Re: [Elecraft] T1 cable for the IC-705

Me too. I’m fine with folks running QRP transceivers off 500W amps and all, but I use them at <10W, so the T1 is perfect. Other options take up too much space/weight in my backpack! Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

[Elecraft] FS – KX2 Loaded Bundle $1000

FS – KX2 Loaded Bundle This was my travel QRP radio kit – but I’m not traveling! It is fully functional and in excellent condition. Price: $1000 (PayPal, includes free shipping CONUS) Bret/N4SRN KX2 80-10 M Transceiver KXIO2 Real-Time Clock KXAT2 Internal, Wide-Range 20-W ATU KXPD2 KXPD2

[Elecraft] K3S RF/SQL Adjustment

I'll admit I just don't know how best to adjust my K3S RK/SQL knob. I have AGC-S on, filters wide open at 2.8, and have set: AGC DCY nor AGC HLD 0.00 AGC PLS nor AGC SLP 012 AGC THR 008 AGC-F 120 AGC-S 020 On 14MHz CW Mode, where I see/hear CW no signal on my P3, with RF/SQL rotated full

Re: [Elecraft] K3S auto spot question

Follow-up to this old thread: When I set my filters 200-500Hz, with CWT on, and tune to strong signal, I can touch SPOT and see the frequency jump a bit. On my P3, I don't see the vertical green line jump to the peak of the signal. How is that? Bret/N4SRN -- Sent from:

Re: [Elecraft] K3S CW Optimization

Thanks Rick! -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list

[Elecraft] K3S CW Optimization

Apologies, as I'm sure this has been addressed before. I'm new to CW, just finishing CWOPS Beginner, and am looking to set up my K3S/P3 for best use on CW. Might there be a guide that I can start with? My K3S has filters down to 500Hz. Thanks for the help! Bret/N4SRN -- Sent from:

Re: [Elecraft] KX2 and Icom LC-192 Backpack?

Good point! I'll have a look at one and see if ICOM had good advice from SOTA'ers and a good pack partner to assemble such a beast. BRET/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

[Elecraft] KX2 and Icom LC-192 Backpack?

Has anyone looked at the ICOM LC-192 backpack for compatibility with the KX2? The KX2 is smaller than the IC-705. It seems, with the extra space, cable routing could work even if connectors are in different locations. Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

[Elecraft] K3S - Set Mode Across All Bands?

If I want to apply CW Mode and configuration settings across all bands, rather than each band individually, is there a way to do that? BRET/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

[Elecraft] FS - LP-PAN 2 with K3 Crystal

FS - LP PAN 2 with K3 crystal SN 02964 Excellent condition, no scratches or dents. ASUS XONAR U7 included. $100 shipped CONUS. Contact off-list Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list

Re: [Elecraft] Question on K3S and Winlink Express

Any luck with that Bob? I've been using Winlink on Packet VHF from a Kenwood TM-D710G but wanted to try 80m with my K3S. I'm to the point where Ardop is trying to connect to a local gateway about 5mi away from a 43ft vertical with remote ATU at base at 50W. No connection yet... I'm able to RX/TX

Re: [Elecraft] K3S/P3/KPS500/KAT500 Restart Woes

I think that's it! Thanks Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] K3S/P3/KPS500/KAT500 Restart Woes

Our downstairs, including my shack, was being remodeled and I just put my system back together. The good news: 1. K3S runs and I can RX FT8 on WSJT-X 2.1.2 - CAT works fine 2. Remote ATU works when I hit TUNE on the K3S - SWR read goes to 1.0 (I have a Directional Coupler/Panadapter TX Sensor

Re: [Elecraft] AXE1

I ran mine with a WSPRlite on 40m at 200mW with 2 counterpoise for a day, then added a 3rd counterpoise with no improvement observed. Spots out to 2400km from 300ft elevation. Mount was atop a 4ft tripod with counterpoise arrayed on grass. Bret/N4SRN -- Sent from:

Re: [Elecraft] AXE1 40m Extension

I’m finding it very useful to use a miniVNA to arrange 2 counterpoise wires for 20m for low SWR *before* engaging the ATU on my KX2. A random toss of wires might yield SWR > 9 and better arrangement < 2 SWR. I’ll try the same for 40m but may have trouble getting those wires to fit inside a hotel

Re: [Elecraft] AXE1 40m Extension

I see note to attach the radials to the transceiver near the antenna jack. If using a short coax to mount the antenna on THE Elecraft tripod base, is connecting radials to that base preferred or is connecting them to the transceiver still advised? I use the Elecraft AX1 radial and a separate

[Elecraft] AXE1 40m Extension

https://elecraft.com/products/axe1_40-meter-antenna-extender?mc_cid=19e05c5b30_eid=f94cda7417 Ordered mine already! BRET/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

Re: [Elecraft] Portable Speakers

Looks like a very nice and versatile tiny speaker for HAM portable as well as telecoms, music while traveling. BRET/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

Re: [Elecraft] AX1 Loaded Whip Antenna - Elevation and

I brought along a NanoVNA this trip and used it to array the two counterpoise attached to my AX1 antenna - adjustments of counterpoise brought SWR down from 9+ to <2. SNRs in the low ‘teens with a 200mW WSPRlite vs upper 20s - *inside* a hotel room with sealed windows. As Wayne said, the AX1 is

[Elecraft] AX1 Antenna Suction Cup Window Mount

I picked up an 8-pack of these suction cup window candle holders from Amazon for $7.99 https://www.amazon.com/Holiday-Joy-Strongest-Christmas-Celebration/dp/B01G6ED64K/ref=pd_lpo_sbs_201_t_0?_encoding=UTF8=1=8QNVHSVD55PT9X9D610K Three fit on the base tube of the AX1 antenna, clamp it tightly

[Elecraft] [KX2] WSJT-X Split - Rig or Fake It?

I'm using a KX2/KXPA100 at 40W on a Win10 laptop with WSJT-X 2.1.0 for FT8. Antenna is a G5RV at 40ft with base ATU 150ft away. I've been advised elsewhere that "Fake It" is a better choice than "Rig" for Split Mode: "it depends on what filter the radio has. Most are 2.4Khz (300-2700). If so you

Re: [Elecraft] Dedicated FTx Rig

http://crkits.com/ D4D DSB and a Raspberry Pi 4B maybe? Just got mine to build. Might need a LP filter addition to keep it right. Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

Re: [Elecraft] KX2 TX "Sticks On" in FT8?

Hi Don, No metal on those USD Audio Adaptors, unfortunately. I tried some Audio Isolator Transformers but those just gave PTT ERR on my KX2. I see some USB and Ethernet Laptop Ground devices that the EMF-sensitive people seem to use - I don't know if they work at all.

Re: [Elecraft] KX2 TX "Sticks On" in FT8?

While I had quite a few Mix31 beads on antenna coax and the various other power, CAT and audio cables connecting my rig, it seems adding a few more helped. I think it was a ferrite bead on the special cable set that connects the KXPA100 and KX2 that did the trick. RF leaking in somehow! While my

Re: [Elecraft] KX2 TX "Sticks On" in FT8?

I've got 2 Mix31 ferrite beads with 4 winds each on my SOTAbeams Bandhopper 40/30/20 coax feed, another before the coax feeds the KXPA100 and another just before the KX2 - as well as ferrites on power cords and audio/CAT cables connecting the rig. If that's not enough - ouch! BRET/N4SRN --

[Elecraft] KX2 TX "Sticks On" in FT8?

