On 5/5/20 9:21 AM, Stuart Stevenson wrote:
Sounds to me like you are up and running but your encoder is counting in
reverse of the axis motion.
How large is your following error in the ini file?
The motor ran away from a different problem.
Linuxcnc is not getting input from encoders.
A new
Sounds to me like you are up and running but your encoder is counting in
reverse of the axis motion.
How large is your following error in the ini file?
Set your following error very high.
Set your axis max velocity very low.
Disable the drive enable, start the machine, check the screen to see
On 5/4/20 7:51 PM, Peter C. Wallace wrote:
On Mon, 4 May 2020, Ed wrote:
Date: Mon, 4 May 2020 19:41:11 -0500
From: Ed
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] I can't seem to copy an error message
On 5/4/20 5:0
On Tue, 5 May 2020 at 01:53, Peter C. Wallace wrote:
> Are you sure you have the correct firmware?
There was a pin-dump earlier in the thread.
It shows muxed encoders, so I am thinking not.
(Mesa card names are great google targets. "7i29man" had me straight there.)
--
atp
"A motorcycle is a
On Mon, 4 May 2020, Ed wrote:
Date: Mon, 4 May 2020 19:41:11 -0500
From: Ed
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] I can't seem to copy an error message
On 5/4/20 5:02 PM, andy pugh wrote:
On Mon, 4 May 202
On 5/4/20 5:02 PM, andy pugh wrote:
On Mon, 4 May 2020 at 20:18, Ed wrote:
After trying a couple more edits then did a global replace of 7i80HD
with 7i80 and it would start but had no inputs from the encoders and
would run away if the drives were energized.
Don't energise the drives until
On Mon, 4 May 2020 at 20:18, Ed wrote:
> After trying a couple more edits then did a global replace of 7i80HD
> with 7i80 and it would start but had no inputs from the encoders and
> would run away if the drives were energized.
Don't energise the drives until the encoders at least count.
You
On Mon, 4 May 2020 at 22:00, Gene Heskett wrote:
> I do not see any encoder A/B or index signals netted in the file below.
> Shouldn't there be?
Not with a Mesa card.
--
atp
"A motorcycle is a bicycle with a pandemonium attachment and is
designed for the especial use of mechanical geniuses,
On Monday 04 May 2020 15:15:54 Ed wrote:
> On 5/4/20 12:19 PM, andy pugh wrote:
> > On Mon, 4 May 2020 at 18:00, Ed wrote:
> >> Well, that worked! Enclosed is the message. Looks to my
> >> unpracticed eye to be a network error.
> >
> > No it's this.
> >
> >> ./3-axis.hal:9: parameter or pin
>
On 5/4/20 12:19 PM, andy pugh wrote:
On Mon, 4 May 2020 at 18:00, Ed wrote:
Well, that worked! Enclosed is the message. Looks to my unpracticed
eye to be a network error.
No it's this.
./3-axis.hal:9: parameter or pin 'hm2_7i80HD.0.pwmgen.pwm_frequency' not
found
Drop the "HD" from line
On Mon, 4 May 2020 at 18:00, Ed wrote:
> Well, that worked! Enclosed is the message. Looks to my unpracticed
> eye to be a network error.
No it's this.
> ./3-axis.hal:9: parameter or pin 'hm2_7i80HD.0.pwmgen.pwm_frequency' not
> found
Drop the "HD" from line 9 of your 3-axis.hal file.
--
On 5/3/20 12:11 PM, Peter C. Wallace wrote:
The easiest way I know to capture error messages (with the uspace
version of LinuxCNC you are running) is to start linuxcnc from the
command line. All error
messages will be logged on the console which _can_ be copy-pasted
Well, that worked!
Tried the keyboard shortcuts of Ctrl+C for Copy and Ctrl+V for paste? Or click
the center button (pushing down the scroll wheel should work) or both left and
right buttons simultaneously for paste. If all fails snap a picture of the
error message, or try Alt+PrtScr to take a screenshot of the
On Sun, 3 May 2020 at 18:14, Peter C. Wallace wrote:
> The easiest way I know to capture error messages (with the uspace version of
> LinuxCNC you are running) is to start linuxcnc from the command line. All
> error
> messages will be logged on the console which _can_ be copy-pasted
2.8 has a
On Sun, 3 May 2020, Ed wrote:
Date: Sun, 3 May 2020 11:53:33 -0500
From: Ed
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] I can't seem to copy an error message
On 5/3/20 11:13 AM, andy pugh wrote:
On Sun, 3 May 202
On 5/3/20 11:13 AM, andy pugh wrote:
On Sun, 3 May 2020 at 16:47, Ed wrote:
Select All selects OK but I cannot do a copy to paste
into a message here. Any suggestions?
Are you saying that Ctrl-C doesn't work?
Nope. Ctrl-c nothing, right click nothing.
A doc in Mousepad it all works
On Sun, 3 May 2020 at 16:47, Ed wrote:
>
> Select All selects OK but I cannot do a copy to paste
> into a message here. Any suggestions?
Are you saying that Ctrl-C doesn't work?
--
atp
"A motorcycle is a bicycle with a pandemonium attachment and is
designed for the especial use of mechanical
I am in the process of setting up a mill with a Mesa 7I80HD and am
getting errors. Trying to copy the message in the pop up box and cannot
seem to do it, Select All selects OK but I cannot do a copy to paste
into a message here. Any suggestions?
Ed.
18 matches
Mail list logo
