I agree on this, that is if you have to change the settings of the NR.
For the AF filtering it's another case. After I set the AF filtering for
CW and SSB, it's a joy to use.
Another 2 cents...
73 Arie PA3A
-Oorspronkelijk bericht-
Van: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]
Thanks to all for the comments. (I am using a 2x 400Hz and 2x 250 Hz
Inrad combo in my MP for selectivity at this time, and a wiide
roofing filter)
The subject is very interesting to me since I expect my K3 sometime in
June.
How about this one for the K3:
2.7 standard
2.1 8-pole SSB
All,
Reading all info about the roofing filters...
Many opinions but I still miss a few things here to decide on which
roofing filters I'm going to buy.
I'm a guy who likes to see the figures. (In the Lord we trust, others
have to bring data...)
Here's an idea.
The following measurements for
Would not it be nice... if someone measured the IMD dynamic range of the
K3 with the interfering signals placed within the bandwidth of the first
IF (roofing) filter?
Or has that one already been published somewhere? Or is that impossible
to measure?
Arie PA3A
If we distort our SSB audio by compression etc, then let's hope that the
sideband filter will limit the bandwidth. (I don't know where the
compression or whatever is done in a K3).
But if the PA distorts the signal even more, there is no filter to limit
this within a few kHz.
So I think the IMD
Dave,
Listening 6 kHz wide is fine if you listen up to 3 kHz UP AND DOWN your
frequency. (So you might have a station on zero beat freq, who cares)
Being an ex R/O used to listening on 500 kHz, this was normal operation.
73
Arie PA3A
-
Why do you want a 6kHz bandwidth in CW?
Chris,
Many people like the 1.8. I have the 2.1 Inrad combo in my ol' MP.
Pretty narrow to my ears. And I can use the shift width controls to
decrease the bandwidth some more.
I ordered the 2.1 for my K3.
If I need to knock out something, I'm convinced that the DSP filtering
will make it so.
Guys,
I donot understand this discussion.
Someone asked for a delay longer than 20ms. It's not in the formware
(yet).
That's it.
73,
Arie PA3A
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
David,
I had a fl2100z for years and just sold it a few weeks ago to make room
for a K3.
As Don said, the input is fixed but there is another thing that gives
you the higher SWR: feedback form the tuned anode circuit. There is a
neutrodynisation capacitor for that. It is supposed to neutralize
I don't mind waiting.
When I ordered the K3, I knew that it was gonna take 5 months or so
until delivery.
In the mean time I use my other rigs (K2 and an 96 MP) with great joy,
and read a lot about the K3 on the reflector.
73
Arie PA3A
___
Elecraft
Giulio,
Yes, the ptt line of the mic is the same as the dot-paddle. This is one
of the design flaws in the K2.
Don Wilhelm made a beautiful mod for this, but it is not a simple one.
You can see it on his website.
Over to you Don.
Arie PA3A
-Oorspronkelijk bericht-
Van: [EMAIL
My choice:
Main RX: 2.7 / 2.1 / 500 / 200
Sub RX : 2.7 / 400
73
Arie PA3A
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Let's stop speculating.
Did anybody talk to the guy?
73,
Arie PA3A
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
That Elecraft is testing the filters now is a good thing!
I remember a post from Elecraft a few months ago, that said that I
should not use the 8.2M IF filters that were intended for Yaesu's FT1K
because the filters for the Elecraft K3 were specially selected to get
top performance.
The recent
CW-swing is related to music. Timing is so important.
Ella Fitzgerald and Frank Sinatra are still famous for their timing.
A 1-2-3-4 march has a steady beat. But have you ever heard the Saint
Louis Blues March?
Lots of examples...
73
Arie PA3A
___
unconditional single signal response if the PBT (or filters)
were adjusted so they provided a response on the image.
73,
... Joe, W4TV
-Original Message-
From: Arie Kleingeld PA3A [mailto:p...@xs4all.nl]
Sent: Saturday, September 19, 2009 6:31 PM
To: li...@subich.com
Subject: RE
Dick,
This could be the KIO2 cable inside the K2, running from the serial
connector to the control board.
If it sags down, this will cause that kind of hash because it is too
close to the receiver circuitry.
Keep this cable as close to the topcover as you can.
73
Arie PA3A
-Oorspronkelijk
All,
About the NR.