While running FT8 on my KX2/KXPA100, the TX red LED will sometimes stay on and the FT8 waterfall shows blank (like when TXing). ALC is stuck on 1 Bar when I've got it set 4-5 Bars. If I click Tune in WSJT-X once or twice I see the 4-5 Bars ALC and then all returns to normal. Is TX being "Stuck

Re: [Elecraft] AX1 Loaded Whip Antenna - Elevation and Counterpoise?

It comes to mind I have an Elecraft T1 ATU I might try attaching directly to the base of the AX1 rather than relying on the KX2 ATU 25-40ft from the antenna. I try to operate closer but sometimes have to run that RG58 to clear obstructions. Thoughts? Bret/N4SRN -- Sent from:

Re: [Elecraft] AX1 Loaded Whip Antenna - Elevation and Counterpoise?

Thank you Joe! I shall look forward to reading your article soon. Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] AX1 Loaded Whip Antenna - Elevation and Counterpoise?

I've got my little 20m AX1 and 3 tuned counterpoise wires on a 4ft tripod with wires extending to plastic chairs 3ft off the ground too. If I got that whip up to 2m above ground with sloping wires, would I gain much? Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

Re: [Elecraft] KX2/KXPA100 WSJT-X Setup?

That did it Don, thanks! -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net

Re: [Elecraft] Fan for KXPA100

Wow - yeah! Running FT8 30W my KXPA100 is psuging 55C and dropped to 35C with a 3" USB fan placed on top of the fins. When the shack gets cold this Winter, I may take the fan off again ;-) Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

[Elecraft] KX2/KXPA100 WSJT-X Setup?

I’ve got my KX2 working with WSJT-X FT8 and am just inserting a KXPA100/KXAT100 into the system. WSJT-X seems unhappy with CAT control - the KXUSB cable used to connect my PC to the ACC jack on KX2 but that’s now occupied by the KXPACBL/KX2ACBL cable combination that runs from the KXPA100 Control

Re: [Elecraft] Elecraft Website - Ordering Error 27JUL?

Tried again and works now - either fixed or a glitch. Order incoming... -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] Elecraft Website - Ordering Error 27JUL?

I'm trying to place an order on the Elecraft website noon EDT 27JUL. When I try to add an item to the cart the wheel just spins and spins. No-go on a Win10 PC or iPad. Might want to check that before Monday office open. Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

[Elecraft] KX2/AX1 WSPR vs FT8

I'm running my KX2 on 5W with a AX1 vertical loaded whip on 20m with two counterpoise cut for 1/4 wave. I'm able to RX/TX WSPR with my spots heard in minus single digits - some positive single digits. I'm also able to RX FT8 but unable to QSO - nobody apparently hears me on HamSpots. It seems I

Re: [Elecraft] T1 ATU for 200mW WSPRlite

Thanks Bill, but I wasn't clear the options I was looking for were how to use he T1 with the EndFed antenna I have with the WSPRlite, given that the T1 requires 0.5W and the WSPRlite outputs only 0.2W. Odd as it sounds, I'm looking for an "amplifier" to switch in to bump 10-25 fold to 2-5W as the

[Elecraft] T1 ATU for 200mW WSPRlite

I'm planning to do some camping and will bring along a KX3Helper EndFed 40-6m antenna with 9:1 Unan, T1 ATU and SOTAbeams WSPRlite to run on 30m from a USB battery bank. The T1 requires 0.5W to tune but the WSPRlite output is 0.2W. Any thoughts on options other than tuning up with another radio

Re: [Elecraft] AX1 Tripod Mount - Thread Dimensions?

Thanks! -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted

[Elecraft] AX1 Tripod Mount - Thread Dimensions?

