Health Canada, under Safety Code 6 specifies magnetic field strength in A/m
.
Ralph Cameron
EMC Consultant and Suppression of Consumer Electronic Equipment
(After Sale)
- Original Message -
From: Mike Hopkins mhopk...@keytek.com
To: 'Rich Nute' ri...@sdd.hp.com
Cc: 'IEEE'
Hello, All:
I am trying to make a thorough comaparison
between ETS 300 385 and EN 300 385 because
our product was covered under ETS 300 385
but now is under EN 300 385.
Here are some EMC standards quoted by
ETS 300 385 and EN 300 385 respectively.
Radiated Immunity:
ETS 300 385 refers to ENV
CFR's are available at no charge at
http://www.access.gpo.gov/nara/cfr/cfr-table-search.html
-Original Message-
From: Dick Grobner dick.grob...@medgraph.com
To: 'emc-p...@ieee.org' emc-p...@ieee.org
List-Post: emc-pstc@listserv.ieee.org
Date: Friday, December 17, 1999 2:53 PM
Subject:
CFR Services available online via GPO Access at...
http://www.access.gpo.gov/nara/cfr/cfr-table-search.html
-Bob
-Original Message-
From: Dick Grobner [mailto:dick.grob...@medgraph.com]
Sent: Friday, December 17, 1999 10:09 AM
To: 'emc-p...@ieee.org'
Subject: CFR's
Does anyone out
Happy Holidays group,
In getting agency approval on our I.T.E. product, the safety ground terminal
has come into question.
When hard wiring a product, Para. 3.3.7 indicates that the conductor is to
be clamped between metal surfaces, and the terminal shall not damage the
conductor. This has been
Dick,
You can download CFRs at no charge from:
http://www.fcc.gov/oet/info/rules/
Mirko
-
This message is coming from the emc-pstc discussion list.
To cancel your subscription, send mail to majord...@ieee.org
with the single line: unsubscribe emc-pstc (without the
quotes). For help,
Dick,
Try
http://law.etext.org
Scott Lacey
-Original Message-
From: Dick Grobner [SMTP:dick.grob...@medgraph.com]
Sent: Friday, December 17, 1999 1:09 PM
To: 'emc-p...@ieee.org'
Subject: CFR's
Does anyone out there know if you can download Code of Federal Regulations
You can find them at
http://www.access.gpo.gov/nara/cfr/cfr-retrieve.html#page1
http://www.access.gpo.gov/nara/cfr/cfr-retrieve.html#page1
Richard Woods
--
From: Dick Grobner [SMTP:dick.grob...@medgraph.com]
Sent: Friday, December 17, 1999 1:09 PM
To:
Does anyone know where I can purchase 50 Ohm to 75 Ohm coaxial impedance
matching pads, with low loss that are fixtured for SMA to SMA, or APC 3.5mm
to APC 3.5mm connectors?
Jim
Dr. Jim Knightene-mail:
Hello Mike,
I believe test is to be done after unit cools to levels normal during the
Noemal Heating Test. My rationale is that ITE equipment which goes into
abnormal conditions is serviced immediately. The dielectric test is made to
ensure that the equipment after being serviced does not pose a
I haven't done a transformer abnormal/overload test in years but it used to
be common to have a hipot failure if done immediately after the load was
removed (first few seconds) while the transformer passed after cooling down
for a few minutes. CSA and UL always required that the test be done
11 matches
Mail list logo
