UNinstall the knobs CAREFULLY. Wash in warm water with Dawn dishwashing
liquid and perhaps a toothbrush if soaking doesn't work.
Use compressed air to make double sure they are dry before
re-installation. Be CAREFUL with the set screws...
__
Clay Autery, KY5G
(318)
Doug:
The remote and radio band data connectors are specialized connections.
They are for use with Ameritron supplied cables only. DB-DB15HE
I did see that the HV power supplies do have current limiting which
would imply there is some protection from excessive current based on
load
List comrades,
I am again stocked with K2 Fixed Audio Output Board kits as of
yesterday. If you placed an order in the last 10 days or so, it shipped
out this morning. You should see it is a few days.
Thanks for everyone's patience in waiting for more stock.
73,
Dave, W8FGU
On 1/15/2020
Hi, I need some help. I have a K3, the DB9 interface cable and an ALS (MFJ)1306
amplifier. I need to know if the amplifier handles power fold back for SWR by
itself or needs to connect to the K3. Question 2 is whether the cable allows
this. I know there is a setting in the K3 for external ALC
You missed some fun last year, the low was ~0F at K9CU's site in Urbana. During
setup it was in the upper teens with a 10 mph wind, which taught us just how
stiff the cold can make coax and fingers. My friend managed to get a dipole
into a tree but I settled for a small vertical clamped to the
Page 6 of KPOD Owner’s Manual says;
Macros are launched at the K-Pod using tap and hold presses of switches F1
through F8 just as you tap
and hold front panel switches on your K3S/K3:
- Holding switches F1 through F8 for 1/2 second or more launches K3S/K3 macros
1 through 8.
- Tapping
Hello,
Does your K2 need repair? Tuneup?
Want to sell it, but it needs some attention before offering it for sale?
In addition to tuning your rig, I can also rescue a building project you might
have started some time ago.
See what my clients have said about my construction and service work at
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
Elecraft's directions are usually very clear, but I am missing something
about encoding buttons on the K-POD.
I put my desired functions coding into the K3 Utility, but I don't see how
to apply them from the Utility to the radio where the function buttons on
the K3 imitate. What am I missing?
Thanks to both of you!
73, and thanks,
Dave (NK7Z)
https://www.nk7z.net
ARRL Volunteer Examiner
ARRL Technical Specialist
ARRL Asst. Director, NW Division, Technical Resources
On 1/24/20 7:28 AM, Don Wilhelm wrote:
Dave,
I would suggest removing the knobs and clean them with dish washing
Dave,
+1 on Don's suggestion. I usually use some warm water and a mild dish
soap and let the knobs soak for awhile. Then I use a soft toothbrush to
remove any crud. I have done a whole bunch of K1 & K2 knobs like this
and it always works pretty well.
73,
Dave, W8FGU
On 1/24/2020 10:28:32
Dave,
I would suggest removing the knobs and clean them with dish washing
liquid, water and an old toothbrush.
Dry fully before putting them back on the K3.
73,
Don W3FPR
On 1/24/2020 10:01 AM, Dave Cole wrote:
Any suggestions for the best cleaner for the old black screw locked knobs?
Any suggestions for the best cleaner for the old black screw locked knobs?
--
73, and thanks,
Dave (NK7Z)
https://www.nk7z.net
ARRL Volunteer Examiner
ARRL Technical Specialist
ARRL Asst. Director, NW Division, Technical Resources
__
Kev,
Sorry, but that will not work. The KPA100/KAT100 needs internal signals
from the K2. Those signals are not available from the KX3.
73,
Don W3FPR
On 1/23/2020 11:20 PM, Kev Schache wrote:
I'm confined to operating from home due to age restraints but I'm also
the very proud
... and here in Franklin, western NC we'll be using our ancient K3 with
mild temps
73 Dwight NS9I
On 1/24/2020 12:54 AM, Jim Brown wrote:
On 1/23/2020 6:38 PM, Wayne Burdick wrote:
I'm embarrassed to report that we've lost our Winter here in the Bay
Area
As a refugee from Chicago, I can
Here in St Augustine, FL it will be in the 70’s and windy. The SAARS club will
be putting on winter FD at the EOC. Anyone close please drop in and join us.
Dave K8WPE
David J. Wilcox K8WPE’s iPad
> On Jan 24, 2020, at 12:56 AM, Jim Brown wrote:
>
> On 1/23/2020 6:38 PM, Wayne Burdick
But where does the USB plug into.
Sent from my iPhone
...nr4c. bill
> On Jan 24, 2020, at 1:31 AM, W0MU Mike Fatchett wrote:
>
> The keyer would be hooked into the keyer/paddle jack?
>
>> On 1/22/2020 3:04 AM, Nr4c wrote:
>> What to plug Winkeyer into at the radio end? The K4 is connected
17 matches
Mail list logo