My AX1 came with a nut embedded in the plate opposite of the BCN connectors. It seems the right place to add a knurled-head screw to affix the counterpoise(s) during use. I went to the hardware store and the clerk and I tried every screw that looked like it might fir but no-go. Does anyone know

Re: [Elecraft] [KX2] WSJT-X & Win10 Volume Mixer

I'll add that, with Win10 volume mixer sliders set at 50%, WSJT-X slider set to 50%, MIC GAIN is at 3-4 to get 4 bars with 5th flashing. Running Win10 volume mixer slider to 100% does not allow 4-5 bars on the KX2 TX even with MIC GAIN on 1 and WSJT-X slider near zero. BRET/N4SRN -- Sent from:

[Elecraft] [KX2] WSJT-X & Win10 Volume Mixer

I’m setting up WSJT-X 2.01 on a Win10 Surface Pro 6 laptop, using a Sabrent USB Sound card and GPS USB receiver to sync time. I’m running 5W indoors on a Elecraft AX1 antenna with supplied counterpoise on 20m. ALC flashes on TX between 4-5 bars with sliders on Windows sound at 50%, WSJT-X 50% and

Re: [Elecraft] FS: Box of 10 ARRL Handbooks 1953-1986

Only feeds those eHAM post replies to now say:”You should read the ARRL Handbook from 1953 forward before asking such questions on the forum.” That, and get a EE degree too. These newbies - sheesh! ;-) Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

Re: [Elecraft] AX1 comments from the field, and an AXE1 update (40 m extender)

Anyone want to write up a “cheatsheet” for newbies who buy the AXE1 and KX2 for easy success? Remember, we’re all not EEs ;-) Maybe in a few months, anyway. Bret, N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft

[Elecraft] AX1 Order Page Up but Broken?

I got a Tuesday 9Oct 506am EST email with a private order link for the AX1 antenna http://www.elecraft.com/elecraft_prod_list.htm No mention of AX1 antenna on the page. Needs a fix? Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

[Elecraft] [K3S] WSJT-X MSK144

So I'm trying WSJT-X MSK144 first time on my K3S - running 150W into a PAR AO-50 vertical loop at 30ft in Southern NH. Settings Rx 1500, F Tol 200, T/R 15s on Fast Decode (older 8 core CPU won't do Deep). By doing it wrong my local HAMs have kindly let me know to TX Odd on East Coast. I also had

Re: [Elecraft] K3S Delta Freq LED and Split Mode in WSJT-X

Thanks for the explanation! Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] K3S Delta Freq LED and Split Mode in WSJT-X

I have WSJT-X 1.9.1 running in Split Mode - Rig. I see the boxed SPLIT indication on the right of my K3S display, and sometimes the delta Freq (triangle f) LED is illuminated and sometimes not. I'll admit I'm not sure what that's about and would appreciate some clarity. Thanks! Bret/N4SRN --

Re: [Elecraft] K3S & PC Win10 Soundcard

Hi Joe, Yes, MIC SEL = Line In and I'm in DATA A. ALC is 4 bars solid and 5th flashing on TX. Got you on 3) JTAlerts is set to Soundcard (0) Windows Default Sound Card I should clarify my statement on TX when the BT RXr is plugged into the from Headphone jack - when WSJT-X is set to TX Enable

Re: [Elecraft] K3S & PC Win10 Soundcard

Hi Joe, So my PC looks like this: SOUND CONTROL PANEL Playback Headphones (High Def AUdio Dev) - this is the new device that appears when I plug the BT TXr into the PC Headphones jack Default device (Green check mark) Recording Microphone (Logitech USB Headset) Default Device

[Elecraft] K3S & PC Win10 Soundcard

I have WSJT-X 1.9.1 running fine with my K3S and Win10 on my PC. I'd like to enable JTAlerts audio alerts using a TaoTronics TT-BA01 BT transmitter plugged into my PC headphone jack but it seems any soundcard choice from JTAlerts stops TX from my RIG. When I plug in the BT TXr I see a new

[Elecraft] 2m in K3S?

When I ordered my K3S I got the 2nd receiver, general coverage and message recorder cards. Does any option added preclude install of the 2m option? I’m thinking to try 2m WSPR and FT8, as limited as those may be - will these work with the 2m option added to the K3S? Bret/N4SRN -- Sent from:

Re: [Elecraft] P3TXMON PEP vs K3S/KPA500 PWR?