YES, the new algorithms really work! I can even dig out the weak CW sigs
better.
Now my question.
I use the first NR settings (1-1 to 4-4) in CW and the mixed ones for SSB.
Switching mode from ssb to cw and back again means switching NR setting
every time. I happen to switch
Any transceiver can be improved. But working on the K2 again...
Elecraft would have to make a business case first and then decide.
Anyway, my K2 is just fine as it is, and it's on duty for the next few weeks
as one of the transceivers in the TY1MS dx-pedition.
I already worked them with my K3
Ed,
I agree with you on this. The way you describe it, That's the way I always
do it (and done that for years with my MP),
It would be nice if, after pressing split, the vfo's would be on the same
freq and in same mode. This would be a nice short cut.
The purist might add that the CW split
Don't forget to hold the sub button so that the diversity mode kicks in.
73 Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens Franki ON5ZO
Verzonden: vrijdag 23 oktober 2009 17:04
Aan: elecraft@mailman.qth.net
During the last CQWW SSB we had my K3 aside with two 756 pro III's and an
FT2000 at PI4D.
All operators agreed that it was very easy to operate the K3 and that it was
not the most handsome of the three but nobody cared. All eyes were on the
N1MM screen and the hands on the keyboard.
Excellent
I've tried the L-mix-R this weekend. It is good step forward but still, I am
missing one setting. What I would really like, is this:
Ab - Ba
I am writing it like this because I would like the main RX to be normal
level in left ear (A) and reduced level in right ear (a), and Sub RX normal
level
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens PA3CW
Verzonden: dinsdag 10 november 2009 8:48
Aan: elecraft@mailman.qth.net
Onderwerp: [Elecraft] [K3] Magic CW box and PIC programming
Hi Dick,
You can 'PIC' just about
Ken,
SLP High number = flat output for strong and weak sigs. Just give it a try
and see for yourself.
PLS: always on, it suppresses the AGC reaction to short pulses.
Never turned it off here. A lot has been written about this subject.
See: www.sherweng.com, presentation about: DSP Radios - Not
It took UPS express 34 hrs to go from Elecraft to my home.
(Pretty quick I'd say)
The 'normal way' was about 10 days.
73
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens David Quental
Verzonden: zondag 13 december
Dick,
You are right about the s-meter of the FT1K. Under S8 it cannot be trusted.
That is a fact. When I measured this on my MP a signal drop op 3 s-points
resulted in going from s8 to s1 or so on the meter, so that's about the same
as you see with yours.
About the noise, I have done a
Let me throw in a penny please.
Just for comparison:
FT1kMP : all controls full gain (except AF of course), antenna connected.
Then disconnect antenna and listen: nearly no audio, only the receiver
noise.
K3: do the same. Difference is that when I disconnect the antenna, the noise
coming from
Maarten,
In the menu: NB Save.
Switch that to on. That will solve the problem.
73 Arie PA3A
Verzonden: zondag 20 december 2009 10:08
Aan: Eric
CC: py...@terra.com.br; elecraft@mailman.qth.net
Onderwerp: Re: [Elecraft] K3 noise blanker
I have power lines at approximately 150 meters from my
- Main and Sub Rx audiomix:
Leftchannel - 100% main and 50% sub and
Rightchannel - 100% sub and 50% main
- Bring Notch filter inside AGC-loop (or partly inside)
- P3 point and click to change freq with a usb-MOUSE
Thanks
73
Arie PA3A
Even if the sub and main rx are linked in diversity, VFO B can display
another freq. Is that what you are describing? It is OK.
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens Richard Thorpe
Verzonden: donderdag 24
Main RX: 2.7 2.1 400 and 200
Sub RX: 2.7 2.1 400
Use of the filters:
Normal operation SSB: 2.7 (this filter is much wider than 2.7 but that's no
problem in normal band conditions)
Contest operation SSB: 2.1 (this is needed when the band is crowded)
Normal operation CW: 2.1 ,
Martin,
About the 2.7 filters and matching.
I have two of those and they do not match. I set the offset between the two
and they are now both 50 Hz off or so :-) . No need to worry about this. In
SSB you cannot hear any difference. (It will be a problem with the low
bandwidths so if you plan
Well,
I wouldn't tailor anything with such cartridges.
The HC4 and 5 are carefully tailored already by Heil. That's one of the
reasons why people by them.
