I also went with 3-ft cables for the PR6. I used a couple of these:
www.allelectronics.com/make-a-store/item/CBL-27/3-BNC-BNC-CABLE-RG-58/1.html
Phil - AD5X
__
Elecraft mailing list
Home:
Mark,
I have the PR6 and it works very well. I would -not- consider
hanging it off the back of the K3 via M-M BNC's. Mine's
connected via two 6 BNC cables.
73!
Ken Kopp - K0PP
__
Elecraft mailing list
Home:
Mike,
I just bought the PR6 and added it to my K3 last week. I just connected it to
the back using the bnc barrel connectors that came with it. Seems very secure,
but I would probably remove it when transporting the rig. Makes a huge
difference on receive.
Dave, N4QS
Sent via BlackBerry
Mike == Mike Markowski mike.ab...@gmail.com writes:
Mike I'd like to buy a PR6 and see in its manual a photo of it
Mike apparently hanging off
Mike the back of the K3. Would the torque be unhealthy for the K3
Mike connectors over
Mike time? I'm also concerned something
July 2012 17:47
To: Mike Markowski
Cc: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 PR6 preamp
Mike == Mike Markowski mike.ab...@gmail.com writes:
Mike I'd like to buy a PR6 and see in its manual a photo of it
Mike apparently hanging off
Mike the back of the K3. Would
Oh, yes! I used to have my PR6 installed directly to the rear panel with
the double male connectors. Since my station interconnect is pretty
complex and uses essentially every connector on the rear panel, every
time I needed to access something back there the preamp was extremely in
the way.
I haven't purchased a PR6...yet. I wonder if anyone has successfully
installed the preamp INSIDE the K3? It sure would be slick to do so.
On 7/9/2012 7:39 PM, Randy Farmer wrote:
Oh, yes! I used to have my PR6 installed directly to the rear panel with
the double male connectors. Since my
: [Elecraft] K3 PR6 preamp
I haven't purchased a PR6...yet. I wonder if anyone has successfully
installed the preamp INSIDE the K3? It sure would be slick to do so.
On 7/9/2012 7:39 PM, Randy Farmer wrote:
Oh, yes! I used to have my PR6 installed directly to the rear panel with
the double male
.
--
Message: 31
Date: Thu, 24 Jun 2010 13:15:30 -0700
From: Jim Brown j...@audiosystemsgroup.com
Subject: Re: [Elecraft] K3 PR6 preamp
To: elecraft@mailman.qth.net elecraft@mailman.qth.net
Message-ID: 20100624201535.eeeca58...@gw1.nlenet.net
Content-Type: text/plain; charset=us-ascii
On Thu, 24 Jun
On Thu, 24 Jun 2010 23:15:52 -0800, Edward R Cole wrote:
Then you state that you are not suggesting the ARR is better. Not
better than what?
The Elecraft 6M preamp
73, Jim K9YC
__
Elecraft mailing list
Home:
Ed
There's a more reliable way of doing this. Turn on the dBV measurement
facility on the K3 and turn off the agc, reduce rf gain a bit. Arrange for
50ohm resistor noise to indicate 0dB and then substitute the 6m antenna and
see the difference.
BTW the preamps won't be below a 290K source -
--
Message: 36
Date: Thu, 24 Jun 2010 11:38:45 +0100
From: Graham Kimbell \(G3TCT\) g3...@lineone.net
Subject: Re: [Elecraft] K3 PR6 preamp
To: Edward R Cole kl...@acsalaska.net, elecraft@mailman.qth.net
Message-ID: 004901cb1389$6e506180$0602a...@a
Content-Type: text/plain; charset=iso
On Thu, 24 Jun 2010 11:52:46 -0800, Edward R Cole wrote:
Running both preamps probably only raises the noise level and
does not improve receiver sensitivity in any significant
manner.
I suggest that you defer judgment on this until you're trying to
copy very weak signals during a band
What is the noise figure of the K3 on six meters?
On SSB bandwidth I barely hear a noise increase when I switch from a dummy
load to my antenna.
73 Tom
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
W8JI wrote:
What is the noise figure of the K3 on six meters?
The noise figure of the preamp itself is typically 0.5 dB.
http://www.elecraft.com/manual/PR6_Owners_Manual_Rev_A.pdf
--
View this message in context:
Date: Mon, 21 Jun 2010 20:05:00 -0600
From: Bill VanAlstyne W5WVO w5...@cybermesa.net
Subject: Re: [Elecraft] K3 PR6 preamp [was: Another Happy Customer]
To: elecraft@mailman.qth.net
Message-ID: e78a2106e87a4f55911f00382d8dd...@billhp9250
Content-Type: text/plain; format=flowed; charset=iso-8859-1
From: K5RC t...@k5rc.cc
I also added the GaAsFet 6M preamp to the station and it makes a HUGE
difference on Six.
It needs to be pointed out from time to time that whether the PR6 makes no
discernible difference or a HUGE difference depends on one critically
important variable: YOUR NOISE
17 matches
Mail list logo