[Elecraft] XV 432 questions...

Hi guys, although the XVTR seems to operate quite ok there are some issues: Local Oscillator Level: Max is 3.3 volts with L3 near initial adjustment but L4 and L5 are about two turns each out of the body. Osc. restarts ok. is this ok? Keying for filter adjustment: When keying the rig

[Elecraft] XV432, Q1...

Hi List, I soldered faster than I read. So Q1 is now installed in a common fashion without teflon spacer. Leads are clipped. What am I going to do now? If the teflon is just for spacing I would remove the Q, prolong the leads and install it without the teflon but spaced (I think the teflon

[Elecraft] K2 receiver problem - AGC alignment, CAL S LO/HI

Hi list, hi all those who answered my first question. I had 4V at Pin5 U2. So I replaced R1 with a pot of 50k and set it to 3.65, 3.72 and 3.8V. It got better for sure. The difference between AGC on and off is in all cases noticable, but slightly. But I think it's significant, because... When I

[Elecraft] Re: K2 receiver problem - AGC alignment, CAL S LO/HI

should not be ok I'll let you now. Thanks so far for all the help! Gerhard - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: Gerhard Schwanz [EMAIL PROTECTED]; Elecraft@mailman.qth.net Cc: [EMAIL PROTECTED] Sent: Friday, November 11, 2005 12:37 PM Subject: RE: K2 receiver

[Elecraft] T1 and remote control - works just fine

. Keep on building! Gerhard Schwanz DH3FAW http://www.gs-personal.de ___ Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de

[Elecraft] Zu verkaufen: KNB1

Elecraft KNB1 Bausatz zu verkaufen, da doppelt bestellt... Inventur ok. 39EUR inkl. Versand in Deutschland. 73 Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Gesendet

[Elecraft] XV144 Overload test fails

! Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de

[Elecraft] K1 Problem with Power Out on 30/40m

/bridges What else can I do or check? What could be the problem? Thanks in advance! Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Gesendet von Yahoo! Mail - Jetzt mit 1GB

[Elecraft] Antenna problem / phenomenon

9.9. And what's most stunning, the KAT1 can't even reduce this 9.9... Any idea why and most important: what can I do? Thanks! Gerhard Schwanz DH3FAW http://www.gs-personal.de ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must

[Elecraft] K1, KAT1 and remote Tuner

mentioned in the manual. So my question is: Is there a way to use external tuners that need more than 0.1W, namely 2-3W with non-resonant antennas? And if so, how? 73 Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de

[Elecraft] K2 SSB problem

there is maybe a little problem. Sending a 1kHz audio signal the receiving station could hear the same signal at +1kHz and -1kHz with -20dB max. These signals should be at least -40dB, correct? Question. How do I fix this? Thanks! Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs

[Elecraft] K1 RIT Mod!!!

build time like the VFO range. Keep on building! Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr

[Elecraft] K1 RIT Mod???

Hi there, I want my RIT to be +/-600Hz like in the K2. C7 has to be changed, to be smaller, says the manual. But how much smaller? Any idea or do I have to try? Thanks Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de

[Elecraft] K1 C62 and/or C63 missing

it with a 82pF? Thanks Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de __ Gesendet von Yahoo! Mail - http://mail.yahoo.de Mit Yahoo! Suche finden Sie alles: http://suche.yahoo.de

[Elecraft] KPA100 Problem still exists, but some new measurements

has -0.4V. Any idea and testing procedures appreciated! Kind regards Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list

Re: [Elecraft] KPA100 Problem still exists, but some new measurements

. And thanks to all who helped!!! Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de - Original Message - From: Mike Harris [EMAIL PROTECTED] To: Gerhard Schwanz [EMAIL PROTECTED]; Sent: Friday, February 04, 2005 5:14 PM Subject: Re: [Elecraft] KPA100 Problem still

[Elecraft] KPA100 voltage measurements AGAIN

? Kind regards and keep on building... Gerhard DH3FAW Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info

[Elecraft] Bad KPA100 PCB?

this problem too? What can I do? 73 Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub

[Elecraft] Bad joints on KPA100 again - with photo...

Hi again, just took a photo. You see it seems to affect only a special kind of hole (see picture). You can see on the picture that other holes work well. http://www.gs-roboter.de/problem.htm Iron is temp regulated at 330 deg C. Same like before. I already changed iron and solder. To no

Re: [Elecraft] Bad KPA100 PCB?

: I read the part with the needed iron but I understood the high power is needed for power transistor installation and such... And since everything else worked the way I did it before... Thank you very much! Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de

[Elecraft] KAT100 Question and a word for packing...

they always contained everything they should! Often more. 73 Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info

[Elecraft] Scan Problem

Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net

[Elecraft] K2 - no TX power problem

information? What else could I check? Thanks for any advice in advance! Gerhard Schwanz DH3FAW mailto:[EMAIL PROTECTED] http://www.gs-personal.de ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net http://mailman.qth.net/mailman/listinfo/elecraft You