Dear All,
Can anyone advise me whether they have experienced the following problems, and
if so how to get over them?
1) Not getting 100W out on all bands - in fact as the band increases the
ability of the Flex to tune deteriorates.
2) TVI and RFI into the UHF and VHF bands.
Kind Rgds,
Gwyn
Hi All,
I have bought several transceivers Flex5000 for russian ham from the first
running and at present.
And I want to say, all transceiver made before April of the month had and have
problems SSB TX Audio.
New Flex5000 made after April, without problems, have clean and clear sound TX.
My
I can't seem to load the N8BV Vcom drivers on a new HP VISTA? machine? It looks
like it loads, when you go to Device Manager on the computer you see it , shows
two drivers but the second one always has the yellow error shield on it and if
you open it it stated driver not loaded.
Any help would
Unload vCom and try Com0Com. Get the 2.1.0.0 version.
http://kb.flex-radio.com/article.aspx?id=10481
http://kb.flex-radio.com/article.aspx?id=10482
-Tim
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED]
Sent: Tuesday, July 08, 2008
It not just Jeff. I'm one of the guys who've been listening to the
various audio tests. We first noticed something funny in someone
else's 5000 before Jeff even got his. We ran experiment after
experiment. This guy finally returned his for a refund. Then another
fellow (not in the
On Jul 8, 2008, at 12:18 PM, K6JEK wrote:
It not just Jeff. I'm one of the guys who've been listening to the
various audio tests. We first noticed something funny in someone
else's 5000 before Jeff even got his. We ran experiment after
experiment. This guy finally returned his for a
The 5/July Flex Radio Friends TeamSpeak
zipped mp3 (48 minutes) plus a text
file of channel comments is available at:
http://www.hamsdr.com/dnld.aspx?id=835
or
http://www.hamsdr.com/dnld.aspx
Mike - AA8K
___
FlexRadio Systems Mailing List
Thank you
Someone else can hear.
I was beginning to wonder.
On Tue, 2008-07-08 at 12:18 -0700, K6JEK wrote:
It not just Jeff. I'm one of the guys who've been listening to the
various audio tests. We first noticed something funny in someone
else's 5000 before Jeff even got his. We ran
I disagree that the 5000 audio is bad. I run both radios and they are fed with
a common microphone through a mixer. They both sound about the same when I
slightly tweak the eq. I run a PR-40, large diapghragm condensor, small element
condensor and a whole bunch of other mikes. I can make them
Hi Brian,
I've run THD (on the analog signals) and IMD (on the RF signals). What
I hear correlates strongly with IMD levels at lower powers (where much
of our voice energy is) when compared between 5K driver, 5K final, and a
1k. Correlation does not mean causality, but...no one has yet come
Edward J White wrote:
Was installing the RX2 and HRFIO unit when I noticed that there is a
cut wire going to the antenna tuner unit. The wire in question is from
the flat 9 wire cable which is hard wired to the AT then it goes to
the plug in plug on the transmitter unit. The wire is #9
Just upgraded the RFIO board to the new 34B version in my 5000 but I get
themessage
RFIO: Error or not present
I reset the database and get the same message. The Flex 5000 config dialog
shows my old RFIO serial number and version in RED, it used to be BLACK.
The ribbon cable is plugged
This FRS-recommended Dell Dimension E520 has no parallel port and no
serial port.
That makes it pretty much incompatible with SDR1K IMO.
I have gotten tired of the USB disconnects that occur several times per
hour of operation. So,
I bought a PARALLEL-PCI card from the Web. It is made by Lava
Hi All, I have bought several transceivers Flex5000 for russian ham from
the first running and at present. And I want to say, all transceiver
made before April of the month had and have problems SSB TX Audio. New
Flex5000 made after April, without problems, have clean and clear sound
TX. My
Hi Jeff,
I do not have a 5000, but it sounds as if you can set the bias on the PA
transistors with software. If that is the case, have you checked that
the quiescent current is really what it is supposed to be for the
transistors that are in the PA. If you have more distortion at lower
Was installing the RX2 and HRFIO unit when I noticed that there is a cut
wire going to the antenna tuner unit. The wire in question is from the
flat 9 wire cable which is hard wired to the AT then it goes to the plug
in plug on the transmitter unit. The wire is #9 (#1 is the red wire) of
the
Charles,
You need to send a copy of your authorization for that frequency, your
ham call, and serial number of the radio to [EMAIL PROTECTED] .. The
firmware update file has to be specially generated for the radio/ham
doing the requesting..
Be advised that Eric is busy with newborn,
Jim,
There is a EEPROM tool that is used to update the EEPROM... Should have
been a note included stating that you should contact Flex Support for
the tool and assistance to make the change.. Contact [EMAIL PROTECTED]
73,
Dudley
WA5QPZ
Jim R wrote:
Just upgraded the RFIO board to the new
Chuck,
The parallel port address on a PCI card should be a 4 digit number, so
you will have to manually type it into the Setup menu for the 1K.. To
find that address go to Windows Device Manager = Ports (Com LPT) =
your new LPT port right click on the new LPT = Properties
Resources ,
Not for under $300 and supported by PowerSDR.
73,
Dudley
WA5QPZ
Scott McClements wrote:
Hi,
I've been lurking on the list for awhile and haven't seen any talk
about any new soundcards that might outperform the recommended FA-66.
Is anyone actively trying to find any new, off the shelf
20 matches
Mail list logo