73 and HNY
Arie PA3A
-Oorspronkelijk bericht-
Onderwerp: [Elecraft] K3 TXEQ
I am using a Heil Gold Line microphone with a
Thanks Al!
73
Arie PA3A
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help
Since the audio of MAIN and SUB was mentioned in the DVR thread, a
sperate discussion.
The way the audio from MAIN and SUB comes to your ears has been
discussed before, but here's one.
How about this solution.
1. Suppose the audio is in the balance mode.
Sub-pot in the middle
All,
Building the KRX3 into a the black magic K3.
Video: http://www.youtube.com/watch?v=5EJL8SlJ_L8
73
Arie PA3A
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr.
Jeff,
I had the same. I cut the strip in two, lengthwise -- et presto - two
strips.
73
Arie PA3A
---
What I have instead is an envelope labeled as E980148,
which contains one foam strip.
Am I headed for a delay, or is only one pad required?
73, Jeff K8ND
Olivier,
This feature was recently implemented in the new firmware.
Download it and read the release notes.
It's all there!
73,
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens Olivier F5MZN
Verzonden: zaterdag 3
YES, Ian, YES!
I support your idea and when thinking of itanother one about the
Notch controls.
The situation now is, that when the manual notch is switched on, and the
notch freq is on the VFO B display, I cannot move the VFO A!!
I first have to tap the DISP button or the Notch again. In
Well,
Mike wrote: The auto notch takes them all out after a few
seconds thinking.
After a few seconds of thinking.the K3 notch takes the tones out.
That is also my experience.
Just for comparison: the auto notch of my old 1996 MP (wow DSP!! in
those days) is much faster than the one of
So we have 2.78 and yes I'm happy with the improvements of the software.
There are a few categories of software-updates:
1. bug fixes (nothing to cheer about, the bugs should not have been
there, way to go Elecraft how quick you fix those bugs)
2. nice to haves (indeed nice: my callsign
No PTT when tuning so it won't key the amp. Put it in the menu to switch
the PTT on or off?
Come on guys, why put this in the K3 or in any transceiver?
I really really don't understand why. If you are using an amp, set the
amp to standby. The K3 signal will go straight through. That's what it's
I agree on this.
The 2.1 will give you better audio if you need it. It will, as a roofing
filter, perform just as well in a heavy ssb contest as a 1.8 .
73
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens Ignacy
Wayne,
I hope that this is not high on your list.
With all respect to everyone, this does not really add something to the
performance of the K3.
In my list of ranking software releases:
1. bugfix
2. nice to have, can do without
3. improvement in essential performance / extending TX-RX
Ian,
Yes you are right. My apologies.
73
Arie PA3A
-Oorspronkelijk bericht-
Van: Ian Maude [mailto:i...@gb7mbc.net]
Verzonden: donderdag 5 februari 2009 23:50
Aan: Arie Kleingeld PA3A
CC: 'wayne burdick'; 'elecraft Reflector'
Onderwerp: Re: [Elecraft] firmware suggestion for k3
Arie
This is an interesting subject.
I've read several opinions on how the K3-AGC works here and MORE
important: how it behaves.
Can somebody from Elecraft shine a light on the AGC behaviour? I'm very
curious now.
73,
Arie PA3A
__
Thanks Larry,
These measurements explain a lot of what's happening.
73,
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens N8LP
Verzonden: dinsdag 24 februari 2009 3:41
Aan: elecraft@mailman.qth.net
Onderwerp: Re:
WOW!!!
Thank you, thank you, thank you.
Arie PA3A
-Oorspronkelijk bericht-
Onderwerp: [Elecraft] K3 Firmware rev. 3.03: SUB RX band
independence,new AGC features, multiple ATU settings per band, etc.
K3 beta-test firmware revision 3.03 (with DSP rev 2.10) is now
available. This is
Actually BCD goes from 0 to 9. As far as I remember BCD means Binary
Coded DECIMAL.
73
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens dw
Verzonden: donderdag 19 maart 2009 20:55
Aan: Elecraft_List
Onderwerp:
Bill,
Had the same thing once.
Reloaded the firmware and that solved the problem here.
73
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens KB1PXD
Verzonden: zondag 22 maart 2009 15:07
Aan: elecraft@mailman.qth.net
Yes, here it comes: The elecraft panadapter!
