Good Evening,
More birds are arriving and you can keep the windows open part of
the day. Spring has arrived and may just stay for a while.
Solar activity is low but one sunspot tried to grow. However, it is
decaying as I write. There is a hole in the corona through which a
stream
Mark...
All else aside, I'd suggest using good quality electrical tape, perhaps
even two layers. It won't slip and has a better half life than paper.
...robert
On 5/6/2018 02:58, Mark Petrovic wrote:
While performing the initial power on tests on my K2 S/N 7809, I noticed
that the VFO
While performing the initial power on tests on my K2 S/N 7809, I noticed
that the VFO knob/display tuning test produced a sluggish, intermittent, or
no change in display when I turned the knob in either direction.
I proceeded to remove the two chassis screws securing the control board to
the
Ooh, I'm immortalized in a Nabble archive. Preen, preen. :)
On Sat, May 5, 2018 at 21:13 Chris wrote:
> I had a similar problem. This thread may help:
>
>
> http://elecraft.365791.n2.nabble.com/KX2-quot-HI-CUR-quot-Warning-td7639589.html
>
> --Chris (KD2FLH)
>
>
> On
... I forgot to say that I can transmit and make QSOs with the rig even
with these high SWR so the power is getting to the antenna. The problem
(no power out) is present only during the tuning sequences.
...
__
Elecraft mailing list
I had a similar problem. This thread may help:
http://elecraft.365791.n2.nabble.com/KX2-quot-HI-CUR-quot-Warning-td7639589.html
--Chris (KD2FLH)
On May 5, 2018 8:52:34 PM EDT, VE2PID wrote:
>Hi to all .. I have a problem with my KX2 which appeared today. When I
>press
This often indicates the connection between the ATU and the BNC has opened.
73,
Lyle KK7P
Sent from my iPhone
> On May 5, 2018, at 5:52 PM, VE2PID wrote:
>
> Hi to all .. I have a problem with my KX2 which appeared today. When I press
> ATU to start a tuning sequence, I
Hi to all .. I have a problem with my KX2 which appeared today. When I
press ATU to start a tuning sequence, I hear the familiar relays noise
of the KXAT2. the 3 W power level is indicated, but it seems that no
power is getting out to the antenna or dummy load. After 2 or 3 seconds,
the
Device details at: http://pignology.net/pigknob/
Complete with the paperwork. I replaced it with a K-pod.
I ship to you in the lower 48 for $50. Check or money order - no PayPal.
Bill W2BLC K-Line
__
Elecraft mailing list
Home:
James,
Those errors and an explanation are in the chart near the end of the
manual. Those refer to attempting to transmit before doing several of
the calibration procedures.
The boards should have been pre-calibrated at the factory, but if yours
was pre-calibrated, the data has somehow
Hi folks,
I am new to Elecraft. I received my KX3 kit and built it yesterday. Was
very careful to follow all the directions and warnings. Now completed, the
receiver seems to work great, but having trouble with transmit.
In any mode, any band, any PTT request (key, mic PTT, etc), I instantly
While the Elecraft antenna tuners are excellent and wide range, don't be
surprised if you find wire lengths of antenna and counterpoise that they
will not get a match on for a given band. You may still find you have to
fine tune the lengths for them to work on all of your favorite bands, even
if
12 matches
Mail list logo