to figure out.
Tom - wa4ta
On Thu, Mar 27, 2014 at 3:53 PM, Joe Harris joseph.a.har...@gmail.comwrote:
Ed,
See page 20 of the K3 manual, in the Line Out setting. You can set the Line
Out level in Config, or it
I am in the same boat.
I added my gmail account since my wa4ta at hotmail account is not receiving
mail from QTH.net
I opened a ticket with Microsoft over a week ago. I have received a few
messages from the list since then but not many.
Tom
On Mon, Mar 24, 2014 at 8:48 AM, ejk...@gmail.com
I am surprised no-one mentioned this.
You can buy retention clips if you have issues with disconnects: Anderson part
# 110G68
They cost about 50 cents.
Can we drop this subject now? it has been re-hashed many times.
73 - Tom - wa4ta
Date: Thu, 13 Mar 2014 12:05:49 -0300
From:
I get this type of noise when my wife uses a laminator.
I also get a lot of sporadic noise in the morning around the time people get up
which I assume are hair driers and curling irons.
It really could be anything, but probably something one of your neighbors has.
Good luck finding it, if
: [Elecraft] K3 to KAT500
On 1/24/2014 3:52 PM, tom armour wrote:
If I buy a K3/100 without auto tuner and a KAT500 is there any additional
cable I need (other than coax) to connect the two together?
Some folks feel the need for an AUX cable to tell the KAT500 what band
it is on. I don't
Why do you need to know the loss of the tuner? Put a power meter after the
tuner and see what your rig is putting out.
Is this the type of chart you are looking
for?http://www.packetradio.com/pdfzips/SWRvsPowerNwatts.pdf
It is not really the tuner that is causing the loss. It is more the
If I buy a K3/100 without auto tuner and a KAT500 is there any additional cable
I need (other than coax) to connect the two together? or does KAT500 come with
all cable beeded to connect it to the K3? I see a cable for KAT500 to KPA500
but not to the K3.
Is there anything I'll be missing with
@mailman.qth.net
傳送日期︰ 2014年01月25日 (週六) 8:04 AM
主題︰ Re: [Elecraft] K3 to KAT500
On 1/24/2014 3:52 PM, tom armour wrote:
If I buy a K3/100 without auto tuner and a KAT500 is there any additional
cable I need (other than coax) to connect the two together?
Some folks feel the need
Get the one from Hobbyking for $24 instead of from Power Werx. It is the exact
same Turnigy 130A meter without the power
poles.http://hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=10080You
can buy a lot of power poles for $40.
73, Tom - wa4ta
Date: Wed, 16 Oct 2013 17:42:34 -0700
This comment made me do a search on Kraus.
I found one of his books online for free in the open source archive.org site
(this is the streaming link, they also have it in
PDF):http://archive.org/stream/Antennas2ndbyjohnD.Kraus1988/Kraus-Antennas-2nd.Edition-1988#page/n0/mode/2up
I though others
18 matches
Mail list logo