nd the
> > microstep scale is ok
> >
> > I think if a bad connection was there, the motor could not move
> >
> >
> >
> >
> >> - Original Message -
> >> From: "Valerio Bellizzomi" <vale...@selnet.org>
> >> To: "
; >
> >
> >> - Original Message -
> >> From: "Valerio Bellizzomi" <vale...@selnet.org>
> >> To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net>
> >> Sent: Sunday, April 23, 2017 2:46:03 AM
> >> Sub
is ok
>
> I think if a bad connection was there, the motor could not move
>
>
>
>
>> - Original Message -
>> From: "Valerio Bellizzomi" <vale...@selnet.org>
>> To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.
Sunday, April 23, 2017 2:46:03 AM
> Subject: Re: [Emc-users] how to configure motors in pncconf?
>
> On Sat, 2017-04-22 at 10:24 +0200, Valerio Bellizzomi wrote:
> > On Fri, 2017-04-21 at 11:56 +0100, andy pugh wrote:
> > > On 21 April 2017 at 11:45, Valerio Bellizz
ler (EMC)" <emc-users@lists.sourceforge.net>
Sent: Sunday, April 23, 2017 2:46:03 AM
Subject: Re: [Emc-users] how to configure motors in pncconf?
On Sat, 2017-04-22 at 10:24 +0200, Valerio Bellizzomi wrote:
> On Fri, 2017-04-21 at 11:56 +0100, andy pugh wrote:
> > On 21 April 2017 at 11:4
On Sat, 2017-04-22 at 10:24 +0200, Valerio Bellizzomi wrote:
> On Fri, 2017-04-21 at 11:56 +0100, andy pugh wrote:
> > On 21 April 2017 at 11:45, Valerio Bellizzomi wrote:
> > > The X stepgen is show as 5 in the tab, and as
> > > hm2_5i25.0.stepgen.05.counts in the test
On Fri, 2017-04-21 at 11:56 +0100, andy pugh wrote:
> On 21 April 2017 at 11:45, Valerio Bellizzomi wrote:
> > The X stepgen is show as 5 in the tab, and as
> > hm2_5i25.0.stepgen.05.counts in the test window, and it is changing
> > while I press the movement button
>
> I
On Fri, 2017-04-21 at 12:53 +0100, andy pugh wrote:
> On 21 April 2017 at 12:43, Valerio Bellizzomi wrote:
>
> > the current parameters are, step on-time 3000, step space 3000, dir hold
> > 5000, dir setup 5000
> >
> > ok, that's a little step forward :-)
>
> It is rarely
On 21 April 2017 at 12:43, Valerio Bellizzomi wrote:
> the current parameters are, step on-time 3000, step space 3000, dir hold
> 5000, dir setup 5000
>
> ok, that's a little step forward :-)
It is rarely necessary to make the step and space lengths as short as
possible, you
On Fri, 2017-04-21 at 13:43 +0200, Valerio Bellizzomi wrote:
> On Fri, 2017-04-21 at 11:56 +0100, andy pugh wrote:
> > On 21 April 2017 at 11:45, Valerio Bellizzomi wrote:
> > > The X stepgen is show as 5 in the tab, and as
> > > hm2_5i25.0.stepgen.05.counts in the test
On Fri, 2017-04-21 at 11:56 +0100, andy pugh wrote:
> On 21 April 2017 at 11:45, Valerio Bellizzomi wrote:
> > The X stepgen is show as 5 in the tab, and as
> > hm2_5i25.0.stepgen.05.counts in the test window, and it is changing
> > while I press the movement button
>
> I
On 21 April 2017 at 11:45, Valerio Bellizzomi wrote:
> The X stepgen is show as 5 in the tab, and as
> hm2_5i25.0.stepgen.05.counts in the test window, and it is changing
> while I press the movement button
I think this is the problem.
On Fri, 2017-04-21 at 11:03 +0100, andy pugh wrote:
> On 21 April 2017 at 10:36, Valerio Bellizzomi wrote:
>
> >
> > it is locked, that means current is flowing through the windings.
>
> Indeed, and also means that the drive is probably ready to move, but
> not seeing
On 21 April 2017 at 10:36, Valerio Bellizzomi wrote:
>
> it is locked, that means current is flowing through the windings.
Indeed, and also means that the drive is probably ready to move, but
not seeing step-pulses.
With the test window open, open a terminal and type
On Fri, 2017-04-21 at 09:57 +0100, andy pugh wrote:
> On 21 April 2017 at 09:23, Valerio Bellizzomi wrote:
> > Hello,
> > I am trying to configure motors in pncconf with 7i76 board,
> > I have selected the tab 'connector 2' and then selected a X-Axis StepGen
> > which shows a
On 21 April 2017 at 09:23, Valerio Bellizzomi wrote:
> Hello,
> I am trying to configure motors in pncconf with 7i76 board,
> I have selected the tab 'connector 2' and then selected a X-Axis StepGen
> which shows a StepGen-A and DirGen-B, but testing the motor with the
> panel
Hello,
I am trying to configure motors in pncconf with 7i76 board,
I have selected the tab 'connector 2' and then selected a X-Axis StepGen
which shows a StepGen-A and DirGen-B, but testing the motor with the
panel it doesn'tg move. is this the right thing to do?
Thanks
17 matches
Mail list logo