Admittedly a neophyte in learning the ins and outs of writing macros so
forgive if this question has already been addressed.
I am trying to place macros in the P3 SVGA memories and have run into
the problem that appears the K3 response time for doing band changes is
preventing the ability to
I use a wireless keyboard made by TECKNET that works fine. You plug in
the wireless adapter to the USB port on the P3 or PX3 and your set.
https://www.amazon.com/gp/product/B00M75WPKO/ref=oh_aui_detailpage_o03_s00?ie=UTF8=1
Dave K5MWR
On 11/20/2016 11:23 AM, Dauer, Edward wrote:
Some time
As an example of how you can set up markers, span and center frequency.
#MKA1;#MFA+00014077000;#MKB1;#MFB+00014078000;#SPN50;#CTF+00014077750;
73,Dave K5MWR
On 12/7/2016 9:22 AM, Sean Logghe wrote:
I was wondering if anyone has come up with a macro that will (reliably) move
the P3 to a
Here is one example that includes both K3 and P3 commands to set up for
JT-65 on 40M.
BN03;FA7076000;MD6;DT0;PC030;BW0400;FT0;SB0;#MKA1;#MFA+7077000;#MKB1;#MFB+7078000;#SPN50;#CTF+7077750;
On 12/16/2016 10:05 AM, Cady, Fred wrote:
Some folks have observed that sometimes a
Irwin
I have found that a wireless keyboard works very well, just plug the
wireless dongle into the P3 and then you have something you can move around.
I use a TECKNET SKU:X315 that I found on Amazon and it works very well.
Dave K5MWR
On 12/16/2016 1:15 PM, Irwin Darack wrote:
Do not
Sean
Apologies as I did not read your full post when I sent the earlier response.
I too see the same type of response and need to execute an involved
macro multiple times in order to get it to fully function. Depends on
what frequency/band and mode I am starting with. I would like to have a
At one point in the macro command reference there was a statement that
VOX/PTT selection would be available through a direct macro command.
Currently all I am able to make work is the SWT or SWH type command
which is basically of no use since there is no way to know what the
current mode is.
Bill
Exactly the problem I have. I would be happy with either a SET VXn
command or the VOX state was mode dependent, SET VXn would be my preference.
I am using 5.7 also and VOX is constant not mode dependent.
Bob, if we are missing something in the config or menu settings that
does make
I am trying to use my P3 to evaluate signals from other hams here in my
community. While I know the K3s is excellent, I am not sure what to
expect out of the P3 in terms of phase noise or response under high
signal conditions. I can always pad to lower the signal but that will
not help with
.
If you want to show data more than 80 dB below the peak of the signal,
you can repeat the measurement with the reference level reduced by 20
dB. More than that and the P3 will overload.
73, Jim K9YC
On Mon,3/13/2017 6:03 PM, K5MWR via Elecraft wrote:
I am trying to use my P3 to evaluate
Don't know if anyone else has experienced this but this morning I get
this message from Norton that the P3utility program is a threat named
"Heur.AdvML.C" and that P3Utility.exe has been removed.
Don't know if the recent major upgrade of Windows had any effect or most
likely it is due to the
How integrated will the KPA-1500 be with the KX-3/KXPA-100 system?
Thanks
Dave K5MWR
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
I am about to pair up a Drake L7B with my K3s and just wanted to tap the
groups wisdom on any issues.
If you are running this combination would appreciate any advice from
your experience.
Thanks
Dave K5MWR
__
Elecraft mailing list
A technique that works well using a dummy load to adjust a tuner is to
set up a bridge configuration where the dummy load absorbs the power and
the tuner is used to balance the bridge. Once done the dummy load is
switched out and rig drives the tuner. Electric Radio use to sell a
bridge like
I would love to see this also
Dave K5MWR
On 10/26/2017 10:10 AM, Chuck Teague via Elecraft wrote:
Is there anything in the works to provide a macro editor for the P3 that allows
creation and editing of the 50 macros in the SVGA? That would be really helpful
and a vast improvement over the
I was pretty certain that shipments would start this week. I just left
on a 4 week ski trip so naturally Murphy prevails and shipments start
while away :).
Has anyone received a shipping verification email, as I undertood
Elecraft was going to contact each person to verify the order and make
I have been asked to post the following K3s for sale for a friend.
K3s Transceiver Casual User Package *Price $2500 including shipping &
insurance.*
Serial # 11862
LPA3A 100W Upgrade for K3S
E850323 – Standard 5 ppm Oscillator
KAT3A-F -ATU for K3/K3s, factory installed.
17 matches
Mail list logo