[Elecraft] K3 TXEQ

I am using a Heil Gold Line microphone with a HC4 a HC5 cartridge. Does anybody have TX EQ setting that they have used with these mic cartridges. I know that EQ needs to be tailored for one's actual voice. Bob WB8DDI __ Elecraft

[Elecraft] No Output Power on K3

I purchased my K3 when they first came out I remember that it would putout RF. I've been away from the hobby for a while I can't get any RF out. When in CW mode, when I key the radio, I hear a tone, the TX led does not come on I can adjust the power knob very the setting past 100 watts. There

[Elecraft] Recall: No Output Power on K3

Bob Wehking would like to recall the message, [Elecraft] No Output Power on K3.__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net

[Elecraft] K3 ALS 600

I have a K3, S/N 225 an ALS 600, S/N 12911 that I would like to interface. Do I need to connect the ALC to the amp. Anything else needed to get the two to play together? Bob WB8DDI __ Elecraft mailing list Home:

[Elecraft] K3 Questions

While I wait for my K3 to arrive, I need to make an RS232 cable from the K3 to my computer serial port. Does the K3 require the use of a null modem cable? I assume to control the K3 with Ham Radio Deluxe Logger32, data needs to be transmitted back forth between the rig the software program via

[Elecraft] K2 for sale

I have a K2, s/n 4998 that includes the following for sale: KPA100 - 100 watt amplifier KSB2- K2 SSB Option KDSP2 - Advanced K2 DSP Filter K160RX- K2 160M / 2nd RX Antenna Option FDIMP - Finger Dimple KAT100-2 -100W ATU with EC2 panels installed in EC2 below. EC2

[Elecraft] K2 Audio issue

I have a K2/100 an Icom 756Pro. I am trying to use a switch box to switch a Icom SP-21 8 ohm speaker between rigs. When I have the K2/100 connected to the SP-21 I have to turn the audio control way up to hear anything, but when I switch back to the Icom radio its audio output is OK. Is this

[Elecraft] 160RX issue

I added the 160M module to my K2 radio will not receive anything on this band. The VCO voltage reading are 2.45v at 1800 5.63v at 2000. Using the basic K2, I get 13 watts output on 160. Any ideas? Bob WB8DDI K2/100 # 4998 ___ Elecraft mailing list

[Elecraft] K2 Audio/Sensitivity Issue

About two months ago, I built a K2 - SN 4998 , KDSP, KSB2, KPA100 everything worked. Yesterday I built the KNB2 K160RX boards after installing them, my audio is very low except for strong SSB signals the sensitivity across all band appears to have decreased. When using the XG2 signal

Re: [Elecraft] K2 Audio/Sensitivity Issue

. - Original Message - From: Bob Wehking [EMAIL PROTECTED] To: Elecraft@mailman.qth.net Sent: Sunday, October 09, 2005 11:03 AM Subject: [Elecraft] K2 Audio/Sensitivity Issue About two months ago, I built a K2 - SN 4998 , KDSP, KSB2, KPA100 everything worked. Yesterday I built

Re: [Elecraft] K2 Audio/Sensitivity Issue

Things work better when you follow directions. I forgot to add the jumper where R89 once was installed. - Original Message - From: Bob Wehking [EMAIL PROTECTED] To: Bob Wehking [EMAIL PROTECTED]; Elecraft@mailman.qth.net Sent: Sunday, October 09, 2005 11:09 AM Subject: Re: [Elecraft

[Elecraft] K2/100 RS-232 Problem Logger 32

I completed the KPA100 everything works except I can't get the K2 to communicate with Logger32. I setup the radio for COM1, 4800 baud, 2 stop bits, no parity. Kenwood-all have toggled both DTR RTS on off. The cable is wired correctly based on the manual. I've checked all the solder joints

[Elecraft] KPA100 Fan Issue

I have progressed to page 46 when I go to the PA menu parameter, I see Off, on, F1.10 E, but never see the Fan nor. Does anyone have an idea what I am doing wrong or do I have a hardware problem? Bob WB8DDI K2 #4998 ___ Elecraft mailing list Post

Re: [Elecraft] KPA100 Fan Issue

Found my probelm...can't follow directions! - Original Message - From: Bob Wehking [EMAIL PROTECTED] To: Elecraft@mailman.qth.net Sent: Tuesday, September 20, 2005 1:40 PM Subject: [Elecraft] KPA100 Fan Issue I have progressed to page 46 when I go to the PA menu parameter, I see

[Elecraft] K2 Birdies

I have been tuning my receiver have determined that I have a few birdies in the 40M band, but there are more in the 20M band that are a S9 level. Frequencies are 14.212.22, 14.217, 14.264.8614.315 that all sound more like buzzing sound. Any ideas? Bob WB8DDI K2# 4998

[Elecraft] Re: K2 Birdies

I checked the birdies on my Icom 756Pro they are also there so it appears something in my office is causing them...time to start turning of my hubs, switches etc. - Original Message - From: wayne burdick [EMAIL PROTECTED] To: Bob Wehking [EMAIL PROTECTED] Cc: Elecraft

Re: [Elecraft] K2's 4 MHZ Master Oscillator.

After I followed Wayne's procedure, I did do the CAL PLL then CAL FIL for all the crystal filters. Bob WB8DDI - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: Earl W Cunningham [EMAIL PROTECTED]; [EMAIL PROTECTED]; Elecraft@mailman.qth.net Sent: Thursday, September 01,

[Elecraft] K2DSP Real time clock issue

I just completed the kit the DSP portion works great, but when I go to the real time clock, the display shows EE-EE-EE. I checked the voltage of the battery insured it was installed correctly. Any ideas? Bob WB8DDI K2# 4998 ___ Elecraft mailing list

Re: [Elecraft] K2DSP Real time clock issue

It helps to read follow the manual.dah Everything is Ok now with the clock Bob WB8DDI - Original Message - From: Bob Wehking [EMAIL PROTECTED] To: Elecraft@mailman.qth.net Sent: Friday, September 02, 2005 11:21 AM Subject: [Elecraft] K2DSP Real time clock issue I just

[Elecraft] Microphone question

I just finished completing my K2 # 4998 wonder what type of hand or mobile mic I should use? Bob WB8DDI ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub

[Elecraft] K2's 4 MHZ Master Oscillator.

I used Wayne Burdick's article to calibrate my K2. When I first tuned in WWV, the zero beat was at .5. I adjusted c22 measured TP1(VCO) TP2(BFO) until the two test points matched. Now WWV zero beats at 1.5 . Should I have set my dial to 1.00 then adjusted C22?. I have also

[Elecraft] K2 Power output Issue

I started to do the 40meter tx power test when I set the control for 2.0 watts, I get 2 watts out. When I set it for 5 watts, I get 5 watts but can get any higher no matter if I set the control to 10 or higher. I have the same issue on 80 meters. I haven't tried it on any other band. Bob

[Elecraft] VCO Alignment

I have a problem with the VCO voltage readings. When I tune L30 to read 6.00 v at 4000, I get the following: The second set of numbers is when the core of L30 is turned all the way down. Any ideas? 80M35002.12V 4.14V 40006.00V7.93V 40M70001.92V

[Elecraft] Solder Question

I just received my K2 today, serial# 4998. I was wondering if the Kester solder I have, 244-6337-8800 which is a 245 NO CLEAN FLUX CORE SOLDER, ALLOY-63/37, .031' can be used to build the k2? ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net