[flashrom] Re: Flashrom & Serprog Question
Please try out the latest flashrom version, maybe with a Linux LiveCD - it has more parameters which should be all accessible after reading about them at -help. On Sun, Feb 28, 2021 at 8:13 PM wrote: > > Hello again. Posted this question in irc, but had to disconnect, thats why i > ask here. I build Urja Rannikko's atmega644 programmer and used it with > flashrom 0.9.9 on windows. If i do not connect a flash chip (only parallel > flash chips here to test) to the programmer i get the messages that bus mode > parallel and spi are on (lpc and hw off). When i connect a SST39VF040 to the > programmer and execute flashrom the parallel mode is changed to off, so only > spi is on. > Can i force the programmer / flashrom to check only for flash chips in > parallel mode (with a parameter e.g.)? > > I did notice, that i had the wrong jumper position set for the flash chip (5V > instead of 3,3V). Is it possible that this is the reason why flashrom > switches to spi? I'm pretty sure that the flash chip is dead now, but i have > two more of this type :). > > Hope someone can help. > ___ > flashrom mailing list -- flashrom@flashrom.org > To unsubscribe send an email to flashrom-le...@flashrom.org -- Best regards, Mike Banon Open Source Community Manager of 3mdeb - https://3mdeb.com/ ___ flashrom mailing list -- flashrom@flashrom.org To unsubscribe send an email to flashrom-le...@flashrom.org
[flashrom] Re: About bios flash
BV should also work fine. Please could you describe your flashing setup, length of wires etc. On Sun, Feb 28, 2021 at 10:41 PM Aurelijus Gogas wrote: > > Hallow, > Thanks for your work (flashrom). In hardware list there is w25q32, but mine > is BV. Flashrom can not detect my chip. Is it not supported or i am doing > something wrong? I wired like example in tutorial. I have arduino mega2560. > What i can do? > Thanks for help. > > With Best Regards > Aurimas > > Get BlueMail for Android > ___ > flashrom mailing list -- flashrom@flashrom.org > To unsubscribe send an email to flashrom-le...@flashrom.org -- Best regards, Mike Banon Open Source Community Manager of 3mdeb - https://3mdeb.com/ ___ flashrom mailing list -- flashrom@flashrom.org To unsubscribe send an email to flashrom-le...@flashrom.org
[flashrom] Re: error bios
Well, it looks like your flashing has failed. Why? Maybe your flashing setup wasn't reliable enough: long wires etc. Until we'll learn more of it, we can't help you On Fri, Feb 26, 2021 at 10:55 PM edvaldo silva via flashrom wrote: > > Found GigaDevice flash chip "GD25Q64(B)" (8192 kB, SPI) on ch341a_spi. > Reading old flash chip contents... done. > Erasing and writing flash chip... Erase/write done. > Verifying flash... FAILED at 0x4500! Expected=0x45, Found=0xff, failed > byte count from 0x-0x007f: 0x156b2 > Your flash chip is in an unknown state. > > Att, > > Edvaldo Silva > edvaldo.si...@zohomail.com > +55 12 9 8209 6114 > > > > ___ > flashrom mailing list -- flashrom@flashrom.org > To unsubscribe send an email to flashrom-le...@flashrom.org -- Best regards, Mike Banon Open Source Community Manager of 3mdeb - https://3mdeb.com/ ___ flashrom mailing list -- flashrom@flashrom.org To unsubscribe send an email to flashrom-le...@flashrom.org
[flashrom] Re: Verifying flash failed
There's no way to know you've successfully wrote the chip until the verification - which failed in your case. As usual, please make sure that your wires are short enough etc. - your flashing setup should be reliable On Wed, Feb 17, 2021 at 5:17 PM Nathaniel King wrote: > > Hi, > > I have successfully erased and write the chip but it cannot verify it. When I > try to boot it it doesn't even boot, fan spin on for a second and then off. > > I am flashing my t440p. > > I hope I have given you enough information. > > Thanks, > Nathaniel > ___ > flashrom mailing list -- flashrom@flashrom.org > To unsubscribe send an email to flashrom-le...@flashrom.org -- Best regards, Mike Banon Open Source Community Manager of 3mdeb - https://3mdeb.com/ ___ flashrom mailing list -- flashrom@flashrom.org To unsubscribe send an email to flashrom-le...@flashrom.org
[flashrom] Re: Error on Yuna
It seems the write command failed since the start, so doing a reboot should be safe. On Mon, Feb 15, 2021 at 3:04 PM Flynn Price wrote: > > Hi, can you please see the error below? Am i safe to reboot? > Previously it said the flash was in an unknown state and to not reboot. > Thanks! > > Erasing and writing flash chip... 0x42-0x427fff: EInvalid OPCODE 0x06, > will not execute. > spi_write_cmd failed during command execution at address 0x42 > ERASE_FAILED > FAILED! > Uh oh. Erase/write failed. Checking if anything changed. > Reading current flash chip contents... 00-0x7f:R done. > Good, writing to the flash chip apparently didn't do anything. > This means we have to add special support for your board, programmer or flash > chip. Please report this on IRC at chat.freenode.net (channel #flashrom) or > mail flashrom@flashrom.org, thanks! > ___ > flashrom mailing list -- flashrom@flashrom.org > To unsubscribe send an email to flashrom-le...@flashrom.org -- Best regards, Mike Banon Open Source Community Manager of 3mdeb - https://3mdeb.com/ ___ flashrom mailing list -- flashrom@flashrom.org To unsubscribe send an email to flashrom-le...@flashrom.org