Hi Don, I checked and my K3S is set in DATA A mode. I'm running SPLIT as well. The WSJT-X cites "advantages" but I'm not too clear on what those are! Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing

Re: [Elecraft] P3TXMON PEP vs K3S/KPA500 PWR?

Yep - got that set with PC at ~30%, WSJT-X slider at ~60% and MIC (Line Gain) at 18 so 4 bars solid and 5th just flickers. The LEDs on the KPA500 remain steady, it's just the P3TXMON that seems to vary. Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

[Elecraft] P3TXMON PEP vs K3S/KPA500 PWR?

With K3S/KPA500 PWR knob set to 100W (out on KPA500) I'll see SWR 1.00 on the P3TXMON (rATU at the antenna base tuned) but the PEP displayed might vary markedly from WSJT-X FT8 15sec cycle to cycle of TX from 49W, 13W, 66W, 28W, ... What's going on? Bret/N4SRN -- Sent from:

Re: [Elecraft] KPA500 Sporadic Power Hi/Lo

I'll add I seem to have an all-or-none limit in adjusting my MIC Gain - it's 5 bars on none when runing TUNE from WSJT-X. Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

[Elecraft] KPA500 Sporadic Power Hi/Lo

Running my K3S with KPA500 to a Par OA-50 6m antenna with KAT500 and K3S ATU on bypass as the antenna is tuned to ~1.1 SWR. I'll be doing an FT8 QSO and power will read 100W on one TX and then a few watts next. If I budge the K3S knob up/down a hair, it will jump back to 100W. When a few watts, I

Re: [Elecraft] AX1

WOndering myself... Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

Re: [Elecraft] [KAT500] Remembered Antennas

https://www.ncdxf.org/pages/beacons.html All 18 seem to be going, but not strong with poor conditions. BRET/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

[Elecraft] [KAT500] Remembered Antennas

I’m using VE3NEA’s Faros NCDXF beacon software to monitor the 5 bands using my K3S on bypass with a KAT500 on bypass, as my two antennas have rATUs at the bases. When I set the KAT500 to ANT2 it keeps switching back to ANT1 so I figure it must be remembering a prior band/ANT setting. How do I make

Re: [Elecraft] [OT] Heil ProSet K2 with Kenwood TH-D72a HT?

Thanks Don - nope, no volts! I’ll be looking for other options. Can’t have too many headsets ;-) Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

[Elecraft] [OT] Heil ProSet K2 with Kenwood TH-D72a HT?

My Heil ProSet K2 headset works great with my K3S, of course. I just got a used kenwood TH-D72a HT for some satellite fun and wonder if the Heil headset will work with the HT? The TH-D72a lists: Microphone Impedance2 kΩ Audio Output (at 8 Ω, 10 % distortion) More than 300 mW (at 7.4 V) But I

Re: [Elecraft] K3S/P3-SVGA CW Decode - P3 Power Cycle

> the svga. > 73 Tom > > > > Sent from my Samsung Galaxy smartphone. > > ---- Original message > From: MaverickNH <cbjesse...@comcast.net> > Date: 2017-11-25 2:31 PM (GMT-05:00) > To: elecraft@mailman.qth.net >

[Elecraft] K3S/P3-SVGA CW Decode - P3 Power Cycle

I have always had problems using the K3 Utility to change configurations from another mode to CW, as I could see text decode on the K3S VFO B display area after a restore to my CW configuration but not on the P3-SVGA external display without a lot of fiddling. I see now that simply turning the P3

[Elecraft] Begali CW Machine & K3S Integration?

Perhaps it’s just a question of using an external keyer with a K3S, but how do I best connect a Begali CW Machine to a K3S for optimal function? I’m using paddles (Begali Signature) now but just got a straight key (Vizkey Camelback) to start with as well. Bret/N4SRN -- Sent from:

[Elecraft] "See" CW WPM on P3/SVGA?

