The KX1 has been soldThanksTimNZ8J
Sent from my Galaxy Tab® A
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted
Good Evening,
I have been scanning the lower bands since mid-December. For the
last two weeks activity on 160 and 80 meters has slowed. I was hoping
for better. Upon checking SpaceWeather.com I find the sun is still
streaming ions our way; in fact there is a wind at the moment.
I
HiThe first thing I would do is to uninstall any drivers for serial ports you
have on your system using the device manager. In the process, you will see a
check box to delete the driver. Select this.Reboot. Next download the ftdi
drivers and do the install of the driver software. Then, plug in
I recently got my K3 back from the shop. In the interim I had other radios
to use. When I plugged the USB cables from both the KAT500 and K3 neither
were recognized by the computer running Win 7 and drivers would not install
after going through the usual process. The computer is acting like there
The rule of thumb is to over design the system. I have nearly the same system
with a few differences. I don't use a distribution panel, rather my 2x 140
AHr batteries and the solar panel are netted at the
K3 with a 5 Farad cap 12" from the K3. I monitor the voltage at the connector
of the
I have a KX1 for sale, it has the tuner and 80/30 meter board options, It looks
and works good. A minimum of 4 watts on all bands using 13.8 vdc. Comes with
the following:
Pelican 1060 micro case
Power cord with power pole connector
Laminated quick reference card
BNC to SO-239 adapter
BNC to
I find where the voltage drop is much like checking the drop across a
resistor in circuit. ie. use a volt-meter across each end of the
segment under test. (The volt-meter is parallel to the segment being
tested) It may be just a poor connection, or not.
Dick, n0ce
On 2/4/2017 6:17 PM,
I did some checking today on my voltage to the K3 using two different routes.
I am using an Astron RS-35m power supply. It was tuned up to output slightly
under 14v. Normally it mediates through a PG40s backup and switching device,
connected to three 140AH backup batteries as well as the
Thanks, Lyle, (and others).
I guess what I really want (and can currently afford) is an upgraded K3,
not a new K3S. I have an earlier s/n K3 (#1061), and have done some of
the mods, but not all of them. For example, I have the new synthesizer,
but not the upgraded DSP board, or even the
Chuck,
This link should answer your questions.
< http://www.elecraft.com/K3_K3S_Migration.htm >
73,
Lyle KK7P
On 2/4/17 1:20 PM, Chuck Guenther wrote:
I've read the Elecraft offer in the recent newsletter. Here is my
understanding of the migration service, which may be completely wrong:
I
I'm puzzled also I think you get both radios back, and if you want to
upgrade the older K3 (like to the new synthesizer board) if you buy the
board, they'll install it for the 199.99 flat fee.but I admit, it is
confusing
-Original Message-
From: Chuck Guenther
Sent:
I've read the Elecraft offer in the recent newsletter. Here is my
understanding of the migration service, which may be completely wrong:
I purchase a new K3S and pay $200.00 to have Elecraft install options
from my old K3 in the K3S, and I get back a new K3S (containing options
taken from my
In answer to the various emails I received regarding my post:
TX 0 0 7 7 13 15 13 8
RX 0 9 12 12 12 12 16 12
You must have the 6 kHz filter.
NOTE: I will not reply to individual emails asking questions. Post your
questions on the board - so that others may see also.
Bill W2BLC - K-Line
Nah, just keep saying the word 'sale'... that's in most females
vocabulary even if they don't grok ham radio. ;-) Then you can mention
you also saved by buying the kit form, which also keeps you out of her
hair for hours while building, using and researching for more. It's
winnable. Relate
On Sat, Feb 4, 2017 at 10:28 AM, wrote:
> Thanks; I didn't even know about the sale until you brought it up. You can
> always use the Wilma Flintstone method "charge it!" Now I need to try to
> figure out a way to explain this to the xyl.
> Alan Wong, KK6WA
>
I'm not sure
I have been using the K3 and KPA500 on AM lately and I have to say, it
has opened a whole new world to me - or returned me to a past world.
I made a set of AM settings in the EQ and am getting great audio reports
. The KPA500 develops enough power to keep me in the running 99% of the
time. No
Thanks; I didn't even know about the sale until you brought it up. You can
always use the Wilma Flintstone method "charge it!" Now I need to try to figure
out a way to explain this to the xyl.
Alan Wong, KK6WA
From: "Clay Autery"
To: "Elecraft Reflector"
17 matches
Mail list logo