[Elecraft] K-Keys software discontinued, any alternative available?
__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3: Erratic behavior of REV button
Hi Jeff, I experienced the same behavior. But after some investigation i found here it was a user error. Unfortunately the A-B (Split) button is just beside the REV Button. So when holding the wrong button because of my fat fingers the Split is gone and UP calls are generated ;-) Suggestion to ELECRAFT: in LOCK mode also lock A-B (Split) button - I normally run the pileup with locked VFO. If this would also lock the A-B (Split) button this problem cannot happen. Just turning off Split will need holding two buttons instead of one. But in pileup Split mode I do not need to go to the DX QRG. There are normally more than enough UP callers. 73 de Olaf - DK2LO -- NEU: FreePhone - kostenlos mobil telefonieren und surfen! Jetzt informieren: http://www.gmx.net/de/go/freephone __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] P3 Temperature Specs
Hi all, I experience the same problem. It needs some time before the P3 displays the right frequency. It is much worse when it is cold. Now in winter time before sunrise early in the morning it is pretty cold at my station, sometimes only 13 degrees Celsius. Then it needs several minutes. At 20 Celsius it needs around 1 minute. First the P3 shows 0.0 frequency. After some time it shows frequency 36.nnn and then after some time the qrg is ok but cursors are out of display. Then after reboot of the P3 everything is ok. It is definitely worse when it is cold. 73 de Olaf - DK2LO -- GMX DSL Doppel-Flat ab 19,99 Euro/mtl.! Jetzt mit gratis Handy-Flat! http://portal.gmx.net/de/go/dsl __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] P3 behavior with REV-button in use
I am searching the SPLIT pileup by pressing the REV-button and listening to the up frequency range by turning the same time the big VFO knob to find the listening QRG of the DX station. Unfortunately the P3 behaves the following way: 1. Center frequency display does not change but spectrum display jumps to the split QRG. I do not like the jump in the spectrum. 2. The VFO B cursor does not change. After releasing the REV-button I have to turn the VFO B knob slightly to see the right position of the VFO B cursor. Please try yourself and look if it is the same in your configuration. Is it possible to change configuration to get a better behavior, perhaps in a new firmware release? Thank you all for any suggestions and help! K3 # 2463 firmware 04.22 P3 # 570 firmware 00.41 73 de Olaf - DK2LO -- GMX DSL Doppel-Flat ab 19,99 euro;/mtl.! Jetzt auch mit gratis Notebook-Flat! http://portal.gmx.net/de/go/dsl __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