I wondering if there's a way to configure my K3S/P3/SVGA to "see" WPM in CW? I'm a beginner and would like to find those slow QSOs at ~20wpm. CWOPS has a Tue/Fri/Sun 7.035-7.045 6-8pm local suggestion for CWA students/graduates, but it's hard to find... Some combination of K3S and P3 settings, or

[Elecraft] [K-Pod] Mapping Knob to K3(S) Power, RF Gain, AF Gain?

Can the K-Pod Knob be mapped to the little knobs on the K3(S)? One of my problems is reaching into that 6-small knob cluster w/o tweaking neighboring knobs. Clumsy hands! Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

Re: [Elecraft] Kx33 PSU for KX2?

Thanks Mark - I was thinking the KX2 rather than the K2 but perhaps the same applies? Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] KXPD2 - Iambic B

Just starting to use my KPXD2 paddles on my KX2. I have them set to Iambic B. The left paddle will give only dits if pressed and held any length of time. The right paddle when pressed will give either dahs or fits and dahs, depending on length of press. I can do a R or K by pressing the right

[Elecraft] Kx33 PSU for KX2?

Saw a post from Howe at ProAydio Engineering "...and we have supplied many Kx33 14V supplies to KX2 owners who want to use the rig at 10W power when AC power is available." I didn't want to take this out of context, but can the Kx33 PSU be used to safely power the KX2 from my 110V US wall outlet?

Re: [Elecraft] P3: Something I find handy

Very interesting! What information might this add to a K3S/P3 setup that has a remote ATU at antenna base? Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

Re: [Elecraft] [KAT500] Only ANT1

Yep - ANT1 was the only connection enabled in the Utility. It's a nice 2nd-hand unit and I didn't check that first! Thanks. Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

[Elecraft] [KAT500] Only ANT1

I have a K3S/KPA500/KAT500 setup configured with AUX cables in the Enhanced configuration. Two antennas are connected to ANT1 and ANT2. The ANT LED is Green on 1 and when the ANT button is pressed will not select the antenna connected to ANT2. I can connect each antenna to ANT1 and each works but

Re: [Elecraft] [KPA500] Star * before PWR on LCD

Ah, should have search for asterisk instead of * or star! Thanks, 73, Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] [KPA500] Star * before PWR on LCD

I'm sure I read it somewhere, but what does it mean when there is a * star pattern before the PWR in the LCD? Search didn't get me there in the manual or forum. Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __

Re: [Elecraft] Adjusting Audio Level for Digital Modes

That seemed to do the trick Don. Edging the WSJT-X Power Slider down to mid-scale and K3S MIC LINE IN to ~30 gave me the wiggle room to get the 5th bar flashing. In fact, flashing just a bit was less effective than flashing a lot, but still short of solid 5th bar ON. But I guess the 5th bar flash

Re: [Elecraft] Question for SP3 owners

I just treated myself to a pair of SP3s, and I find them very nice speakers. Easy to configure on my K3S and the position to L/R ends of the Elecraft row of P3/K3S/KPA500 give a good stereo effect. Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/

Re: [Elecraft] Adjusting Audio Level for Digital Modes

At present, I have my PC's USB Audio Codec Playback Level set at 35%, and am adjusting ALC with the MIC knob. With the WSTJ-X Tune ON, I'm slowly increasing MIC until the 3rd bar shows. Further increase jumps directly to the 5th bar, with no 4th bar appearing or flashing 5th bar. I could swear I

Re: [Elecraft] [KPA500] K3S/KPA500/KAT500 - Adjusting TX Power

Adjusting power still has me stymied. Oddly, once set and TXing WSJT-X FT8 15sec cycles, it creeps up from 180-200W on the KPA500 readout towards 270W. The P3TXMON reads lower but creeps up over 200W on successive TX cycles as well. I moved my components around as suggested so the TX feed is now

