Re: [Emc-users] Spindle control panel breaks LinuxCNC?

On Thursday 16 June 2016 02:57:46 Danny Miller wrote: > I have an X200 VFD. M3,M5,S18000 work fine, from MDI or code. My > MPG's "spindle" button works. > > On the default panel, there's a "Spindle" button flanked with a CW/CCW > indicator. Clicking any of that doesn't make the spindle go, even

Re: [Emc-users] Spindle control panel breaks LinuxCNC?

very difficult without a crystal ball you'll need to post your complete config folder as an archive somewhere , not just snips . so we can mimick your installation . it could be you have the spindle enable reversed in hardware , hence it works but not from the gui . ( easily done ) use the hal

Re: [Emc-users] Spindle control panel breaks LinuxCNC?

On 16 June 2016 at 07:57, Danny Miller wrote: > My MPG's "spindle" button works. > > On the default panel, ... Clicking any of that doesn't make the spindle go, > > It's not JUST that. Once you click on any of that, the VFD *will never > run again* until power is cycled.

Re: [Emc-users] adaptive feed reverse run

I think it is here... feature/reverse-run-master2 sam On 06/16/2016 02:24 PM, Nicklas Karlsson wrote: > I am running linuxcnc 2.8.0 and use adaptive feed. It is however not possible > with negative values. It works all the way down ot zero motion but no > backwards. > > I know there is a

Re: [Emc-users] RTAI Kernels?

On a different tack, where does one find a Preempt-RT patched kernel for Jessie? - Original Message - From: "Sebastian Kuzminsky" To: "Enhanced Machine Controller (EMC)" Sent: Thursday, June 16, 2016 4:12:55 PM Subject: Re: [Emc-users]

Re: [Emc-users] adaptive feed reverse run

Found it will try to get into my source. On Thu, 16 Jun 2016 15:17:18 -0500 sam sokolik wrote: > I think it is here... > > feature/reverse-run-master2 > > sam > > On 06/16/2016 02:24 PM, Nicklas Karlsson wrote: > > I am running linuxcnc 2.8.0 and use adaptive feed.

Re: [Emc-users] RTAI Kernels?

On 06/16/2016 10:51 AM, Todd Zuercher wrote: > Looking at the RTAI site, I see there is now an 5.0-test2. Has > anyone given that a whirl to see if it helps? I looked at it a few weeks ago and was disappointed to see that -test2 removed support for the 3.16.7 kernel that I had targeted for

Re: [Emc-users] RTAI Kernels?

On 06/16/2016 02:22 PM, Todd Zuercher wrote: > On a different tack, where does one find a Preempt-RT patched kernel for > Jessie? That one comes from debian.org, not linuxcnc.org. The debian folks publish it only occasionally; when they do it's available in

[Emc-users] RTAI Kernels?

Has anyone here noticed that the current Linuxcnc Wheezy RTAI-PAE kernel doesn't recognize any memory beyond 2.5G? That inspired me to look at the one for Jessie, and while the PAE in it does seem to work fine, there are other problems, namely the latest Linuxcnc buildbot version is only

Re: [Emc-users] Spindle control panel breaks LinuxCNC?

It's modbus, sorry forgot to mention that. What baffles me is the Spindle buttons on the panel, AFAIK, just map to the same spindle-run in the HAL that M3 goes to. I remember looking at the HAL monitor on this weeks ago and IIRC it was "spindle run true, but spindle-isrunning false". The

Re: [Emc-users] RTAI Kernels?

On 06/16/2016 08:36 AM, Todd Zuercher wrote: > Has anyone here noticed that the current Linuxcnc Wheezy RTAI-PAE > kernel doesn't recognize any memory beyond 2.5G? That's my fault - I forgot to turn on PAE in the Wheezy RTAI kernel (despite its name implying it has PAE).

Re: [Emc-users] RTAI Kernels?

Looking at the RTAI site, I see there is now an 5.0-test2. Has anyone given that a whirl to see if it helps? - Original Message - From: "Sebastian Kuzminsky" To: "Enhanced Machine Controller (EMC)" Sent: Thursday, June 16, 2016

[Emc-users] adaptive feed reverse run

I am running linuxcnc 2.8.0 and use adaptive feed. It is however not possible with negative values. It works all the way down ot zero motion but no backwards. I know there is a negative feed rate branch but do anybody know where it is? Nicklas Karlsson

[Emc-users] Spindle control panel breaks LinuxCNC?

I have an X200 VFD. M3,M5,S18000 work fine, from MDI or code. My MPG's "spindle" button works. On the default panel, there's a "Spindle" button flanked with a CW/CCW indicator. Clicking any of that doesn't make the spindle go, even with "S" set to a valid RPM. It's not JUST that. Once you