[Elecraft] Re: K1 no output on 20 - KFL1-4 problem?

enjoy working on it. Great work Elecraft. --- Mike KL7R [EMAIL PROTECTED] wrote: I contacted the fellow from Kodiak who said replacing the 22MHz xtal fixed his problem. I also heard from another ham who said that Elecraft received some bad 22MHz xtals from a vendor and many of them failed

[Elecraft] Re: K1 no output on 20 - KFL1-4 problem?

I get it replaced and if it fixed my problem. Mike KL7R --- Mike KL7R [EMAIL PROTECTED] wrote: I attached a cliplead to the antenna jack of my station receiver and dropped a loop of it inside of my K1. I could hear local oscillators at 40 meters15.003 30 meters17.997 20 meters

[Elecraft] K1 no output on 20 - KFL1-4 problem?

bands. What could cause this behavior? Signal is going through T1 on other bands. Could there be something drawing down the signal on 20 meters? I looked for shorts and didnt see any on the filter board. Mike KL7R

[Elecraft] Re: K1 no output on 20 - KFL1-4 problem?

Very interesting Greg, I can hear some signal on 20 but weak. Sounds like we have identical problems, I wonder what could have caused 20 to go out? The K1 was on the shelf for a couple of months and was working fine when I put it up. I dont think I did anything dumb to cause it to stop

[Elecraft] Re: K1 no output on 20 - KFL1-4 problem?

I attached a cliplead to the antenna jack of my station receiver and dropped a loop of it inside of my K1. I could hear local oscillators at 40 meters15.003 30 meters17.997 20 metersnothing heard at 22 mhz 17 meters26.048 so I pulled out the 22 mhz xtal from the KFL1-4 board

[Elecraft] KX1 Mod / EPS1 12V DC-DC converter - WORKS!

/en/ds/MAX1771EVKIT.pdf http://www.maxim-ic.com/quick_view2.cfm/qv_pk/1030 http://pdfserv.maxim-ic.com/en/ds/MAX1771.pdf Have Fun Mike KL7R __ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

[Elecraft] RE: Why is K2 so easy to send cw with?

itself too. Anyway. I think it is weighting that makes you feel like you are in the pocket (to coin a jazz phrase) when sending. I would love it if someone would tell me what the weighting is... Mike KL7R Yahoo! Sports

[Elecraft] k2 #03373 lives!

swapped the inductors back to the proper holes, all was FB. The original PLL XTAL didnt tune far enough but the one in the Temperature Compensated PLL Reference Rpgrade did. Now to build the addon modules... Mike KL7R Courage is being scared to death - but saddling up anyway. - John Wayne

[Elecraft] PLL Reference Oscillator out of spec

KOREA G0) I am using a shielded 10mh at L31) Rev B boards. Rev E manual The rig works on receive on 40 meters FB I dont have the K2 Temperature-Compensated PLL Reference Upgrade. How much does that Upgrade cost? Mike KL7R Was Ser #1938 (unbuilt - then upgraded to rev b boards) Now Ser #3373

[Elecraft] re:KX1 Hand capacitance effect

frequencies? Does the noise go away when you take the rig outside? Does it go away with a different counterpoise length? Mike KL7R When in danger, or in doubt, run in circles, scream and shout. -- Robert A. Heinlein __ Yahoo! Mail

[Elecraft] Can I use an SB530 for D10 on the RF board?

: Can I use the SB530 in D10? Its forward drop was something like .17 volts. Mike KL7R When in danger, or in doubt, run in circles, scream and shout. -- Robert A. Heinlein Yahoo! Mail Stay connected, organized, and protected. Take the tour: http

[Elecraft] kx1 keying weight

I love the sound of the weighting of the KX1. What is its weighting? I want to set my K12+ keyer to sound the same Mike KL7R http://kl7r.ham-radio.ch __ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http