Arie PA3A
-Oorspronkelijk bericht-
We will not be releasing amps at Dayton this year. In addition to our
ongoing K3 work, have other fish to fry. :-)
73, Eric WA6HHQ
Elecraft
Loaded FW 3.06 yesterday. All OK except
This morning I cycled through the bands and found 6 meters missing.
I am sure that 6m is mapped in. Checked that with K3-EZ and in the
config.
What happens is this:
Cycle up through the different bands and after the 10m band comes 6m? No
band noise,
Dave,
6 m is mapped in . I double checked that,
I will try some older versions of the FW this morning.
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens Dave G4AON
Verzonden: zaterdag 4 april 2009 8:42
Aan:
I've made some progress, thanks to the tips I got to my direct mailbox.
Thanks.
I'll report back later this day.
73
Arie PA3A
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I have tried to adjust the audio of the K3 to my liking.
Hi side of spectrum: To get rid of the higher freq's I set the RX-eq 8
to minus 8dB.
Lo side of the spectrum: I tried out the RX-eq 1 and 2. Absolutely no
difference! Not even with the lo cut set to zero.
RX-eq 3 (200Hz) responded better.
I totally agree
73
Arie PA3A
-Oorspronkelijk bericht-
Onderwerp: Re: [Elecraft] K3: Audio Mixer
This is great Lyle. I hope it makes it into a release soon as a menu
option.
Thank you, Gary W7TEA
__
Elecraft mailing
Yes, indeed.
It would be perfect if this would come in the menu. I'll put that one at
close hand, say under the PF1 button.
Especially if some (50%?) audio would leak from left to right AND right
to left. Which probably will have to be switched off when operating in
diversity, due to phase
Bob,
Regarding your message on the topic of - k3 NR Audio level increase -
you mentioned the relation of S-meter and notch.
Yes,
I certainly would expect the notch to be inside the agc loop so that
when I notch a strong signal, the underlying weak signal would come up
(and the s-meter then
Two simple computer speakers (only a few bucks on a flee market) --
fine audio.
73, Arie PA3A
-Oorspronkelijk bericht-
Onderwerp: [Elecraft] What are you guys using for external speakers?
For loud stations and ragchews I don't use headphones. I'm currently
using my old Yaesu SP-8
Worked my K3 in the IARU contest this weekend (PA6HQ 20m cw).
Performed flawlessly except for
Yes the AGC, and in the following manner:
I am one of thse people who always use AGC slow in CW and in SSB.
(Please guys, spare me the comments that I have to ride the AGC, that is
not the issue
Firmware is latest beta.
Arie PA3A
-Oorspronkelijk bericht-
Van: guyk...@gmail.com [mailto:guyk...@gmail.com] Namens Guy Olinger
K2AV
Verzonden: maandag 13 juli 2009 3:17
Aan: Arie Kleingeld PA3A
CC: elecraft@mailman.qth.net
Onderwerp: Re: [Elecraft] AGC fast recover after a K3
For all who still hesitate to do mods in their K3, here's a video how
easy some mods can be.
This video shows the KSYN3 ALC mod.
http://www.youtube.com/watch?v=CFS8ZtCNJ0A
73,
Arie PA3A
__
Elecraft mailing list
Home:
Charles,
There's a setting in the menu to remember the NB settings.
Switch that on and the problem is solved.
73,
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens Charles Johnson
Verzonden: dinsdag 28 juli 2009
Did the mod last week.
I have the KRX3 and I feel that it was not in the way at all.
Nor did I have a problem with the cables.
The most uneasy part was getting the screws and washers in.
The way that worked for me was:
connect the cable(s) to the KSYN3-board;
take 2 crews and inside tooth
FS: Still packed and new: K3 500 Hz roofing filter.
(offset: -.75)
Shipping to EU is OK
Please contact me off-line if you're interested.
73
Arie PA3A
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Duane,
In my case I only use the K2 DSP AF filtering. That works all right.
The NR, no matter what settings I used, have never impressed me, nor
really helped improving signal quality.
73,
Arie PA3A
-Oorspronkelijk bericht-
Onderwerp: [Elecraft] K2: Your common usage of the DSP
Hey
Let me jump ont this wagon too.
(Having taught morsecode receiving and sending to radio-officers for 5
years)
I was taught the 'EU-way', key on the side of the table. So, I taught
that to my student also.
