Hi Igor,
Very good ideas!
Thanks
73
Frank
W3LPL
- Original Message -
From: "Igor Sokolov"
To: elecraft@mailman.qth.net
Sent: Friday, April 3, 2020 2:53:55 PM
Subject: Re: [Elecraft] Transceiver Test Bed at W3LPL
Frank, you can add different headphones on Radi
Frank, you can add different headphones on Radio#4 to the mix :)
Also on SSB try recordings of BY stations to make it more difficult.
73, Igor UA9CDC
31.03.2020 22:44, donov...@starpower.net пишет:
During the Coronavirus crisis many of us have much more time than
usual for serious technical
Thanks Bob
73
Frank
W3LPL
- Original Message -
From: "Bob Wilson, N6TV"
To: "Elecraft Reflector"
Cc: "Frank Donovan, W3LPL"
Sent: Thursday, April 2, 2020 9:20:13 PM
Subject: Re: [Elecraft] Transceiver Test Bed at W3LPL
On Tue, Mar 31, 202
On Tue, Mar 31, 2020 at 12:50 PM Barry wrote:
> I can't speak to the other radios, but you do need to fiddle the
> values of the AGC on the K3s to get the best out of the radios.
For review, my recommended K3 menu settings and knob position for maximum
reduction of receiver "mush" is docum
Hi Grant,
I'll do it right, you can take that to the bank
73
Frank
W3LPL
- Original Message -
From: "Grant Youngman"
To: donov...@starpower.net
Cc: "Elecraft Refl"
Sent: Tuesday, March 31, 2020 9:03:14 PM
Subject: Re: [Elecraft] Transceiver Test
If you’re going to do this, I trust it won’t be “anecdotal”, and that you have
the equipment necessary to provide concrete measurable and rmost importantly,
repeatable, results. Maybe you do. But anything else is just opinion.
Grant NQ5T
> On Mar 31, 2020, at 4:46 PM, donov...@starpower.net w
Hi Jim,
I'll try a variety of transceivers as QRM generators and document
the good and the bad...
tks
73
Frank
W3LPL
- Original Message -
From: "Jim Brown"
To: "Reflector Elecraft"
Sent: Tuesday, March 31, 2020 8:16:59 PM
Subject: Re: [Elecraft
My measurements of N6TA's FTDX5000 about three years ago found it to be
pretty clean on SSB. http://k9yc.com/FTDX5000_Report.pdf
73, Jim K9YC
On 3/31/2020 12:39 PM, donov...@starpower.net wrote:
I'll also use my FTdx5000s as QRM radios
Sent: Tuesday, March 31, 2020 7:49:50 PM
Subject: Re[2]: [Elecraft] Transceiver Test Bed at W3LPL
Frank,
I can't speak to the other radios, but you do need to fiddle the
values of the AGC on the K3s to get the best out of the radios. I think
the defaults are just to see if the radio works or
s is doing something worthwhile. ;-)
73,
Barry
K3NDM
-- Original Message --
From: donov...@starpower.net
To: elecraft@mailman.qth.net
Sent: 3/31/2020 3:39:44 PM
Subject: Re: [Elecraft] Transceiver Test Bed at W3LPL
Hi Jim,
Very good ideas! I'll also use my FTdx5000s as QRM radios and
a
2020 7:31:10 PM
Subject: Re: [Elecraft] Transceiver Test Bed at W3LPL
On 3/31/2020 10:44 AM, donov...@starpower.net wrote:
> I welcome constructive comments about my test bed, test procedures and
> results.
Hi Frank,
A worthwhile experiment. Suggestions. Use dirtier QRM rigs. Low cost
On 3/31/2020 10:44 AM, donov...@starpower.net wrote:
I welcome constructive comments about my test bed, test procedures and
results.
Hi Frank,
A worthwhile experiment. Suggestions. Use dirtier QRM rigs. Low cost
(less than FTDX5000) Yaesu rigs have lots of RF IMD on SSB, even when
not badly
I thought I was a master at making a BFD out of anything. I am not worthy!
Eric KE6US
On 3/31/2020 10:44 AM, donov...@starpower.net wrote:
During the Coronavirus crisis many of us have much more time than
usual for serious technical experimentation and testing.
I'm building a transceiver tes
During the Coronavirus crisis many of us have much more time than
usual for serious technical experimentation and testing.
I'm building a transceiver test bed and I'll regularly report the progress
of my test setup, procedures and results. The intent of my test bed
is to document the trans
14 matches
Mail list logo