Yes SWT25;
Rich
On 1/9/2016 7:50 AM, DGB wrote:
Is there a command for the RX ANT on the K3 ?
73 Dwight NS9I
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
On January 7, NR4C posted a function key message file for N1MM+ that
used KY commands to send FSK RTTY without requiring any FSK keying
interface connected to the K3/K3S AUX port. While the basic idea (<04>
used to terminate transmissions) is good, unfortunately there is an
error in this file.
Hi All
Is there any prospect of the KRC2 being updated to fully support the K3?
Ideally a new device with outputs covering all the HF bands, including the
new ones and the 6 transverter bands? I need this for a remote setup.
My old KRC2 has finally failed and no longer responds, but it never
Also note that a new field-test version of K3/K3S firmware is presently in test
(rev. 5.46) that corrects a long-standing problem with the "RX;" command. This
command is often used at the end of "KY;" packets, or just for general
use in returning the radio to receive mode. "RX;" now correctly
Is there a command for the RX ANT on the K3 ?
73 Dwight NS9I
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted
I have the same thing here, Bruce. Something in firmware was
changed a while ago and when I reported it to Wayne, he said
that it is within specs.
73, Ken K3IU
~~~
On 1/9/2016 11:09 AM, Bruce Meier wrote:
Today I noticed that the output power on
This has nothing to do with the new synth. We're hoping to have another
firmware release dealing with it soon. I've been working on other issues.
73,
Wayne
N6KR
On Jan 9, 2016, at 8:09 AM, "Bruce Meier" wrote:
> Today I noticed that the output power on 15 meters does
I noted a similar issue and found that increasing the power supply voltage a
bit returned full output. I think I have about 14.2v at the rig in receive
mode. This was before I updated the synths so I don't think it's related to
that.
Vic 4X6GP/K2VCO
> On 9 Jan 2016, at 6:09 PM, Bruce Meier
I suppose "spec" would be about 1 dB or so. If so, then somewhere
between 80 and 125 watts would be about right for a nominal 100 watt
radio. I, however, didn't see and published spec for transmitter power
in my K3S manual.
73
Bob, K4TAX
On 1/9/2016 10:27 AM, Ken K3IU wrote:
I have the
I have accidently purchased another KXPACBL. It is brand new still in the
shipping box as I received it from Elecraft. $39 and I will cover the
shipping.
Tnx
David
__
Elecraft mailing list
Home:
When using the cw messages in 0-9 memory will itwipe out the frequency memories
0-9 that you use recall tochoose?
73! Tomy KF7GC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Today I noticed that the output power on 15 meters does not reach 100w. The
max, according to the front panel meter reading, is 93w. So, I ran the
transmitter gain calibration and it did not help. I decreased the power to
90w and it reached 90w, so I gradually increased the power and it is fine
Mike
If your KRC2 failed, try to reload the firmware. Sometime, mine fails and
this is only the firmware to reload. I use with a K3 with no specific
problems.
73 Laurent F6DEX
-
Laurent F6DEX
--
View this message in context:
He had also published an article in QEX in 2014 about CESSB and said
that Flex is implementing it, and if improves the talk power by almost
3dB. I would love to see it in the KX3.
Gary Mitchelson
NC3Z/4 Pamlico County, NC FM15
On 09-Jan-16 19:10, David Anderson wrote:
> Having just read the
Tomy,
No, the CW memories and the frequency memories are recorded at different
addresses.
73,
Don W3FPR
On 1/9/2016 2:42 PM, Tomy Ivan via Elecraft wrote:
When using the cw messages in 0-9 memory will itwipe out the frequency memories
0-9 that you use recall tochoose?
Mint condition, K3/100 watts serial 8915 for sale, with the new syntetizer
Info algav...@gmail.com
73
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Having just read the article by Dave W9GR in Feb 2016 edition of QST magazine,
where he details Controlled Envelope SSB, I am keen to know if the existing
hardware in the KX3 and/or K3 could in the future support CESSB by a firmware
update?
At first I was worried that this technology may be
I haven't turned on the KRX3 second receiver in my K3 for over a year, so it
is time to sell it and its roofing filters.
The KRX3 also has its own general coverage receive option, which is also for
sale.
I am keeping the K3 itself, but may change some roofing filters.
I used the KRX3 with
Please understand: The buyer of the KRX3 will have the first to be able to
buy any or all of the other pieces. Once that deal is closed, any left-over
pieces will be available to others.
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Erik
Basilier
I just upgraded one of my rigs from a KXV3A to a KXV3B.
This KXV3A will accept the internal 2 meter option, K144XV.
Includes the KXV3A, rear panel plate, TMP cable assembly and mounting
screws. The manual is available on line.
$95 shipped priority mail to USA.
Rich - N5ZC
If there are any [Keysight Technologies] SystemVue users out there I had
implemented W9GR's CESSB algorithm after his first excellent article, and I'd
be happy to share the workspace with you.
Dave also made his MATLAB files available for download from the ARRL site after
his initial article,
I have 2pcs 1000Hz filters for sale. $80 each plus shipping or best offer.
Shipping worldwide,money via PayPal. Looking for 200Hz 5pole CW filter for the
2nd RX with offset as close aspossible to -0.9 (main RX filter has this
offset).Please contact me off list.
73 Jan OM2XW
22 matches
Mail list logo