[Elecraft] [KPA500] K3S/KPA500/KAT500 - Adjusting TX Power

I'm learning about a new KPA500/KAT500 installed with my K3S. When I have the K3S power knob set, in this case, to show 420-440W peak-hold as read on the KPA500 LED screen, I see the KPA500 SWR showing 1-3 LEDs lit (it may stay at 1 LED or climb from 1 to 3 LEDs over 15sec TX, always below 1.5),

Re: [Elecraft] [OT] ToyNTP GPSDO SNTP Server: Unable to listen on Port 123

That TCPView is a nice app - it helped me confirm that the Win10 NTP client was indeed coming back from the dead - not showing in Task Manager Processes but listening on ntp Port 123. Ending Process with TCPView seems more effective. Bullet to the head for those Zombie Apps! Thanks guys!

[Elecraft] [OT] ToyNTP GPSDO SNTP Server: Unable to listen on Port 123

I'm using a GPSDO to set my PC Clock uisng ToyNTP http://www.dxatlas.com/ToyNtp/ It keep time +/- 50 microseconds, which works great for digital work like WSJT-X. I have Network Time Protocol disabled in Administrative Services and I run ToyNPT as Administrator. It has worked fine for a year.

Re: [Elecraft] KPA500/KAT500 & K3S 2nd Subreceiver Diversity

I thought that might be the case. I did see an old thread where an option was mentioned by Wayne to do that, but perhaps that never transpired. Thank you for the advice. -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft

[Elecraft] KPA500/KAT500 & K3S 2nd Subreceiver Diversity

I getting to setting up my my K3S/100 with internal ATU with a KPA500/KAT500. I presently have antennas on the K3S ANT1 & ANT2 and use the K3S 2nd subreceiver for diversity receive. Does that work with the antennas connected to KTA500? Bret/N4SRN -- Sent from:

Re: [Elecraft] Wattage Draw - K3S/100 vs KPA500/KAT500 - for UPS

Thanks all - I've got some good ideas to try! Bret/N4SRN -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] Wattage Draw - K3S/100 vs KPA500/KAT500 - for UPS

As mentioned in another thread, I'm running my shack on a UPS that is rated 1500va/900w. With my K3S/100 and other hardware plugged in on the same input the UPS often max's out at 900W at < 100W on the K3S. Typically, the baseline with K3S on RX is ~350W and it spikes over 900W with TX at 100W and

Re: [Elecraft] [P3] P3TXMon Wattage/SWR

I found a manual 4-way switch that should work nicely. Thanks Don. Bret/N4SRN -- View this message in context: http://elecraft.365791.n2.nabble.com/P3-P3TXMon-Wattage-SWR-tp7633727p7633801.html Sent from the Elecraft mailing list archive at Nabble.com.

Re: [Elecraft] [P3] P3TXMon Wattage/SWR

And while I'm at it, is there a way to put a P3TXMON on both ANT1 and ANT2? Bret/N4SRN -- View this message in context: http://elecraft.365791.n2.nabble.com/P3-P3TXMon-Wattage-SWR-tp7633727p7633797.html Sent from the Elecraft mailing list archive at Nabble.com.

Re: [Elecraft] [P3] P3TXMon Wattage/SWR

Yep - LOAD to Antenna. That's what I thought should be correct. So why I installed it backwards last August, I'll never know! I just reversed it. Numbers look spot on now. *And* I see the UPS I'm using appears to limit output if I exceed the power draw specification. I just installed the software

Re: [Elecraft] [P3] P3TXMon Wattage/SWR

Possible - which side should LOAD be connected...K3S or Antenna? Bret/N4SRN -- View this message in context: http://elecraft.365791.n2.nabble.com/P3-P3TXMon-Wattage-SWR-tp7633727p7633794.html Sent from the Elecraft mailing list archive at Nabble.com.