What i see and feel when I do it the 'US-way', elbow on the table, it
works fine as long as
- Mouse connection to the P3 to point in the P3-display and shoot, My
number one!
- Keyboard connection to P3 to type something -- K3 will send CW,
PSK31, RTTY, or what say you.
- Take out the computer: config the K3 through the P3 if mouse and
keyboard are connected.
- freq-entering via
Eric,
The low freq response is still there in 3.27 / 2.24.
The way I check this is the response of the RX EQ. There's a good
response if I change the EQ setting on 100Hz and 200Hz.
Love it.
73
Arie
PA3A
---
It will reappear in a future release. Just not as a bug in another
feature
Besides RX dynamic range there are a lot of things by which one can
compare a good transceiver.
I am sure that many people will love the ic7600. It has some very nice
features.
73,
Arie PA3A
-Oorspronkelijk bericht-
K3 still at top. 7600 rated #15 for dynamic range. Even an old
-Oorspronkelijk bericht-
Van: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Namens Alexandr Kobranov
Verzonden: maandag 21 juli 2008 11:04
CC: elecraft@mailman.qth.net
Onderwerp: [Elecraft] K3: band enable/disable option ?
Maybe we can talk about BAND ENABLE config option which can
During a WW contest there are many buttons I press and controls I touch.
I do not mind touching a band button an extra time to skip a band when
I'm changing bands.
This is realy the least of my problems...
73,
Arie PA3A
-Oorspronkelijk bericht-
Van: [EMAIL PROTECTED]
[mailto:[EMAIL
Jon,
Try zerobeating against a Russian time signal station (forgot the
callsign). Good working frequencies for calibration are 4996 and 9996.
Nice strong and steady signals.
GL 73
Arie PA3A
-Oorspronkelijk bericht-
Van: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Namens Jon K Hellan
K3 arrived today.
Took UPS express 34 hrs 14 mins from Aptos,CA to Barendrecht,NL.
(NL = Netherlands, Europe)
73,
Arie PA3A
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info
All,
Building the K3 was staight forward. No problems encountered.
Config was easy ( I read the manual during my holidays before I started
building this weekend).
One 100W PA to go... Will do that tomorrow or otherwise next Monday
evening or so. Now far too busy listening the CW contest.
How about a normal L-type network? Connect one side to the balanced
line, and the other side via a current balun to the 50 coax. The tuner
is 'RF-floating'. (You can run the coax through a toroid or use two
seperate wires to make the current balun.)
73,
Arie PA3a
All,
I''ve been playing with my K3 (#1255) for a week now and I'm getting the
feel of the controls. Everything is OK but I'm still working on the
settings of the NB and the NR.
Firmware 2.23 / 1.88
Now about NR.
I receive a S9 pulse from an electric fence. Getting rid of this was
easy with
One more addition:
NB off, AGC PLS set to nor.
Bandwidth set to 400 Hz (with 400Hz roofing filter).
The pulse is back (about S5)working the agc.
Pulse is suppressed again at bandwidth 550 Hz (yes 550Hz, not 450Hz) or
greater (roofing filter = 2.1k at BW 450 Hz - 2100Hz)
Arie
One more addition:
NB off, AGC PLS set to nor.
Bandwidth set to 400 Hz (with 400Hz roofing filter).
The pulse is back (about S5)working the agc.
Pulse is suppressed again at bandwidth 550 Hz (yes 550Hz, not 450Hz) or
greater (roofing filter = 2.1k at BW 450 Hz - 2100Hz)
Arie
Ken,
I built my K3 10 days ago. There is one so239 in the KPA3 bag. But
there's another one in another bag. I don't remember which one it was
packed in but I found it. You'll find it too.
73
Arie PA3A
-Oorspronkelijk bericht-
Van: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Namens
New video:
The making of... K3 #1255
A 7 minute impression of building a K3.
http://www.youtube.com/watch?v=PD8QNVkIirc
73,
Arie PA3A
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber
Sorry, right subject now...
New video:
The making of... K3 #1255
A 7 minute impression of building a K3.
http://www.youtube.com/watch?v=PD8QNVkIirc
73,
Arie PA3A
___
K3 mailing list
[EMAIL PROTECTED]
http://pi4cc.nl/cgi-bin/mailman/listinfo/k3
The 7600 looks absolutely fine.
Now, back to my K3.
73
Arie PA3A
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Brian,
I am planning to do so. I will publish the video of the KRX3 assembly...
