Re: [Elecraft] OT: Fixing Slow Internet

Jim, OK that is reassuring. I will probably run it via cat5e cable and install my own RJ45 connectors so it can be custom length (and probably cheaper). My guess it will be better on crosstalk than commercially made ethernet cables. Answer to those who question my adversion to wireless:

Re: [Elecraft] K1 Filter Board Issue

Jeremy, Yes, an RF probe would be useful to evaluate the health of the crystal for 40 meters. Since those crystals are reliable, I suspect that you have a problem with the Pre-Mixer Bandpass Filter. You need to have at least 200mV peak to peak signal (70 mV measured with an RF Probe) to

Re: [Elecraft] OT: Fixing Slow Internet

Ed, I am also on DSL and have wired Ethernet throughout the house. Due to the long run to my house and the length of phone line in the house (entry to security system then back to the DSL modem - over 100 feet) the DSL/phone splitters did not work well, so the phone company installed a

[Elecraft] K1 Filter Board Issue

Hello, I recently finished the receiver portion of my K1 (40m/20m). I successfully aligned the 20m filters, but on 40m there is very little noise, and the noise does not change when there is an antenna connected. However, I have received some very nice signals on 20m. I have inspected the

Re: [Elecraft] Computer Keyboard and P3/SCGA

Actually you can have one bluetooth keyboard mate with 4 different devices at the touch of a button. Matias Wireless Aluminum Keyboard GL - Steve WB6RSE On Dec 8, 2016, at 6:31 PM, Guy Olinger K2AV wrote: You can only mate a

[Elecraft] FS: New-in-Box PR6 $65 shipped

Price revised to Black Friday level, hi! I have for sale a new-in-box (unused) PR6 6M preamp for the K3. I converted the transceiver over to the PR6/10/12 and this item is surplus to my needs. The PR6 E850347 6M preamp comes with two 31-218-RFX male-to-male BNC adapters, and the E85034B

Re: [Elecraft] Computer Keyboard and P3/SCGA

Hi Ed, You can only mate a device with one receiver, as you suspected. That is so that you can have two keyboards, mice in the same area, and have them unambiguously belong to two different PC's. Being able to do otherwise would kill that very common commercial usage, like close-by desks. That

[Elecraft] Computer Keyboard and P3/SCGA

Need help figuring out what may be an elementary problem with a computer and the P3/SVGA. Here's my objective: I would like to use a single wireless keyboard / mouse both to operate the text functions on the P3/SVGA, and to enter data into the computer itself. While operating I like to

Re: [Elecraft] KX3 power limit?

Thanks — now to see if I have that upgrade. Or, I will just take the time to upgrade everything. 73, phil, K7PEH > On Dec 8, 2016, at 12:43 PM, Walter Underwood wrote: > > The limit was raised to 15 W with firmware revision 2.38. > > POWER OUT NOW 15 WATTS MAX, 80-20

Re: [Elecraft] KX3 power limit?

The limit was raised to 15 W with firmware revision 2.38. POWER OUT NOW 15 WATTS MAX, 80-20 M: On 80-20 meters, the PWR control can now be set as high as 15 W (max is still 12 W on other bands). Supply voltage must be over 12.8 V on key-down as indicated by the KX3’s voltage display (tap DISP,

[Elecraft] Elecraft HQ phones are back up

As of 12:25 PM PDT (CA time) our phones are back on line. Early this morning there was an area wide power failure that caused problems both with our company phone connection and internet service. We apologize for the missed calls! 73, Eric /elecraft.com/

[Elecraft] KX3 power limit?

I am confused. Is the new 15 watt limit on output power a feature of new KX3 only or is it a software upgrade so that all KX3 rigs can be updated to 15 watts? __ Elecraft mailing list Home:

[Elecraft] KX3 as Controller for RemoteRig for K3?

I have a potential op for VY1AAA who would like to use a KX3 as a controller for RemoteRig. The last mention of this I can find on the web is below. Has their been any other work on this?Has the fast protocol been implemented, or is it beyond the capability of the KX3? 73, Gerry, W1VE

[Elecraft] FS: K3 - 100F Loaded

This is a very clean K3 - 100F 100 watt transceiver (S/N 45XX). I am the original owner, non-smoker. Features: Filters FM 13Khz, AM, 6 Khz, 2.8 Khz, 500 Hz, 400 Hz K144 2 meter module (totally gone through at Elecraft) KSYN3A synthesizer upgrade. All updates to current specifications with a

Re: [Elecraft] P3 and Centering the Display

Thanks for your note Dave! It is reassuring when someone else can confirm odd behavior and that it is not just me failing to understand what is supposed to happen. That is the case far too often as it is. :) Don't you just hate it when you have a brilliant idea and the hardware just won't

Re: [Elecraft] OT: Fixing Slow Internet

Indeed… why not use wireless? Turns out, my wireless connection (compared to wired ethernet) is -faster-! And, when I’m at my 4-land QTH, my only internet service is via an Xfinity hot spot, which I can purchase by the hour, day, week, or month, as needed. The only aspect about that service

[Elecraft] FS: New-in-Box PR6

I have for sale a new-in-box (unused) PR6 6M preamp for the K3. I converted the transceiver over to the PR6/10/12 and this item is surplus to my needs. The PR6 E850347 6M preamp comes with two 31-218-RFX male-to-male BNC adapters, and the E85034B power cable assembly. $95 shipped CONUS 73