[Elecraft] [K3S] WSJT-X v1.80rc1 FT8 Even/Odd Noise Difference?

On my K3S/100 using WSJT-X set up as per http://tiny.cc/K3S-WSJT-X with v1.80rc1 on FT8 I adjust my RF knob to a 30dB noise level. I often see ~10dB difference between even/odd 15sec cycles with no visible difference in background noise on the waterfall. That is, at 28-32dB on even I might see

Re: [Elecraft] On sunspots, amplifiers, and transceivers: An overview of the K-Line

Yep. Elecraft is great for people who have less knowledge and less understanding as it take real effort to bust the hardware. But the same hardware and software can enable advanced users to get amazing results. The Company support is excellent, if you have to resort to it. But the Forum usually

[Elecraft] Remote ATU with KPA500/KAT500?

I have a used KPA500/KAT500 set arriving next week and plan to integrate into my shack which has a K3S/100 with Internal Tuner, and three antennas on 2 coax feed lines: 1. RG213 coax 1 runs to a 43ft Vertical with a D.C.-over-coax powered SG-235 remote ATU. I'm putting a MFJ-2910 80/160 Matching

Re: [Elecraft] [WTB] KPA500/KAT500

Got one - thanks to all who replied. Bret/N4SRN -- View this message in context: http://elecraft.365791.n2.nabble.com/WTB-KPA500-KAT500-tp7633688p7633752.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft

Re: [Elecraft] [P3] P3TXMon Wattage/SWR

Hi Don, My mistake - yes, the internal ATU option for K3S is installed. I'll try as you suggested and report back. Thanks! Bret/N4SRN -- View this message in context: http://elecraft.365791.n2.nabble.com/P3-P3TXMon-Wattage-SWR-tp7633727p7633732.html Sent from the Elecraft mailing list

[Elecraft] [P3] P3TXMon Wattage/SWR

K3S100/KAT100 rig with P3, P3SVGA and P3TXMON Directional Coupler 200W. When TX at 100W, on 80m for example, the PEP on the P3 shows 2.4W PEP on the 120W scale and SWR is full scale at 99.0. I have put a Bird43 at my antenna base and verified 64W just before the SG-235 remote ATU on my 43ft

[Elecraft] [WTB] KPA500/KAT500

WTB - KPA500/KAT500. Looking for current hardware versions, factory built, excellent condition, no repairs made/needed. Please contact me off-list cbjesseeNH (at) comcast (dot) net by 8/25/17. No replies after. Thanks. Bret/N4SRN (Bedford, NH USA) -- View this message in context:

[Elecraft] [K3s} VFO B Display Options

I seems I keep disabling my ability to display multiple types of information on rotation of VFO B on my K3S. I must be reading the manual wrong on how to enable as I can't seem to do it right. Help appreciated. Goes in my personal K3S FAQ index of things to remember that I forget! Bret/N4SRN

Re: [Elecraft] [K3S] K3S High SWR Shutdown on FT8?

That alarm turned out to be my USP - the sound was hard to track down as it's on the floor. The USP is a CyberPower CP1500PFCLCD which is giving an Overload alarm on typically the last TX of a QSO at 100W. The specs are Output 1500VA 900W. I'm curious why power consumption increases with each

Re: [Elecraft] K8RA P4 Key to K3S?

Thanks for the advice all! Bret/N4SRN -- View this message in context: http://elecraft.365791.n2.nabble.com/K8RA-P4-Key-to-K3S-tp7633304p764.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list

[Elecraft] K8RA P4 Key to K3S?

I'm signed up for CW Academy Sept-Oct and picked up a used K8RA P4 Key http://www.k8ra.com/product-p/p-4.htm It has three thumbscrew wire connectors on top at the back. How do I connect that to my K3S? Bret/N4SRN -- View this message in context:

  1   2   >