WTB the KXB30 board for the Elecraft KX1.
Please contact me at wb4...@cfl.rr.com
72,
Art
WB4MNK
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@m
New, unused, unbuilt KXB30 30 Meter Adapter for the KX-1
$20.00 plus postage.
Please contact off list.
73,
Bill - K6WLM
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr
Martin,
Yes, peak the trimmers on 30 meters - use a fully insulated tool (like a
ceramic or hard plastic screwdriver) for the most precise tuning. If
there is anything metallic on the screwdriver, your hand capacity will
have an effect while tuning. If you only have a metallic tool, wrap the
Hi, Don.
Well I finally did get around to checking out the KX1 with a signal generator.
Here are the signal levels at which I can barely distinguish a signal:
80m -126dBm
40m -130dBm
30m -107dBm
20m -120dBm
So, 30m does appear to have a problem.
I'll have to try re-tweaking the 30m trimmers, b
Martin,
I would be hesitant to make comparisons based on signals on the air.
The signal propagation can make a big difference.
If you have a signal generator that will produce a measurable (and
repeatable output, that can be used for a valid comparison.
Normally, the 30 meter signals are as
Hi,
I wonder if anyone else has an observation about the sensitivity of
the KX1 on 30m with the original 30m board compared to the 30 & 80m
board? I've noticed that signals are not as strong on 30m now with
the new board. For example, the RTTY station on 10100kHz is at best a
4x5 whereas it use
Paul,
Yes, put the pads in place just in case anything shifts later. You could
tape them in place, use rubber cement, a dab of 'Shoe-Goo' or any other glue
that is advertized to bond with both rubber and fiberglass. Most glues will
bond with the fiberglass, but few will stick to rubber. You onl
Hello everybody,
My KX1 construction is going well. The basic 20/40 rig is all done and I have
even had a couple of QSO’s on those bands. I am now working on the KXB30 option
and I am having a small problem with installing it on top of the main board.
I have flush-trimmed everything as close to
Assembled surplus KXB30 for the cost of postage. Email me off list.
73
Eric N0HHS
KX1 #670
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http:/
Hello
Just finished assembling KX1/KXAT1.
It works great for 7 and 14MHz.
Now looking for KXB30 module.
Is there anyone who have unused KXB30 (suppose you might
change KXB30 to KXB3080) and can give me the module with
reasonable price ?
Please give me a direct e-mail, Thanks
73 de aki, ja1nlx
I'm happy to report KX1 #959 is now sporting options KXB30 and KXAT1...and
all is working as one seamless unit!
I must admit that the dinky KXB30 is a deceiving little board! By the time
you route the wires down through the main KX1, you've earned your stripes on
this puppy. The detail work requ
11 matches
Mail list logo