As soon as the KRX3 arrives.
Expecting it within a few months. (Ordered it Feb 2008)
73,
Arie PA3A
-Oorspronkelijk bericht-
Van: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Namens alsopb
Verzonden:
Lyle,
I can understand why the beat effect can happen at certain frequencies.
I read the message about the rounding errors.
My question is: can you give an indication of how often this happens. Of
course it depends on freq and filter offset but still, can you give an
idication how bad it is.
(was subject KRX3 Questions)
Thanks Bill,
I think I have to restate the question for the group.
Just suppose that main and sub receivers have filters with different
off-sets. It is stated that in some cases a 1Hz beatnote occurs due to
rounding errors.
Question is:
How often does the 1 Hz
In my shack:
On my left hand: iambic B ,if possible with auto character space
(depending on keyer used K3, K2, deluxe keyer late 70's, super-keyer
late 90's, Winkey)
On my right side: vibroplex bug (only one).
In the middle a keyboard connected to N1MM and winkey for contesting
(but that does not
Maybe this has been discussed before...
Using the manual notch to dip a unwanted signal works great.
I would expect that the AGC would react to this notching by increasing
the gain of the rx again. It seems that this is not so.
Is the notchfilter just an AF notch filter and not a IF notch (DSP IF
Thanks Lyle,
That's the thing I was describing indeed.
Any plans of moving the notch upstream as if it were notching in IF
(like in a analog rx) ?
Arie PA3A
At present, the NOTCH filter, whether automatic or manual, is after the
AGC loop.
73,
Lyle KK7P
Have not seen any answer to this question yet.
Here it is again.
Just suppose that main and sub receivers have filters with different
off-sets. It is stated that in some cases a 1Hz beatnote occurs due to
rounding errors.
Question is:
How often does the 1 Hz beat 'note' occur?
Is it on almost
Lyle,
Is anybody at Elecraft AT PRESENT working on bringing the notch
upstream as if it were notching in IF (like in a analog rx) ?
73
Arie PA3A
Hello Arie!
Key phrase is at present :-)
73,
Lyle KK7P
___
I bought the K3 for its raw hamradio-transceiver performance.
73,
Arie
==
Hi,
is there any possibility to grab a digital audio out signal (e.g. a PCM
stream) out of the K3 ?
Backgound is to get a digital audio out signal to send it via VoIP e.g.
via
Sorry to come in this thread so late.
Missed it because of a holidays.
Jean-Francois,
I had the same thing about a year ago and had to replace the main
control processor and the sub processor on the ssb board.
They share the ptt line that is directly connected to mic - jack without
any
Sorry to come in this thread so late.
Missed it because of a holidays.
Jean-Francois,
I had the same thing about a year ago and had to replace the main
control processor and the sub processor on the ssb board.
They share the ptt line that is directly connected to mic - jack without
any
All,
I would like to share the following experience on the AGC settings of
the K3.
Situation at my QTH:
There is an electric fence nearby my home that gives a pulse type of
noise.
The K3 handled that pretty well with the AGC PLS setting to ON.
Switching the AGC PLS to OFF gave me a lot of
MORSE - SSB= about
SOS - Mayday= Distress Traffic
TTT - Securité = Safety Traffic
XXX - Pan Pan Pan = Urgent traffic
73
Arie PA3A
Ex PCOH, PJUB, PCOB, the rest I forgot. (all ship callsigns)
___
Elecraft mailing list
David,
You are correct, PAN PAN three times is the right phrase.
73
Arie PA3A
-Oorspronkelijk bericht-
Van: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Namens David Woolley (E.L)
Verzonden: zondag 28 september 2008 10:32
Aan: elecraft@mailman.qth.net
Onderwerp: Re: [Elecraft] QRRR
I had a few spare moments this weekend and took the CW-paddle for about
100 RTTY QSO's during the CQWW.
Boy, that was very easy and, most of all, FUN. Only had to change my
routine from 5nn a4 to 5nn 14 :-)
Using the CW memories made it even more easy. I think it must have been
a bit strange
Yes Bill,
I used the IM during paddling and using the memories.
If using the paddle, be sure to really send ..--
A bit too slow with the paddle and it sends IM. :-)
The high speed of the memories: good idea! Implented for next time.
73
Arie PA3A
1 - 100 of 373 matches
Mail list logo